1992 Buick Roadmaster Engine Parts

This table covers the camshafts that open the valves. Read more

This group shows a single part: MELLING CCS39.

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

10 Camshaft Bearing parts for the 1992 Buick Roadmaster come from 3 brands — DURA-BOND, MAHLE / CLEVITE and SEALED POWER. The "Popular" part is DURA-BOND CH8.

This table covers the Camshaft bolts. Read more

GM GENUINE supplies both parts for the 1992 Buick Roadmaster.

Part numbers include GM GENUINE 09424877 and GM GENUINE 14093637.

This table covers the Camshaft bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: CLOYES P9005.

This table covers the Camshaft Dowel pins. Read more

This group shows a single part: GM GENUINE 12554553.

This table covers the Camshaft plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

This group shows a single part: GM GENUINE 10241154.

This table covers the Camshaft Retainer / Thrust plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

4 Camshaft Retainer / Thrust Plate parts are listed for the 1992 Buick Roadmaster, from GM GENUINE, ENGINETECH and MELLING.

Part numbers include ENGINETECH CR5057, GM GENUINE 10168501 and GM GENUINE 10088128, among others listed above.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

30 Connecting Rod Bearing parts for the 1992 Buick Roadmaster come from 5 brands — MAHLE / CLEVITE, ENGINE PRO, SEALED POWER and 2 other brands. The "Popular" part is MAHLE / CLEVITE CB663A. Grades run from High Performance through Standard Replacement; High Performance is the most populated section, led by MAHLE / CLEVITE and ENGINE PRO.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Conversion / Lower Gasket Set parts for the 1992 Buick Roadmaster come from 6 brands — APEX, FEL-PRO, ELRING and 3 other brands. The "Popular" part is APEX ACS3023.

This group includes APEX ACS3023, FEL-PRO CS8510 and ELRING 686130 and the remaining parts above.

This table covers the crankshafts that turn piston motion into rotation. Read more

This group shows a single part: GM GENUINE 12670965.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

17 Crankshaft Main Bearing parts are listed for the 1992 Buick Roadmaster, from MAHLE / CLEVITE, SEALED POWER, ENGINE PRO and 2 other brands. MAHLE / CLEVITE MS909H carries the "Popular" badge.

In the High Performance grade, MAHLE / CLEVITE supplies 4 parts: engineered beyond original-equipment specification. A representative part number is MAHLE / CLEVITE MS909H.

The Standard Replacement section lists 10 options from SEALED POWER, MAHLE / CLEVITE, GM GENUINE and 1 other brand — built to original-equipment specification. MAHLE / CLEVITE MS909A is listed in this group.

3 ungrouped parts are not assigned to a grade, with the same engine-level match.

This table covers the Crankshaft Main Bearing Cap bolts. Read more

This group shows a single part: GM GENUINE 12561388.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

11 Crankshaft Repair Sleeve parts are listed for the 1992 Buick Roadmaster, from TIMKEN, WJB / INMOTION PARTS, NATIONAL and 6 other brands. NATIONAL 99176 carries the "Popular" badge.

This table covers the Crankshaft Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

One part is listed for the 1992 Buick Roadmaster — VICTOR REINZ 711454000.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

25 Crankshaft Seal parts are listed for the 1992 Buick Roadmaster, from NATIONAL, TIMKEN, WJB / INMOTION PARTS and 8 other brands. FEL-PRO BS40520 carries the "Popular" badge.

This table covers the Crankshaft Seal covers. Read more

This group shows a single part: GM GENUINE 14088556.

This table covers the gaskets that seal the Crankshaft Seal. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: GM GENUINE 12555771.

This table covers the Cylinder Head Alignment Dowel pins. Read more

5 Cylinder Head Alignment Dowel Pin parts for the 1992 Buick Roadmaster come from 2 brands — PIONEER and GM GENUINE. The "Popular" part is PIONEER S1110.

Listed part numbers: PIONEER S1110, GM GENUINE 585927 and GM GENUINE 12554848, plus the other parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

6 Cylinder Head Bolt parts for the 1992 Buick Roadmaster come from 5 brands — PIONEER, APEX, FEL-PRO and 2 other brands. The "Popular" part is APEX AHB322.

Listed part numbers: APEX AHB322, FEL-PRO ES72856 and MAHLE / CLEVITE GS33285, plus the other parts above.

This table covers the Cylinder Head Bolt washers. Read more

This group shows a single part: PIONEER S1018.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

10 Cylinder Head Gasket parts for the 1992 Buick Roadmaster come from 7 brands — ENGINETECH, FEL-PRO, APEX and 4 other brands. The "Popular" part is FEL-PRO 7733PT2.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Cylinder Head Gasket Set parts for the 1992 Buick Roadmaster come from 6 brands — FEL-PRO, APEX, ELRING and 3 other brands. The "Popular" part is APEX AHS3023.

Part numbers include APEX AHS3023, FEL-PRO HS7733PT15 and ELRING 685010, among others listed above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 1992 Buick Roadmaster — DORMAN 090067.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 1992 Buick Roadmaster come from 2 brands — MAHLE / CLEVITE and VICTOR REINZ.

This group includes MAHLE / CLEVITE 55138 and VICTOR REINZ 711382900.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

2 Cylinder Repair Sleeve parts for the 1992 Buick Roadmaster come from MELLING.

Part numbers include MELLING CSL167 and MELLING CSL267.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

KAT'S HEATERS supplies the 3 Engine Block Heater parts for the 1992 Buick Roadmaster.

