1971 Am General DJ5 Engine Parts

Engine:
2.2L 134cid L4

This page lists 45 engine parts for the 1971 Am General DJ5, across 22 part types, covering the 2.2L 134cid L4 engine. Every part shows its brand, manufacturer part number and fitment notes.

On the 1971 Am General DJ5, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. 11 parts of the 45 listed are Crankshaft Seal (5 parts), Crankshaft Repair Sleeve (3 parts) and Cylinder Head Gasket (3 parts). The other 19 part types cover the remaining 34 parts.

Connecting Rod Bearing

Brand Part Number Markets Notes Buy
KING ENGINE BEARINGS CR401AM
🇺🇸 US
SetBimetal (Aluminum Base)
Fitment notes — KING ENGINE BEARINGS CR401AM
SetBimetal (Aluminum Base)
Standard
View on
Amazon

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly.

Crankshaft Main Bearing

Brand Part Number Markets Notes Buy
KING ENGINE BEARINGS MB319AM
🇺🇸 US
SetBimetal (Aluminum Base)
Fitment notes — KING ENGINE BEARINGS MB319AM
SetBimetal (Aluminum Base)
Standard Flange
View on
Amazon

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly.

Crankshaft Repair Sleeve

Brand Part Number Markets Notes Buy
NATIONAL 99174
🇺🇸 US
Front
View on
Amazon
SCHAEFFLER SR3496
🇺🇸 US
Frontwith 1.750 In Shaft
View on
Amazon
WJB / INMOTION PARTS WS99174
🇺🇸 US
Front
View on
Amazon

This table covers the sleeves used to restore a grooved crankshaft seal surface.

Crankshaft Seal

Brand Part Number Markets Notes Buy
FEL-PRO Popular BS3165
🇺🇸 US
Rope Type
Fitment notes — FEL-PRO BS3165
Rope Type
Rear
View on
Amazon
BCA NS471504
🇺🇸 US
Front
View on
Amazon
NATIONAL 471504
🇺🇸 US
Nitrile
Fitment notes — NATIONAL 471504
Nitrile
Front
View on
Amazon
VICTOR REINZ 191002201
🇺🇸 US
Set
Fitment notes — VICTOR REINZ 191002201
Set
RearRope Packing
View on
Amazon
WJB / INMOTION PARTS WS471504
🇺🇸 US
Nitrile
Fitment notes — WJB / INMOTION PARTS WS471504
Nitrile
Front
View on
Amazon

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Cylinder Head Gasket

Brand Part Number Markets Notes Buy
FEL-PRO 7543SBX
🇺🇸 US
View on
Amazon
MAHLE / CLEVITE 1057K
🇺🇸 US
Steel and Composite
View on
Amazon
VICTOR REINZ 611060600
🇺🇸 US
View on
Amazon

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Cylinder Head Gasket Set

Brand Part Number Markets Notes Buy
FEL-PRO HS7543SBX
🇺🇸 US
Includes Valve Stem Seals
View on
Amazon
VICTOR REINZ 021022701
🇺🇸 US
View on
Amazon

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.

Engine Kit Gasket Set

Brand Part Number Markets Notes Buy
FEL-PRO FS7543SBX
🇺🇸 US
Overhaul SetRear Main Seal Not Included
View on
Amazon
VICTOR REINZ 011006401
🇺🇸 US
View on
Amazon

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.

Exhaust Valve

Brand Part Number Markets Notes Buy
SBI 00303
🇺🇸 US
1 Groovewithout Rotator
View on
Amazon

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one.

Intake & Exhaust Manifold Gasket Set

Brand Part Number Markets Notes Buy
FEL-PRO MS9027B
🇺🇸 US
View on
Amazon
VICTOR REINZ 711478400
🇺🇸 US
View on
Amazon

This table covers the Intake & Exhaust Manifold gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.

Intake Valve

Brand Part Number Markets Notes Buy
SBI 00302
🇺🇸 US
View on
Amazon

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one.

O-Ring

Brand Part Number Markets Notes Buy
VICTOR REINZ 411038200
🇺🇸 US
View on
Amazon

This table covers the O-rings that seal this joint. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.

Oil Filter

Brand Part Number Markets Notes Buy
WIX 51050
🇺🇸 US
Height: 5.178 InSpin-On Filter
View on
Amazon

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.

