2024 BMW 230I Engine Parts

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2024 BMW 230I — AJUSA 54303200.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Crankshaft Seal parts for the 2024 BMW 230I come from 2 brands — AJUSA and MAHLE / CLEVITE.

Listed part numbers: AJUSA 15075200, AJUSA 15107900 and MAHLE / CLEVITE 68123.

This table covers the bolts that clamp the cylinder head to the block. Read more

One part is listed for the 2024 BMW 230I — AJUSA 81065000.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

AJUSA supplies both parts for the 2024 BMW 230I.

Part numbers include AJUSA 10248100 and AJUSA 10248110.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2024 BMW 230I — AJUSA 52641900.

This table covers the Engine covers. Read more

TECHPRO supplies both parts for the 2024 BMW 230I.

Part numbers include TECHPRO BM1228186 and TECHPRO BM1228190.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2024 BMW 230I — AJUSA 50570400.

This table covers the Harmonic Balancer bolts. Read more

This group shows a single part: REIN HWB0074.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2024 BMW 230I — AJUSA 13313000.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

7 Motor Mount parts for the 2024 BMW 230I come from 3 brands — REIN, ÜRO PARTS and ANCHOR. The "Popular" part is ÜRO PARTS 22117581618.

The Economy section lists 2 options from ÜRO PARTS — the catalog's value-priced group. ÜRO PARTS 22117581618 is listed in this group.

In the Standard Replacement grade, REIN and ANCHOR supply 5 parts: built to original-equipment specification. A representative part number is ANCHOR 10343.

This group includes ÜRO PARTS 22117581618, ÜRO PARTS 22117581617 and ANCHOR 10343 and the remaining parts above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

6 Oil parts for the 2024 BMW 230I come from 3 brands — LIQUI MOLY, PENTOSIN and VALVOLINE. The "Popular" part is LIQUI MOLY 22044.

This group includes LIQUI MOLY 22044, LIQUI MOLY 22046 and LIQUI MOLY 22048 and the remaining parts above.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

2 Oil Cooler parts for the 2024 BMW 230I come from 2 brands — MAHLE / CLEVITE and NISSENS.

This group includes MAHLE / CLEVITE CLC362000S and NISSENS 91395.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2024 BMW 230I — AJUSA 77031200.

This table covers the drain plugs in the oil pan. Read more

2 Oil Drain Plug parts for the 2024 BMW 230I come from 2 brands — DORMAN and REIN.

Part numbers include DORMAN 090088 and REIN HWU1041.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2024 BMW 230I — AJUSA 21010400.

This table covers the caps on the oil filler neck. Read more

This group shows a single part: MOTORAD MO214.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

14 Oil Filter parts for the 2024 BMW 230I come from 13 brands — WIX, PRO-TEC, CHAMP / LUBER-FINER and 10 other brands. The "Popular" part is PRO-TEC PXL10358.

The Economy section: 4 options from PRO-TEC, CHAMP / LUBER-FINER, FVP and 1 other brand. PRO-TEC PXL10358 is listed in this group.

The High Performance / Heavy Duty section lists 2 options from MOBIL and WIX — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1C354A is listed in this group.

Standard Replacement: 8 parts, from MAHLE / CLEVITE, MANN, BECK/ARNLEY and 5 other brands. A representative part number is MAHLE / CLEVITE OX8132D.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

One part is listed for the 2024 BMW 230I — MAHLE / CLEVITE B33885.

This table covers the Oil Filter covers. Read more

One part is listed for the 2024 BMW 230I — MOTORAD MO373.

This table covers the Oil Filter housings. Read more

3 Oil Filter Housing parts are listed for the 2024 BMW 230I, from ÜRO PARTS and DORMAN.

Listed part numbers: DORMAN 918943, ÜRO PARTS 11428580414 and ÜRO PARTS 11428580414PRM.

This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: AJUSA 16078650.

This table covers the oil pans that hold the engine's oil sump. Read more

REIN supplies both parts for the 2024 BMW 230I.

Listed part numbers: REIN ESK0244 and REIN ESK0235.

This table covers the chains that drive the oil pump. Read more

One part is listed for the 2024 BMW 230I — CLOYES C529.

This table covers the Oil Pump sprockets. Read more

One part is listed for the 2024 BMW 230I — CLOYES S1172.

This table covers the timing chains that keep the cams in time with the crank. Read more

One part is listed for the 2024 BMW 230I — CLOYES C528.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

2 Timing Chain & Component Kit parts for the 2024 BMW 230I come from CLOYES.

Part numbers include CLOYES 90528SX and CLOYES 90528S.

This table covers the guides and dampers that keep the timing chain on its path. Read more

CLOYES supplies the 3 Timing Chain Guide / Damper parts for the 2024 BMW 230I.

Listed part numbers: CLOYES 96180, CLOYES 96181 and CLOYES 96182.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: CLOYES 96179.

This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

One part is listed for the 2024 BMW 230I — WELLS 5S14741.

This table covers the Turbocharger Coolant lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

2 Turbocharger Coolant Line parts for the 2024 BMW 230I come from REIN.

This group includes REIN CHT0924 and REIN CHT0923.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

AJUSA supplies both parts for the 2024 BMW 230I.

Listed part numbers: AJUSA 01335100 and AJUSA JTC12488.

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

4 Turbocharger Oil Line parts for the 2024 BMW 230I come from 3 brands — REIN, AJUSA and ÜRO PARTS.

This group includes AJUSA OP11220, REIN TRP0377 and REIN TFP0376 and the remaining parts above.

This table covers the Turbocharger Wastegate Solenoid actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

This group shows a single part: DORMAN 667845.

This table covers the Valve covers. Read more

One part is listed for the 2024 BMW 230I — SKP SK743462.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Valve Cover Gasket parts for the 2024 BMW 230I come from 2 brands — AJUSA and MAHLE / CLEVITE.

This group includes AJUSA 56094000 and MAHLE / CLEVITE VS50988.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

This group shows a single part: AJUSA 85022300.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Valve Stem Seal parts for the 2024 BMW 230I come from 2 brands — AJUSA and MAHLE / CLEVITE.

Part numbers include AJUSA 57067700, AJUSA 12027900 and AJUSA 12028200, among others listed above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

7 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2024 BMW 230I come from 5 brands — VNE, WELLS, GATES and 2 other brands. The "Popular" part is GATES VVS229.

This group includes GATES VVS229, HOLSTEIN 2VTS0370 and ÜRO PARTS 11368696446 and the remaining parts above.

This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2024 BMW 230I — AJUSA 01907000.