2008 Buick Allure Automatic Transmission Parts

This table covers the Accumulator covers. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24205584.

This table covers the pistons inside a transmission accumulator. Read more

3 Accumulator Piston parts are listed for the 2008 Buick Allure, from TRANSGO and GM GENUINE.

Listed part numbers: GM GENUINE 24206857, TRANSGO 4T654ACM and TRANSGO 4T65ACM.

This table covers the Accumulator Piston pins. Read more

This group shows a single part: GM GENUINE 24203979.

This table covers the Accumulator Piston Seal sleeves. Read more

GM GENUINE supplies both parts for the 2008 Buick Allure.

Part numbers include GM GENUINE 8644917 and GM GENUINE 8678473.

This table covers the Actuator Feed Limit valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: TRANSGO 4T65AFL.

This table covers the control units that command automatic-transmission shifts. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24252114.

This table covers the apply bands inside the automatic transmission. Read more

3 Band parts are listed for the 2008 Buick Allure, from GM GENUINE and ATP.

Listed part numbers: ATP TPB1030, GM GENUINE 24213362 and GM GENUINE 24269117.

This table covers the Band Anchor pins. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 8651798.

This table covers the bushings in this assembly. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

3 Bushing parts for the 2008 Buick Allure come from DURA-BOND.

This group includes DURA-BOND 84061B, DURA-BOND 02399 and DURA-BOND 02399T.

This table covers the Bushing kits. Read more

This group shows a single part: DURA-BOND TK35.

This table covers the gaskets that seal the Case. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

GM GENUINE supplies both parts for the 2008 Buick Allure.

Part numbers include GM GENUINE 24212897 and GM GENUINE 24206391.

This table covers the Clutch Apply plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

GM GENUINE supplies both parts for the 2008 Buick Allure.

This group includes GM GENUINE 24224891 and GM GENUINE 8682801.

This table covers the Clutch housings. Read more

This group shows a single part: GM GENUINE 24236214.

This table covers the Clutch Housing Thrust bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: GM GENUINE 24227685.

This table covers the pistons that apply a clutch pack. Read more

GM GENUINE supplies the 3 Clutch Pack Piston parts for the 2008 Buick Allure.

Listed part numbers: GM GENUINE 24205378, GM GENUINE 24208336 and GM GENUINE 19368340.

This table covers the Clutch plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

GM GENUINE supplies the 7 Clutch Plate parts for the 2008 Buick Allure. GM GENUINE 24281019 carries the "Popular" badge.

The Backing Plate section lists 1 option from GM GENUINE — grouped under the catalog's "Backing Plate" designation — the notes column spells out what sets them apart. GM GENUINE 24204105 is listed in this group.

In the Friction grade, GM GENUINE supplies 6 parts: grouped under the catalog's "Friction" designation — the notes column spells out what sets them apart. A representative part number is GM GENUINE 24281019.

Part numbers include GM GENUINE 24281019, GM GENUINE 24204105 and GM GENUINE 24218248, among others listed above.

This table covers the clutch-plate packs inside the transmission or transfer case. Read more

This group shows a single part: GM GENUINE 24282750.

This table covers the Clutch Seal rings. Read more

3 Clutch Seal Ring parts for the 2008 Buick Allure come from GM GENUINE.

This group includes GM GENUINE 24209498, GM GENUINE 8656342 and GM GENUINE 24213410.

This table covers the detent levers that hold a shifter in gear. Read more

This group shows a single part: GM GENUINE 19369217.

This table covers the seals at the Dipstick / Fluid Filler Tube. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 1259475.

This table covers the Drive Sprocket bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24214158.

This table covers the Extension Housing bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: DURA-BOND GMT67.

This table covers the gaskets that seal the Extension Housing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 8651419.

This table covers the replacement filters for this application — the table heading and notes say which circuit. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

12 Filter parts for the 2008 Buick Allure come from 7 brands — ATP, WIX, HASTINGS / BALDWIN and 4 other brands. The "Popular" part is ATP TF161.

The Economy section lists 2 options from ATP and VARIOUS MFR — the catalog's value-priced group. ATP TF161 is listed in this group.

In the Standard Replacement grade, ATP, WIX, HASTINGS / BALDWIN and 3 other brands supply 10 parts: built to original-equipment specification. A representative part number is GM GENUINE 24227477.

This table covers the seals at the Filter. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 8656613.

This table covers the Fluid Cooler Line hoses. Typical signs include swelling, cracks, a soft spot, or a leak at a clamp. Replace adjacent aged hoses while the system is drained — they share the same heat cycle. Read more

6 Fluid Cooler Line / Hose parts for the 2008 Buick Allure come from 3 brands — GM GENUINE, DORMAN and SKP. The "Popular" part is GM GENUINE 15264590.