This group includes KAT'S HEATERS 16600, KAT'S HEATERS 11612 and KAT'S HEATERS 13150.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Engine Kit Gasket Set parts for the 1992 Buick Roadmaster come from 6 brands — ENGINE PRO, APEX, FEL-PRO and 3 other brands. The "Popular" part is APEX AFS3023.

Listed part numbers: APEX AFS3023, FEL-PRO 2601269 and ENGINE PRO 311003, plus the other parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

9 Exhaust Valve parts are listed for the 1992 Buick Roadmaster, from QUALCAST, MAHLE / CLEVITE, MELLING and 1 other brand. MELLING V1192 carries the "Popular" badge.

This group includes MELLING V1192, QUALCAST 101192 and GM GENUINE 19435238 and the remaining parts above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

14 Expansion Plug parts for the 1992 Buick Roadmaster come from 5 brands — PIONEER, MELLING, DORMAN and 2 other brands. The "Popular" part is DORMAN 565030.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

7 Harmonic Balancer parts for the 1992 Buick Roadmaster come from 6 brands — ENGINE PRO, SKP, DAYCO and 3 other brands. The "Popular" part is SKP SK594009.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SK594009 is listed in this group.

The High Performance section: 2 options from ENGINE PRO. ENGINE PRO PB1012ST is listed in this group.

Standard Replacement: 4 parts, from DAYCO, ATP, GM GENUINE and 1 other brand. A representative part number is DAYCO PB1200N.

This group includes SKP SK594009, ENGINE PRO PB1012ST and ENGINE PRO PB1012SS and the remaining parts above.

This table covers the Harmonic Balancer bolts. Read more

One part is listed for the 1992 Buick Roadmaster — GM GENUINE 09440024.

This table covers the wear sleeves used to restore a Harmonic Balancer seal surface. Read more

7 Harmonic Balancer Repair Sleeve parts are listed for the 1992 Buick Roadmaster, from NATIONAL, MAHLE / CLEVITE, BCA and 3 other brands. MAHLE / CLEVITE A228 carries the "Popular" badge.

Listed part numbers: MAHLE / CLEVITE A228, NATIONAL 88176 and BCA NS5000, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts for the 1992 Buick Roadmaster come from 5 brands — APEX, FEL-PRO, GM GENUINE and 2 other brands. The "Popular" part is APEX AMS3230.

This group includes APEX AMS3230, FEL-PRO MS93317 and GM GENUINE 19367332 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Intake Valve parts are listed for the 1992 Buick Roadmaster, from QUALCAST, MELLING and MAHLE / CLEVITE. MELLING V1195 carries the "Popular" badge.

Part numbers include MELLING V1195, MAHLE / CLEVITE 2112072 and QUALCAST 101195, among others listed above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

9 Motor Mount parts are listed for the 1992 Buick Roadmaster, from PIONEER, WESTAR, SKP and 4 other brands. ANCHOR 2292 carries the "Popular" badge.

Economy: 1 part, from SKP. A representative part number is SKP SKM2292.

High Performance: 1 part, from ENERGY SUSPENSION. A representative part number is ENERGY SUSPENSION 31116G.

The Standard Replacement section: 7 options from PIONEER, WESTAR, ANCHOR and 2 other brands. ANCHOR 2292 is listed in this group.

This group includes ANCHOR 2292, SKP SKM2292 and ENERGY SUSPENSION 31116G and the remaining parts above.

This table covers the Motor Mount kits. Read more

2 Motor Mount Kit parts are listed for the 1992 Buick Roadmaster, from ANCHOR and ENERGY SUSPENSION.

Part numbers include ANCHOR 300051 and ENERGY SUSPENSION 31130G.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

21 Oil parts are listed for the 1992 Buick Roadmaster, from MOBIL, VALVOLINE and IDEMITSU. MOBIL 125195 carries the "Popular" badge.

In the Full Synthetic grade, MOBIL and VALVOLINE supply 8 parts: full-synthetic oils. A representative part number is MOBIL 125195.

The High Mileage (>75,000 Miles) section lists 8 options from VALVOLINE and MOBIL — oils grouped for high-mileage engines. VALVOLINE VV1556 is listed in this group.

In the Racing grade, IDEMITSU supplies 1 part: grouped under the catalog's "Racing" designation — the notes column spells out what sets them apart. A representative part number is IDEMITSU 30018100750.

In the Synthetic Blend grade, MOBIL and VALVOLINE supply 4 parts: synthetic-blend oils. A representative part number is MOBIL 124406.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: DORMAN 66201.

This table covers the Oil Cooler lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

4 Oil Cooler Line parts are listed for the 1992 Buick Roadmaster, from DORMAN and SUNSONG.

Part numbers include DORMAN 625600, DORMAN 625601 and SUNSONG 5801286, among others listed above.

This table covers the harness connectors at the Oil Cooler Line. Typical signs include an intermittent fault that moves when you wiggle the plug, green corrosion, or a melted housing. Match terminal count and keyway, not just color. Many families look identical and will not lock. Read more

This group shows a single part: DORMAN 800812.

This table covers the Oil Cooler Mounting kits. Read more

2 Oil Cooler Mounting Kit parts for the 1992 Buick Roadmaster come from HAYDEN.

Listed part numbers: HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

One part is listed for the 1992 Buick Roadmaster — PIONEER 500002.