1970 Ac 428 Engine Parts

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Camshaft Bearing parts for the 1970 Ac 428 come from 2 brands — KING ENGINE BEARINGS and MAHLE / CLEVITE.

Part numbers include KING ENGINE BEARINGS CS515BB and MAHLE / CLEVITE SH781S.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: KING ENGINE BEARINGS CR809AM.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Crankshaft Main Bearing parts are listed for the 1970 Ac 428, from KING ENGINE BEARINGS and MAHLE / CLEVITE.

Part numbers include KING ENGINE BEARINGS MB559AM and MAHLE / CLEVITE MS863P.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts are listed for the 1970 Ac 428, from BCA, NATIONAL and WJB / INMOTION PARTS.

This group includes BCA NS88187, NATIONAL 99187 and WJB / INMOTION PARTS WS99187.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Crankshaft Seal parts are listed for the 1970 Ac 428, from FEL-PRO, NATIONAL, BCA and 3 other brands. FEL-PRO BS30138 carries the "Popular" badge.

This group includes FEL-PRO BS30138, NATIONAL 2942 and BCA NS2942 and the remaining parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Cylinder Head Gasket parts for the 1970 Ac 428 come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Part numbers include FEL-PRO 8554PT, MAHLE / CLEVITE 3389 and VICTOR REINZ 611032600.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Cylinder Head Gasket Set parts for the 1970 Ac 428 come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: FEL-PRO HS8554PT, MAHLE / CLEVITE HS3389VJ and VICTOR REINZ 021031801.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 1970 Ac 428 come from 2 brands — FEL-PRO and VICTOR REINZ.

This group includes FEL-PRO 8554SP and VICTOR REINZ 711383000.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts for the 1970 Ac 428 come from 2 brands — FEL-PRO and VICTOR REINZ.

Part numbers include FEL-PRO FS8554PT and VICTOR REINZ 011002701.

This table covers the wear sleeves used to restore a Harmonic Balancer seal surface. Read more

5 Harmonic Balancer Repair Sleeve parts are listed for the 1970 Ac 428, from MAHLE / CLEVITE, NATIONAL, BCA and 1 other brand. NATIONAL 88187 carries the "Popular" badge.

Listed part numbers: NATIONAL 88187, BCA NS88187 and MAHLE / CLEVITE A2262, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Intake Manifold Gasket parts for the 1970 Ac 428 come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO MS90145, MAHLE / CLEVITE MS15166X and VICTOR REINZ 111013701.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Drain Plug Gasket parts for the 1970 Ac 428 come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO 70822, MAHLE / CLEVITE 2051 and VICTOR REINZ 711346200.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

4 Oil Filter parts are listed for the 1970 Ac 428, from PUROLATOR and BOSCH.

In the Economy grade, PUROLATOR supplies 3 parts: the catalog's value-priced group. A representative part number is PUROLATOR 3500.

The Standard Replacement section lists 1 option from BOSCH — built to original-equipment specification. BOSCH 3500 is listed in this group.

Listed part numbers: PUROLATOR 3500, PUROLATOR 72102WS and PUROLATOR D3500, plus the other parts above.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: FEL-PRO 70135.

This table covers the gaskets that seal the Oil Filter. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Filter Gasket parts for the 1970 Ac 428 come from 2 brands — MAHLE / CLEVITE and VICTOR REINZ.

Part numbers include MAHLE / CLEVITE B25451 and VICTOR REINZ 711387600.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts are listed for the 1970 Ac 428, from FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE. FEL-PRO OS11701D carries the "Popular" badge.

This group includes FEL-PRO OS11701D, FEL-PRO OS11701C and MAHLE / CLEVITE OS30764 and the remaining parts above.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pump Gasket parts for the 1970 Ac 428 come from 2 brands — FEL-PRO and VICTOR REINZ.

Listed part numbers: FEL-PRO 11792 and VICTOR REINZ 711451000.

This table covers the gaskets that seal the Oil Pump Pickup Tube. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Pump Pickup Tube Gasket parts for the 1970 Ac 428 come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO 72516, MAHLE / CLEVITE B26151 and VICTOR REINZ 711350300.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 1970 Ac 428 — MAHLE / CLEVITE 2233501.

This table covers the rings that seal each piston to the cylinder wall. Read more

This group shows a single part: MAHLE / CLEVITE 50720.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Timing Cover Gasket parts are listed for the 1970 Ac 428, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. FEL-PRO TCS130751 carries the "Popular" badge.

Part numbers include FEL-PRO TCS130751, FEL-PRO TCS45167 and MAHLE / CLEVITE JV819, among others listed above.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

2 Timing Cover Repair Sleeve parts are listed for the 1970 Ac 428, from FEL-PRO and VICTOR REINZ.

Part numbers include FEL-PRO 16213 and VICTOR REINZ 711346500.

This table covers the Timing Cover Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

One part is listed for the 1970 Ac 428 — VICTOR REINZ 711541700.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 1970 Ac 428 — MAHLE / CLEVITE 46293.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts are listed for the 1970 Ac 428, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. FEL-PRO VS13049R carries the "Popular" badge.

This group includes FEL-PRO VS13049R, FEL-PRO VS13049C and MAHLE / CLEVITE VS38308R and the remaining parts above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Valve Stem Seal parts are listed for the 1970 Ac 428, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO SS13401, MAHLE / CLEVITE SS45390 and VICTOR REINZ 121007201.