2025 Audi A6 Cooling System Parts

Engine:

Showing parts for every engine. Select an engine to see only what fits.

This page lists 44 cooling system parts for the 2025 Audi A6, across 13 part types, covering all 3 engine options (2.0L L4 Turbocharged, 3.0L V6 Turbocharged and ELECTRIC). Every part shows its brand, manufacturer part number and fitment notes.

On the 2025 Audi A6, the cooling system system keeps operating temperature in the narrow band the engine was designed for, from radiator and water pump to thermostat and hoses. Most of the listed parts are Water Pump (16 parts), Temperature Sender / Sensor (7 parts) and Intercooler (5 parts). The other 10 part types cover the remaining 16 parts.

Coolant / Antifreeze

Economy

Brand Part Number Markets Notes Buy
VALVOLINE Fits: 2.0L L4 Turbocharged 719009
🇺🇸 US 🇨🇦 CA
Multi-Vehicle Yellow1 Gallon
View on
Amazon

Standard Replacement

Brand Part Number Markets Notes Buy
VALVOLINE Fits: 2.0L L4 Turbocharged 904683
🇺🇸 US 🇨🇦 CA
HT-12 Pink1 Gallon
Fitment notes — VALVOLINE 904683
HT-12 Pink1 Gallon
(Type: Concentrated)
View on
Amazon
Brand Part Number Markets Notes Buy
VALVOLINE Fits: 3.0L V6 Turbocharged, ELECTRIC 904683
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
HT-12 Pink1 Gallon
Fitment notes — VALVOLINE 904683
HT-12 Pink1 Gallon
(Type: Concentrated)
View on
Amazon

This table covers the engine coolants and antifreeze formulations specified for this cooling system. Typical signs include a rising temperature gauge, rusty or sludged coolant, or a heater that blows cold. Use the chemistry named in the notes. Mixing silicate, OAT and HOAT formulas can gel in the radiator.

Coolant Hose / Pipe

Brand Part Number Markets Notes Buy
REIN Fits: 2.0L L4 Turbocharged CHP0663
🇺🇸 US 🇨🇦 CA
Pipe
Fitment notes — REIN CHP0663
Pipe
Oil Cooler To Thermostat
View on
Amazon

This table covers the hard pipes and extra hoses in the coolant circuit.

Coolant Reservoir Cap

Brand Part Number Markets Notes Buy
MOTORAD Fits: 2.0L L4 Turbocharged, 3.0L V6 Turbocharged T111
🇺🇸 US 🇨🇦 CA
Standard
Fitment notes — MOTORAD T111
Standard
Relief Pressure 23 lbs
View on
Amazon
MOTORAD Fits: ELECTRIC T143
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Standard
Fitment notes — MOTORAD T143
Standard
Relief Pressure 10 lbs
View on
Amazon

This table covers the caps on the overflow / expansion tank. Typical signs include a leak at the neck, a cap that will not hold pressure, or a missing tether. Match the pressure rating or thread in the notes — radiator, reservoir and fuel caps are not interchangeable.

Intercooler

Brand Part Number Markets Notes Buy
GPD Fits: 2.0L L4 Turbocharged 2711413
🇺🇸 US 🇨🇦 CA
View on
Amazon
HELLA Fits: 2.0L L4 Turbocharged 366340871
🇺🇸 US
View on
Amazon
NISSENS Fits: 2.0L L4 Turbocharged 961466
🇺🇸 US
View on
Amazon
NISSENS Fits: 3.0L V6 Turbocharged 961345
🇺🇸 US
View on
Amazon
TECHPRO Fits: 2.0L L4 Turbocharged AU3012112
🇺🇸 US 🇨🇦 CA
View on
Amazon

This table covers the intercoolers that cool turbo or supercharger charge air.

Radiator

Brand Part Number Markets Notes Buy
CSF Fits: 3.0L V6 Turbocharged 4002
🇺🇸 US 🇨🇦 CA
View on
Amazon
NISSENS Fits: 2.0L L4 Turbocharged 606573
🇺🇸 US
Brazed cooling fins
View on
Amazon
NISSENS Fits: 3.0L V6 Turbocharged 606578
🇺🇸 US
Brazed cooling fins
View on
Amazon
SPECTRA PREMIUM Fits: 2.0L L4 Turbocharged CU13665
🇺🇸 US 🇨🇦 CA
View on
Amazon

This table covers the radiators that dump engine heat to airflow through the core. Typical signs include overheating in traffic, a wet core, or coolant that disappears with no puddle. Replace the cap if it cannot hold the rated pressure, and bleed the system after the swap.

