2 Ignition parts are listed for the 1963 Bristol 407, in 1 part type, covering the 5.1L V8 engine. Each one has a brand, a manufacturer part number and notes that say where it fits.
On the 1963 Bristol 407, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules. Every listed part is a Distributor Mounting Gasket.
The 1963 Bristol 407 came with a single engine, the 5.1L V8, and every part is verified against it.
2 brands supply ignition parts for the 1963 Bristol 407, led by FEL-PRO (1 part) and VICTOR REINZ (1 part).
Each part number listed for the 1963 Bristol 407 opens a page with every vehicle that part fits.
Distributor Mounting Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO | 6464 | 🇺🇸 US | Distributor mounting gasket and Distributor shaft seal included | View on Amazon |
| VICTOR REINZ | 711387200 | 🇺🇸 US | View on Amazon |
This table covers the gaskets that seal the Distributor Mounting. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
2 Distributor Mounting Gasket parts are listed for the 1963 Bristol 407, from FEL-PRO and VICTOR REINZ.
Listed part numbers: FEL-PRO 6464 and VICTOR REINZ 711387200.
Buying Ignition Parts for a 1963 Bristol 407
On this vehicle, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules.
- Confirm you have the 5.1L V8 engine — every part on this page is matched to it.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Distributor Mounting Gasket .
Frequently Asked Questions
How many ignition parts fit the 1963 Bristol 407?
Our catalog currently lists 2 ignition parts for the 1963 Bristol 407 across 1 subcategory and 2 brands, covering the 5.1L V8 engine. Each part is matched to the engine(s) it fits.
What are the signs of ignition problems on a 1963 Bristol 407?
Common symptoms include misfires under load, rough idle, flashing check-engine light, or poor starting in damp weather. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1963 Bristol 407 was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 1963 Bristol 407?
Every part on this page is matched to the 5.1L V8 engine. Then gap matters even on “pre-gapped” plugs — verify against spec, and replace coil boots when they come off a high-mileage engine. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 1963 Bristol 407
Ignition Parts for Other Bristol 407 Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.