1967 Ac 428 Automatic Transmission Parts

This table covers the apply bands inside the automatic transmission. Read more

3 Band parts are listed for the 1967 Ac 428, from ATP and PIONEER.

This group includes ATP FX125, ATP TPB1010 and PIONEER 767042.

This table covers the bushings in this assembly. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

5 Bushing parts for the 1967 Ac 428 come from 2 brands — PIONEER and ATP. The "Popular" part is PIONEER 755039.

This group includes PIONEER 755039, ATP FB115 and ATP FB106 and the remaining parts above.

This table covers the Bushing kits. Read more

This group shows a single part: ATP FBS2.

This table covers the Case bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND 36064HDBR.

This table covers the Clutch plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

PIONEER supplies the 3 Clutch Plate parts for the 1967 Ac 428.

In the Friction grade, PIONEER supplies 2 parts: grouped under the catalog's "Friction" designation — the notes column spells out what sets them apart. A representative part number is PIONEER 766011.

The Steel section lists 1 option from PIONEER — grouped under the catalog's "Steel" designation — the notes column spells out what sets them apart. PIONEER 766205 is listed in this group.

Part numbers include PIONEER 766011, PIONEER 766009 and PIONEER 766205.

This table covers the seals at the Control Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Control Shaft Seal parts for the 1967 Ac 428 come from 2 brands — ATP and PIONEER.

Listed part numbers: ATP FO15 and PIONEER 759003.

This table covers the Extension Housing bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND RP6189T.

This table covers the seals at the Extension Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Extension Housing Seal parts are listed for the 1967 Ac 428, from NATIONAL and WJB / INMOTION PARTS.

Part numbers include NATIONAL 7300S, NATIONAL 5203 and WJB / INMOTION PARTS WS7300S, among others listed above.

This table covers the replacement filters for this application — the table heading and notes say which circuit. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

6 Filter parts for the 1967 Ac 428 come from 2 brands — ATP and PIONEER. The "Popular" part is ATP JX151.

The Economy section lists 1 option from ATP — the catalog's value-priced group. ATP TF38 is listed in this group.

In the Standard Replacement grade, ATP and PIONEER supply 5 parts: built to original-equipment specification. A representative part number is ATP JX151.

This group includes ATP JX151, ATP TF38 and ATP IL150 and the remaining parts above.

This table covers the gaskets that seal the Filter. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Filter Gasket parts are listed for the 1967 Ac 428, from ATP and PIONEER.

Part numbers include ATP FG115 and PIONEER 7491065.

This table covers the gaskets that seal the Fluid Pan. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Fluid Pan Gasket parts for the 1967 Ac 428 come from 5 brands — FEL-PRO, ATP, MAHLE / CLEVITE and 2 other brands. The "Popular" part is FEL-PRO TOS18628.

This group includes FEL-PRO TOS18628, ATP FG114 and MAHLE / CLEVITE W39346 and the remaining parts above.

This table covers the Fluid Pump bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

3 Fluid Pump Bushing parts for the 1967 Ac 428 come from DURA-BOND.

This group includes DURA-BOND 02161F, DURA-BOND 02161FT and DURA-BOND 02161FTG.

This table covers the gaskets that seal the Fluid Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Fluid Pump Gasket parts are listed for the 1967 Ac 428, from ATP and PIONEER.

Listed part numbers: ATP FG113 and PIONEER 749072.

This table covers the Fluid Pump O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

2 Fluid Pump O-Ring parts for the 1967 Ac 428 come from 2 brands — ATP and PIONEER.

This group includes ATP FO151 and PIONEER 760004.

This table covers the precision wear sleeves used to restore a transmission pump seal surface. Read more

2 Fluid Pump Repair Sleeve parts are listed for the 1967 Ac 428, from NATIONAL and WJB / INMOTION PARTS.

This group includes NATIONAL 99199 and WJB / INMOTION PARTS WS99199.

This table covers the seals at the Fluid Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Fluid Pump Seal parts are listed for the 1967 Ac 428, from NATIONAL, ATP, BCA and 2 other brands. NATIONAL 331107N carries the "Popular" badge.

This group includes NATIONAL 331107N, ATP KO1 and BCA NS331107N and the remaining parts above.

This table covers the governors and modulators that control transmission shift pressure. Read more

6 Governor / Modulator parts for the 1967 Ac 428 come from 2 brands — ATP and PIONEER. The "Popular" part is ATP FX102.

Part numbers include ATP FX102, ATP FX194 and ATP FX263, among others listed above.

This table covers the seals at the Manual Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Manual Shaft Seal parts are listed for the 1967 Ac 428, from NATIONAL and WJB / INMOTION PARTS.

Part numbers include NATIONAL 7929S and WJB / INMOTION PARTS WS7929S.

This table covers the rebuild kits for this assembly. Read more

6 Rebuild Kit parts are listed for the 1967 Ac 428, from PIONEER, TRANSTEC and ATP. PIONEER 753010 carries the "Popular" badge.

In the Deluxe Kit (Master Kit + Filter, Band & Common Bushings) grade, PIONEER supplies 2 parts: grouped under the catalog's "Deluxe Kit (Master Kit + Filter, Band & Common Bushings)" designation — the notes column spells out what sets them apart. A representative part number is PIONEER 753010.

The Master Kit (Overhaul Kit + Friction & Steel Clutch Plates) section lists 2 options from ATP and PIONEER — grouped under the catalog's "Master Kit (Overhaul Kit + Friction & Steel Clutch Plates)" designation — the notes column spells out what sets them apart. ATP FM16 is listed in this group.

In the Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings) grade, TRANSTEC supplies 2 parts: grouped under the catalog's "Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings)" designation — the notes column spells out what sets them apart. A representative part number is TRANSTEC 81000011.

This group includes PIONEER 753010, PIONEER 753009 and ATP FM16 and the remaining parts above.

This table covers the Roller clutches. Typical signs include slip at highway speed, chatter on takeoff, or a pedal that stays low. Resurface or replace the flywheel with the clutch — a heat-checked flywheel wastes the new disc. Read more

One part is listed for the 1967 Ac 428 — BORG-WARNER 29055AM.

This table covers the Shift Improvement kits. Read more

5 Shift Improvement Kit parts for the 1967 Ac 428 come from 3 brands — TRANSGO, PIONEER and ATP. The "Popular" part is TRANSGO SK6.

In the Daily Driver grade, TRANSGO and PIONEER supply 2 parts: grouped for everyday commuting duty. A representative part number is TRANSGO SK6.

In the Heavy Duty grade, ATP supplies 1 part: rated for severe service. A representative part number is ATP FK6.

The High Performance section lists 2 options from TRANSGO — engineered beyond original-equipment specification. TRANSGO 6712 is listed in this group.

Part numbers include TRANSGO SK6, PIONEER 765001 and ATP FK6, among others listed above.

This table covers the Shift Linkage bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

ATP supplies both parts for the 1967 Ac 428.

This group includes ATP FO405 and ATP FO300.

This table covers the Sun Gear bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

4 Sun Gear Bushing parts are listed for the 1967 Ac 428, from DURA-BOND, ATP and PIONEER.

Listed part numbers: ATP FB113, DURA-BOND 02787BR and DURA-BOND 2787, plus the other parts above.