Radiator Fan Shroud

Brand Part Number Markets Notes Buy
SKP Fits: 2.0L L4 Turbocharged, 3.0L V6 Turbocharged SK621318
🇺🇸 US
View on
Amazon

This table covers the shrouds that duct air through the fan and radiator.

Radiator Insulator Sleeve

Brand Part Number Markets Notes Buy
REIN Fits: 2.0L L4 Turbocharged, 3.0L V6 Turbocharged AVM0730
🇺🇸 US 🇨🇦 CA
View on
Amazon

This table covers the Radiator Insulator sleeves.

Radiator Mount

Brand Part Number Markets Notes Buy
REIN Fits: 2.0L L4 Turbocharged, 3.0L V6 Turbocharged AVM0729
🇺🇸 US 🇨🇦 CA
Upper
View on
Amazon

This table covers the Radiator mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes.

Temperature Sender / Sensor

Economy

Brand Part Number Markets Notes Buy
HOLSTEIN Fits: 3.0L V6 Turbocharged 2CTS0163
🇺🇸 US 🇨🇦 CA
Lower
View on
Amazon

Standard Replacement

Brand Part Number Markets Notes Buy
STANDARD MOTOR PRODUCTS Popular Fits: 3.0L V6 Turbocharged TX275
🇺🇸 US 🇨🇦 CA
Attachment Method: Bolt On
Fitment notes — STANDARD MOTOR PRODUCTS TX275
Attachment Method: Bolt On
Fits:
Located on Engin
or:
Engine Block
View on
Amazon
NISSENS Fits: 3.0L V6 Turbocharged 207067
🇺🇸 US
Oval Connector, bolted connection
View on
Amazon
VNE Fits: 3.0L V6 Turbocharged 9408050
🇺🇸 US 🇨🇦 CA
Lower
View on
Amazon
WELLS Fits: 3.0L V6 Turbocharged 5S16784
🇺🇸 US 🇨🇦 CA
Lower
View on
Amazon
Brand Part Number Markets Notes Buy
NISSENS Fits: 2.0L L4 Turbocharged 207067
🇺🇸 US
Oval Connector, bolted connection
View on
Amazon
STANDARD MOTOR PRODUCTS Fits: 2.0L L4 Turbocharged TX275
🇺🇸 US 🇨🇦 CA
Attachment Method: Bolt On
Fitment notes — STANDARD MOTOR PRODUCTS TX275
Attachment Method: Bolt On
Located on Radiator Hose
View on
Amazon

This table covers the senders that report coolant temperature to the gauge or ECU. Typical signs include a gauge that sits on empty or overheat, or a lamp that does not match what the engine is doing. Rule out the cluster and the wiring before replacing the sender.

Thermostat

Brand Part Number Markets Notes Buy
MOTORAD Fits: 3.0L V6 Turbocharged 1229221
🇺🇸 US 🇨🇦 CA
Includes Sensor and SealStandard
Fitment notes — MOTORAD 1229221
Includes Sensor and SealStandard
221 Degrees FOE Specified Temperature
View on
Amazon

This table covers the thermostats that open the coolant circuit at the specified temperature. Typical signs include slow warm-up, a gauge that climbs in traffic, or heat that never quite arrives. Replace the housing gasket with the thermostat and bleed the system so a trapped air pocket does not cook the new part.

Thermostat / Thermostat Housing / Water Outlet Seal

Brand Part Number Markets Notes Buy
MAHLE / CLEVITE Fits: 2.0L L4 Turbocharged 72622
🇺🇸 US 🇨🇦 CA
Outlet Flange O-Ring 3mm X 32mmFPM Rubber
Fitment notes — MAHLE / CLEVITE 72622
Outlet Flange O-Ring 3mm X 32mmFPM RubberWater Outlet Seal
View on
Amazon

This table covers the seals at the thermostat housing and water outlet. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Thermostat Housing / Water Outlet

Brand Part Number Markets Notes Buy
MOTORAD Fits: 2.0L L4 Turbocharged CH3116
🇺🇸 US 🇨🇦 CA
Water Outlet
View on
Amazon

This table covers the housings and outlets the thermostat sits in.

