2018 Audi RS3 Engine Parts

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

2 Camshaft Repair Sleeve parts for the 2018 Audi RS3 come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: NATIONAL 99128 and WJB / INMOTION PARTS WS99128.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Camshaft Seal parts for the 2018 Audi RS3 come from 4 brands — AJUSA, BCA, NATIONAL and 1 other brand.

Listed part numbers: AJUSA 01567100, BCA NS3476 and NATIONAL 3476, plus the other parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2018 Audi RS3 — AJUSA 54295100.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Crankshaft Seal parts for the 2018 Audi RS3 come from 5 brands — WJB / INMOTION PARTS, MAHLE / CLEVITE, VICTOR REINZ and 2 other brands. The "Popular" part is MAHLE / CLEVITE 67830.

This group includes MAHLE / CLEVITE 67830, VICTOR REINZ 813555300 and AJUSA 15084000 and the remaining parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

One part is listed for the 2018 Audi RS3 — AJUSA 81068900.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2018 Audi RS3 — AJUSA 10230100.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2018 Audi RS3 — AJUSA 52549700.

This table covers the Cylinder Head temperature sensors. Typical signs include hard cold starts, a fan that never comes on, or a gauge that disagrees with the scan tool. A sensor that reads open or shorted is usually the part; an implausible-but-smooth reading can be wiring. Read more

This group shows a single part: GPD 1814595.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2018 Audi RS3 — AJUSA 50503600.

This table covers the followers that drive a mechanical fuel pump off the camshaft. Read more

3 Fuel Pump Camshaft Follower parts are listed for the 2018 Audi RS3, from ASTEMO / HITACHI, VEMO and WELLS.

Part numbers include ASTEMO / HITACHI HCF3057, VEMO V10250019 and WELLS 5T5004.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2018 Audi RS3 — AJUSA 13283200.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 13237700.

This table covers the seals at the Intermediate Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: BCA NS3476.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

5 Motor Mount parts for the 2018 Audi RS3 come from 2 brands — PIONEER and ANCHOR. The "Popular" part is ANCHOR 9919.

Listed part numbers: ANCHOR 9919, ANCHOR 9918 and PIONEER 600918, plus the other parts above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

4 Oil parts for the 2018 Audi RS3 come from 2 brands — LIQUI MOLY and VALVOLINE.

Part numbers include LIQUI MOLY 22156, LIQUI MOLY 22158 and VALVOLINE 893931, among others listed above.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2018 Audi RS3 — AJUSA 77008600.

This table covers the seals at the Oil Cooler. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2018 Audi RS3 — DORMAN 926601.

This table covers the drain plugs in the oil pan. Read more

5 Oil Drain Plug parts for the 2018 Audi RS3 come from 2 brands — VAICO and REIN. The "Popular" part is VAICO V104947.

Part numbers include VAICO V104947, REIN HWP1014 and REIN HWU1014, among others listed above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts are listed for the 2018 Audi RS3, from DORMAN, FEL-PRO, JAPANESE OE and 1 other brand. DORMAN 095147 carries the "Popular" badge.

Part numbers include DORMAN 095147, DORMAN 995147CD and FEL-PRO 73350, among others listed above.

This table covers the caps on the oil filler neck. Read more

3 Oil Filler Cap parts for the 2018 Audi RS3 come from 3 brands — DORMAN, REIN and VAICO.

This group includes DORMAN 80989, REIN CPL0046 and VAICO V107328.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

25 Oil Filter parts for the 2018 Audi RS3 come from 17 brands — CHAMP / LUBER-FINER, FRAM, FVP and 14 other brands. The "Popular" part is PRO-TEC PXL57187.

The Economy section lists 8 options from PUROLATOR, PRO-TEC, CHAMP / LUBER-FINER and 4 other brands — the catalog's value-priced group. PRO-TEC PXL57187 is listed in this group.

The High Performance / Heavy Duty section lists 4 options from MOBIL, WIX and FRAM — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 57187XP is listed in this group.

In the Standard Replacement grade, HASTINGS / BALDWIN, HENGST, MANN and 9 other brands supply 13 parts: built to original-equipment specification. A representative part number is HENGST E27HD125.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

One part is listed for the 2018 Audi RS3 — VICTOR REINZ 713756900.

