2018 Baic BJ40 Engine Parts

Engine:
2.3L L4 Turbocharged

The 2018 Baic BJ40 has 7 engine parts with verified fitment on this page — 5 part types and 2 brands, covering the 2.3L L4 Turbocharged engine. Each part includes a manufacturer part number and application notes.

On the 2018 Baic BJ40, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. 5 parts of the 7 listed are Crankshaft Seal (2 parts), Oil Filter (2 parts) and Cylinder Head Bolt (1 part). The other 2 part types cover the remaining 2 parts.

Crankshaft Seal

Brand Part Number Markets Notes Buy
ELRING 330965
🇲🇽 MX
Outer Diameter [mm]: 66,65
Fitment notes — ELRING 330965
Outer Diameter [mm]: 66,65
Front
View on
Amazon
ELRING 750476
🇲🇽 MX
Height [MM]: 11Inner Diameter [mm]: 88
Fitment notes — ELRING 750476
Height [MM]: 11Inner Diameter [mm]: 88Material: FPM (Fluoride Rubber)Outer Diameter [mm]: 108Radial Shaft Seal Design: ASWSwirl Type: Left-hand Twist
RearTransmission Side
View on
Amazon

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Cylinder Head Bolt

Brand Part Number Markets Notes Buy
ELRING 221280
🇲🇽 MX
SetBolt Head-/Nut Design: Male Torx
Fitment notes — ELRING 221280
SetBolt Head-/Nut Design: Male TorxThread Size: M12X1,75x99
View on
Amazon

This table covers the bolts that clamp the cylinder head to the block.

Cylinder Head Gasket

Brand Part Number Markets Notes Buy
ELRING 400983
🇲🇽 MX
Diameter [MM]: 91Material: Multi-Layer Steel (MLS)
View on
Amazon

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Oil Filter

Economy

Brand Part Number Markets Notes Buy
VARIOUS MFR PG241
🇲🇽 MX
Spin-On
View on
Amazon

Standard Replacement

Brand Part Number Markets Notes Buy
VARIOUS MFR PG241EX
🇲🇽 MX
Extended LifeSpin-On
View on
Amazon

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.

Valve Stem Seal

Brand Part Number Markets Notes Buy
ELRING 392510
🇲🇽 MX
Height [MM]: 19,5
View on
Amazon

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Buying Engine Parts for a 2018 Baic BJ40

On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.

  • Confirm you have the 2.3L L4 Turbocharged engine — every part on this page is matched to it.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Crankshaft Seal and Oil Filter .

Frequently Asked Questions

How many engine parts fit the 2018 Baic BJ40?

Our catalog currently lists 7 engine parts for the 2018 Baic BJ40 across 5 subcategories and 2 brands, covering the 2.3L L4 Turbocharged engine. Each part is matched to the engine(s) it fits.

What are the signs of engine problems on a 2018 Baic BJ40?

Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What should I replace at the same time?

Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2018 Baic BJ40 was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 2018 Baic BJ40?

Every part on this page is matched to the 2.3L L4 Turbocharged engine. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 2018 Baic BJ40

Engine Parts for Other Baic BJ40 Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.