Listed part numbers: GM GENUINE 15264590, GM GENUINE 15264597 and DORMAN 624122, plus the other parts above.

This table covers the harness connectors at the Fluid Cooler Line / Hose. Typical signs include an intermittent fault that moves when you wiggle the plug, green corrosion, or a melted housing. Match terminal count and keyway, not just color. Many families look identical and will not lock. Read more

3 Fluid Cooler Line / Hose Connector parts are listed for the 2008 Buick Allure, from FOUR SEASONS, GM GENUINE and HAYDEN.

Listed part numbers: FOUR SEASONS 53024, GM GENUINE 24236555 and HAYDEN 397.

This table covers the Fluid Cooler Line clips. Read more

This group shows a single part: GM GENUINE 24205103.

This table covers the pans that hold automatic-transmission fluid. Read more

4 Fluid Pan parts are listed for the 2008 Buick Allure, from DORMAN, GM GENUINE, SKP and 1 other brand.

Part numbers include DORMAN 265814, GM GENUINE 24206181 and SKP SK265814, among others listed above.

This table covers the gaskets that seal the Fluid Pan. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Fluid Pan Gasket parts for the 2008 Buick Allure come from 2 brands — GM GENUINE and MAHLE / CLEVITE.

Part numbers include GM GENUINE 24206182 and MAHLE / CLEVITE W32865.

This table covers the Fluid Pan magnets. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 29535617.

This table covers the Fluid Pump Cover bolts. Read more

This group shows a single part: GM GENUINE 24210075.

This table covers the seals at the Fluid Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Buick Allure — SKF 17849.

This table covers the Fluid Pump shafts. Read more

This group shows a single part: GM GENUINE 24209284.

This table covers the Fluid temperature sensors. Typical signs include hard cold starts, a fan that never comes on, or a gauge that disagrees with the scan tool. A sensor that reads open or shorted is usually the part; an implausible-but-smooth reading can be wiring. Read more

3 Fluid Temperature Sensor parts for the 2008 Buick Allure come from 3 brands — GM GENUINE, STANDARD MOTOR PRODUCTS and WELLS.

Part numbers include GM GENUINE 12129691, STANDARD MOTOR PRODUCTS TX220 and WELLS 5S8219.

This table covers the seals at the Manual Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24236395.

This table covers the wear sleeves used to restore a Output Shaft seal surface. Read more

2 Output Shaft Repair Sleeve parts for the 2008 Buick Allure come from 2 brands — BCA and SKF.

Part numbers include BCA NS99139 and SKF 99138.

This table covers the seals at the Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Output Shaft Seal parts for the 2008 Buick Allure come from 4 brands — SKF, BCA, SCHAEFFLER and 1 other brand. The "Popular" part is SKF 13750.

This group includes SKF 13750, BCA NS3543 and SCHAEFFLER SS60801 and the remaining parts above.

This table covers the parking pawls that lock the transmission in Park. Read more

This group shows a single part: GM GENUINE 24237506.

This table covers the Plug adapters. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 8654382.

This table covers the Pressure Control (EPC) solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Pressure Control (EPC) Solenoid parts for the 2008 Buick Allure come from 2 brands — GM GENUINE and STANDARD MOTOR PRODUCTS.

This group includes GM GENUINE 24225825 and STANDARD MOTOR PRODUCTS TCS96.

This table covers the Pressure Switch manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

One part is listed for the 2008 Buick Allure — ATP JE44.

This table covers the Reaction Carrier Thrust bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 8646504.

This table covers the rebuild kits for this assembly. Read more

3 Rebuild Kit parts are listed for the 2008 Buick Allure, from ATP, PIONEER and TRANSTEC.

In the Deluxe Kit (Master Kit + Filter, Band & Common Bushings) grade, ATP and PIONEER supply 2 parts: grouped under the catalog's "Deluxe Kit (Master Kit + Filter, Band & Common Bushings)" designation — the notes column spells out what sets them apart. A representative part number is ATP PMS120.

In the Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings) grade, TRANSTEC supplies 1 part: grouped under the catalog's "Overhaul Kit (Gaskets, Seals, O-Rings & Sealing Rings)" designation — the notes column spells out what sets them apart. A representative part number is TRANSTEC 81000144.

Part numbers include ATP PMS120, PIONEER 753079 and TRANSTEC 81000144.

This table covers the Retaining rings. Read more

GM GENUINE supplies the 4 Retaining Ring parts for the 2008 Buick Allure.

Part numbers include GM GENUINE 24204373, GM GENUINE 24211765 and GM GENUINE 8631028, among others listed above.

This table covers the seals at the Servo Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

GM GENUINE supplies both parts for the 2008 Buick Allure.