Water Pump

Economy

Brand Part Number Markets Notes Buy
BECK/ARNLEY Popular Fits: 2.0L L4 Turbocharged 1312517
🇺🇸 US 🇨🇦 CA
Resin Impeller
Fitment notes — BECK/ARNLEY 1312517
Resin Impeller
Metal Impeller
View on
Amazon
US MOTOR WORKS Popular Fits: 2.0L L4 Turbocharged US8124
🇺🇸 US 🇨🇦 CA
View on
Amazon
BECK/ARNLEY Fits: 2.0L L4 Turbocharged, 3.0L V6 Turbocharged 1312562
🇺🇸 US 🇨🇦 CA
HVAC SystemAuxiliary
View on
Amazon
FVP Fits: 2.0L L4 Turbocharged US8124
🇺🇸 US 🇨🇦 CA
View on
Amazon

Standard Replacement

Brand Part Number Markets Notes Buy
GATES Popular Fits: 3.0L V6 Turbocharged 41568E
🇺🇸 US 🇨🇦 CA
Electric
Fitment notes — GATES 41568E
Electric
To TurbochargerAuxiliary
View on
Amazon
GATES Popular Fits: 3.0L V6 Turbocharged 41592E
🇺🇸 US 🇨🇦 CA
Electric
Fitment notes — GATES 41592E
Electric
HeaterAuxiliary
View on
Amazon
GMB Popular Fits: 2.0L L4 Turbocharged 1803050
🇺🇸 US 🇨🇦 CA
Primary Pump
View on
Amazon
FOUR SEASONS Fits: 2.0L L4 Turbocharged 89087
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with Transmission Oil CoolerAuxiliary
View on
Amazon
FOUR SEASONS Fits: 2.0L L4 Turbocharged, 3.0L V6 Turbocharged 89085
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
RearHeater Water Pump
View on
Amazon
FOUR SEASONS Fits: 3.0L V6 Turbocharged 89084
🇺🇸 US 🇨🇦 CA
RightAuxiliary
View on
Amazon
NISSENS Fits: 2.0L L4 Turbocharged, 3.0L V6 Turbocharged 832172
🇺🇸 US
HVAC SystemAuxiliary
View on
Amazon
NISSENS Fits: 2.0L L4 Turbocharged 832152
🇺🇸 US
Engine CoolingAuxiliary
View on
Amazon
NISSENS Fits: 3.0L V6 Turbocharged 832121
🇺🇸 US
Engine CoolingAuxiliary
View on
Amazon
PIERBURG Fits: 2.0L L4 Turbocharged 707152290
🇺🇸 US
Includes GasketMechanical
View on
Amazon
SALERI Fits: 2.0L L4 Turbocharged PA1532
🇺🇸 US 🇨🇦 CA
MechanicalNon-switchable water pump
View on
Amazon
Brand Part Number Markets Notes Buy
HELLA Fits: 3.0L V6 Turbocharged 358304701
🇺🇸 US
Engine CoolingAuxiliary
View on
Amazon

This table covers the pumps that circulate coolant through the block and radiator. Typical signs include coolant at the weep hole, pulley play, or a growl from the front of the engine. Replace the thermostat and refill with the specified coolant whenever the pump comes off.

Buying Cooling System Parts for a 2025 Audi A6

On this vehicle, the cooling system system keeps operating temperature in the narrow band the engine was designed for, from radiator and water pump to thermostat and hoses.

  • Match the engine first. Every cooling system part here is engine-specific; each row shows which engine(s) it fits.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace the thermostat and refill with fresh coolant whenever you change a water pump or radiator; original hoses on an older vehicle are on borrowed time.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Water Pump and Temperature Sender / Sensor .

Frequently Asked Questions

How many cooling system parts fit the 2025 Audi A6?

Our catalog currently lists 44 cooling system parts for the 2025 Audi A6 across 13 subcategories and 23 brands, covering all 3 engine options (2.0L L4 Turbocharged, 3.0L V6 Turbocharged and ELECTRIC). Each part is matched to the engine(s) it fits.

Do cooling system parts differ between 2025 Audi A6 engines?

Yes. Every cooling system part on this page is engine-specific. Each row shows which engine(s) it fits — use the filter at the top to hide the rest. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.

What are the signs of cooling system problems on a 2025 Audi A6?

Common symptoms include a rising temperature gauge in traffic, sweet-smelling steam, crusty deposits around hose clamps, or a heater that blows cold. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What should I replace at the same time?

Where labor overlaps, replace the thermostat and refill with fresh coolant whenever you change a water pump or radiator; original hoses on an older vehicle are on borrowed time.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2025 Audi A6 was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 2025 Audi A6?

First match the engine — each row shows which engine(s) the part fits. Then replace coolant with the exact specification the manufacturer calls for — mixing chemistries can gel and block small passages. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 2025 Audi A6

Cooling System Parts for Other Audi A6 Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.