Oil Pan Gasket

Brand Part Number Markets Notes Buy
FEL-PRO OS4350AD
🇺🇸 US
View on
Amazon
MAHLE / CLEVITE OS30656
🇺🇸 US
Cork-Rubber
View on
Amazon
VICTOR REINZ 101010301
🇺🇸 US
View on
Amazon

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Piston

Brand Part Number Markets Notes Buy
SILV-O-LITE 2606
🇺🇸 US
Centered Pin ConfigurationPress Pin Type
Fitment notes — SILV-O-LITE 2606
Centered Pin ConfigurationPress Pin TypeFlat Top
View on
Amazon

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo.

Push Rod Gasket Set

Brand Part Number Markets Notes Buy
FEL-PRO PS4352C
🇺🇸 US
View on
Amazon
MAHLE / CLEVITE VS38055
🇺🇸 US
Cork-Rubber
View on
Amazon
VICTOR REINZ 181006301
🇺🇸 US
View on
Amazon

This table covers the Push Rod gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.

Timing Cover Gasket

Brand Part Number Markets Notes Buy
FEL-PRO TCS43511
🇺🇸 US
View on
Amazon
MAHLE / CLEVITE JV797
🇺🇸 US
Set
View on
Amazon
VICTOR REINZ 151035901
🇺🇸 US
Set
View on
Amazon

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Valve Cover Gasket

Brand Part Number Markets Notes Buy
FEL-PRO VS6617C
🇺🇸 US
Cork
View on
Amazon
MAHLE / CLEVITE VS38092
🇺🇸 US
Cork-Rubber
View on
Amazon
VICTOR REINZ 151117301
🇺🇸 US
Improved DesignSet
View on
Amazon

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Valve Guide

Brand Part Number Markets Notes Buy
SBI 1401704
🇺🇸 US
Intake0.3750 I.D.
Fitment notes — SBI 1401704
Intake0.3750 I.D.0.6580 O.D.2.375 Length8-P Type
View on
Amazon
SBI 1401342
🇺🇸 US
Exhaust0.3750 I.D.
Fitment notes — SBI 1401342
Exhaust0.3750 I.D.0.6580 O.D.3.063 Length11-P Type
View on
Amazon

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering.

Valve Seat

Brand Part Number Markets Notes Buy
SBI SB21251
🇺🇸 US
High ChromeFor Cast Iron Cylinder Head
Fitment notes — SBI SB21251
High ChromeFor Cast Iron Cylinder Head
Intake2-1/8 O.D.1-13/16 I.D.1/4 Depth2.000 Head DiameterLong Groove
View on
Amazon
SBI SB15624
🇺🇸 US
Exhaust1-9/16 O.D.
Fitment notes — SBI SB15624
Exhaust1-9/16 O.D.1-5/16 I.D.1/4 Depth
View on
Amazon

This table covers the Valve seats.

Valve Spring

Brand Part Number Markets Notes Buy
SBI 1601114
🇺🇸 US
Exhaust2.533 Length
Fitment notes — SBI 1601114
Exhaust2.533 Length1.188 O.D.0.864 I.D
View on
Amazon
SBI 1601115
🇺🇸 US
Intake1.970 Length
Fitment notes — SBI 1601115
Intake1.970 Length1.239 O.D.0.885 I.D
View on
Amazon

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats.

Valve Spring Retainer Keeper

Brand Part Number Markets Notes Buy
SBI 1211003
🇺🇸 US
Exhaust0.3770 Length
Fitment notes — SBI 1211003
Exhaust0.3770 Length1 Square Bead Type0.3365 I.D.
View on
Amazon
SBI 1211046
🇺🇸 US
Intake0.3060 Length
Fitment notes — SBI 1211046
Intake0.3060 LengthNo Bead Type0.2435 I.D.Long Groove
View on
Amazon

This table covers the keepers that lock each valve-spring retainer to the stem.

Valve Stem Seal

Brand Part Number Markets Notes Buy
FEL-PRO 407
🇺🇸 US
Intake
View on
Amazon

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Buying Engine Parts for a 1971 Am General DJ5

On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.

  • Confirm you have the 2.2L 134cid L4 engine — every part on this page is matched to it.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Crankshaft Seal and Crankshaft Repair Sleeve .

Frequently Asked Questions

How many engine parts fit the 1971 Am General DJ5?

Our catalog currently lists 45 engine parts for the 1971 Am General DJ5 across 22 subcategories and 11 brands, covering the 2.2L 134cid L4 engine. Each part is matched to the engine(s) it fits.

What are the signs of engine problems on a 1971 Am General DJ5?

Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What should I replace at the same time?

Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1971 Am General DJ5 was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 1971 Am General DJ5?

Every part on this page is matched to the 2.2L 134cid L4 engine. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 1971 Am General DJ5

Engine Parts for Other Am General DJ5 Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.