Listed part numbers: GM GENUINE 24204374 and GM GENUINE 24235894.

This table covers the seals at the Servo Piston. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

GM GENUINE supplies the 3 Servo Piston Seal parts for the 2008 Buick Allure.

Listed part numbers: GM GENUINE 24210904, GM GENUINE 8651541 and GM GENUINE 24208959.

This table covers the Shift cables. Typical signs include a stretched or frayed cable, or a control that no longer reaches the end of its travel. Route the new cable through the same clips. A kinked cable binds and fails early. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 25940463.

This table covers the Shift Improvement kits. Read more

2 Shift Improvement Kit parts for the 2008 Buick Allure come from TRANSGO.

This group includes TRANSGO SK4T65E and TRANSGO SK4T60EJR.

This table covers the Shift Interlock solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Shift Interlock Solenoid parts for the 2008 Buick Allure come from 2 brands — DORMAN and GM GENUINE.

This group includes DORMAN 924975 and GM GENUINE 26097679.

This table covers the Shift Linkage bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2008 Buick Allure — DORMAN 14104.

This table covers the wear sleeves used to restore a Shift Shaft seal surface. Read more

3 Shift Shaft Repair Sleeve parts are listed for the 2008 Buick Allure, from SKF and SCHAEFFLER.

Part numbers include SCHAEFFLER SR3451, SKF 480050 and SKF 99050.

This table covers the seals at the Shift Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Buick Allure — SKF 4912.

This table covers the Shift solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

10 Shift Solenoid parts are listed for the 2008 Buick Allure, from PIONEER, STANDARD MOTOR PRODUCTS, ATP and 2 other brands. GM GENUINE 24219819 carries the "Popular" badge.

This table covers the seals at the Side Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24206959.

This table covers the Sun Gear bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2008 Buick Allure — DURA-BOND GMT61.

This table covers the Torque converters. Typical signs include a sulfur smell, rattling substrate, or an efficiency code. Confirm CARB vs Federal certification in the notes before ordering. Read more

This group shows a single part: TC REMANUFACTURING B21JSFM.

This table covers the Torque Converter bolts. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 11588468.

This table covers the Torque Converter Clutch solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Torque Converter Clutch Solenoid parts for the 2008 Buick Allure come from 2 brands — ATP and PIONEER.

This group includes ATP JE8 and PIONEER 771060.

This table covers the Torque Converter Pulse Width Modulation (PWM) solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24227747.

This table covers the seals at the Torque Converter Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24232006.

This table covers the automatic-transmission fluids specified for this gearbox. Typical signs include harsh or delayed shifts, fluid that smells burnt, or a shudder at light throttle. Use exactly the specification in the notes. Automatic transmissions are unforgiving of the wrong fluid. Read more

4 Transmission Fluid parts for the 2008 Buick Allure come from 2 brands — PENTOSIN and VALVOLINE.

In the ATF 64 grade, PENTOSIN supplies 2 parts: grouped under the catalog's "ATF 64" designation — the notes column spells out what sets them apart. A representative part number is PENTOSIN 1058113.

The Dexron section lists 2 options from VALVOLINE — grouped under the catalog's "Dexron" designation — the notes column spells out what sets them apart. VALVOLINE 822405 is listed in this group.

This group includes PENTOSIN 1058113, PENTOSIN 1058215 and VALVOLINE 822405 and the remaining parts above.

This table covers the conditioners and additives used with this transmission fluid. Read more

6 Transmission Fluid Additive parts for the 2008 Buick Allure come from LUBEGARD. The "Popular" part is LUBEGARD 19610.

This group includes LUBEGARD 19610, LUBEGARD 60902 and LUBEGARD 19689 and the remaining parts above.

This table covers the mounts that hold the transmission to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

3 Transmission Mount parts are listed for the 2008 Buick Allure, from ANCHOR, DEA / MARMON RIDE CONTROL and WESTAR.

This group includes ANCHOR 3187, DEA / MARMON RIDE CONTROL A5402 and WESTAR EM2990.

This table covers the Turbine Shaft Fluid Seal rings. Read more

2 Turbine Shaft Fluid Seal Ring parts for the 2008 Buick Allure come from GM GENUINE.

Part numbers include GM GENUINE 8643058 and GM GENUINE 24208978.

This table covers the seals at the Turbine Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: GM GENUINE 8662686.

This table covers the Valve Body covers. Read more

One part is listed for the 2008 Buick Allure — GM GENUINE 24211955.

This table covers the gaskets that seal the Valve Body Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: GM GENUINE 24205119.

This table covers the Valve Body Separator plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

GM GENUINE supplies both parts for the 2008 Buick Allure.

This group includes GM GENUINE 24243102 and GM GENUINE 24244403.