This table covers the Oil Filter covers. Read more

5 Oil Filter Cover parts are listed for the 2018 Audi RS3, from VAICO, DORMAN, MOTORAD and 1 other brand. DORMAN 921171 carries the "Popular" badge.

Part numbers include DORMAN 921171, MOTORAD MO346 and REIN CPL0053, among others listed above.

This table covers the Oil Filter housings. Read more

One part is listed for the 2018 Audi RS3 — HENGST H816H.

This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

3 Oil Level Sensor parts for the 2018 Audi RS3 come from 3 brands — HELLA, VEMO and VNE.

Listed part numbers: HELLA 013680091, VEMO V10721427 and VNE 700043.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pan Gasket parts for the 2018 Audi RS3 come from 2 brands — ELRING and VICTOR REINZ.

Listed part numbers: ELRING 030793 and VICTOR REINZ 703141410.

This table covers the Oil Pump Control Valve solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

One part is listed for the 2018 Audi RS3 — DORMAN 916880.

This table covers the guides and dampers that keep the timing chain on its path. Read more

One part is listed for the 2018 Audi RS3 — ÜRO PARTS 079109470.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

2 Torque Strut Mount parts are listed for the 2018 Audi RS3, from ANCHOR and DEA / MARMON RIDE CONTROL.

Listed part numbers: ANCHOR 10326 and DEA / MARMON RIDE CONTROL A4984.

This table covers the turbochargers that compress intake air. Read more

3 Turbocharger parts for the 2018 Audi RS3 come from 2 brands — BORG-WARNER and GPD.

This group includes BORG-WARNER 18559880036, BORG-WARNER 18559880037 and GPD 2511772.

This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

2 Turbocharger Boost Sensor parts are listed for the 2018 Audi RS3, from HELLA and WELLS.

Listed part numbers: HELLA 358152261 and WELLS 5S15123.

This table covers the Turbocharger Diverter / Bypass valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

4 Turbocharger Diverter / Bypass Valve parts for the 2018 Audi RS3 come from 4 brands — DORMAN, PIERBURG, SKP and 1 other brand.

Listed part numbers: DORMAN 911240, PIERBURG 702901050 and SKP SK911240, plus the other parts above.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2018 Audi RS3 — AJUSA JTC12470.

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

This group shows a single part: AJUSA OP11076.

This table covers the Turbocharger Oil Line Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: AJUSA 01200600.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Valve Cover Gasket parts for the 2018 Audi RS3 come from 2 brands — AJUSA and VICTOR REINZ.

Listed part numbers: AJUSA 75000400 and VICTOR REINZ 703141410.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

2 Valve Guide parts for the 2018 Audi RS3 come from 2 brands — ENGINETECH and TOPLINE.

This group includes ENGINETECH GD3027 and TOPLINE VGVW21.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

5 Valve Lifter parts for the 2018 Audi RS3 come from 5 brands — MELLING, AJUSA, ENGINETECH and 2 other brands. The "Popular" part is MELLING JB7532.

Part numbers include MELLING JB7532, AJUSA 85009000 and ENGINETECH L4332, among others listed above.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

3 Valve Spring Retainer Keeper parts are listed for the 2018 Audi RS3, from MELLING, QUALCAST and SBI.

Part numbers include MELLING VL1098, QUALCAST 345021 and SBI 1211098.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Valve Stem Seal parts for the 2018 Audi RS3 come from 4 brands — AJUSA, ENGINETECH, MAHLE / CLEVITE and 1 other brand.

Listed part numbers: AJUSA 12037600, AJUSA 57077700 and ENGINETECH S5940, plus the other parts above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

9 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2018 Audi RS3 come from 8 brands — SKP, DORMAN, GATES and 5 other brands. The "Popular" part is SKP SK918130.

The Economy section: 7 options from SKP, DORMAN, GATES and 3 other brands. SKP SK918130 is listed in this group.

Standard Replacement: 2 parts, from BECK/ARNLEY and STANDARD MOTOR PRODUCTS. A representative part number is BECK/ARNLEY 0242143.

Part numbers include SKP SK918130, SKP SK918134 and DORMAN 918130, among others listed above.