3 Ignition parts are listed for the 1983 Datsun Pickup, in 2 part types, covering the 1.6L L4 engine. Each one has a brand, a manufacturer part number and notes that say where it fits.
On the 1983 Datsun Pickup, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules. All 3 listed parts are Distributor Cap (2 parts) and Condenser / Capacitor (1 part).
Every part on this page is matched to the 1.6L L4 — the only engine offered in the 1983 Datsun Pickup.
The most listed brands for 1983 Datsun Pickup ignition parts are WELLS (2 parts) and JAPANESE OE (1 part).
Each part number listed for the 1983 Datsun Pickup opens a page with every vehicle that part fits.
Condenser / Capacitor
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| WELLS | 5H1049 | 🇲🇽 MX | Standard Duty | View on Amazon |
This table covers the capacitors used in this electrical or A/C circuit.
One part is listed for the 1983 Datsun Pickup — WELLS 5H1049.
Distributor Cap
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| JAPANESE OE | YD220 | 🇲🇽 MX | YEC FLAMMA | View on Amazon |
| WELLS | 5D1077 | 🇲🇽 MX | Distributor Cap Contacts Material: Aluminum | View on Amazon |
This table covers the Distributor caps. Typical signs include a leak at the neck, a cap that will not hold pressure, or a missing tether. Match the pressure rating or thread in the notes — radiator, reservoir and fuel caps are not interchangeable.
2 Distributor Cap parts for the 1983 Datsun Pickup come from 2 brands — JAPANESE OE and WELLS.
Part numbers include JAPANESE OE YD220 and WELLS 5D1077.
Buying Ignition Parts for a 1983 Datsun Pickup
On this vehicle, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules.
- Confirm you have the 1.6L L4 engine — every part on this page is matched to it.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Distributor Cap and Condenser / Capacitor .
Frequently Asked Questions
How many ignition parts fit the 1983 Datsun Pickup?
Our catalog currently lists 3 ignition parts for the 1983 Datsun Pickup across 2 subcategories and 2 brands, covering the 1.6L L4 engine. Each part is matched to the engine(s) it fits.
What are the signs of ignition problems on a 1983 Datsun Pickup?
Common symptoms include misfires under load, rough idle, flashing check-engine light, or poor starting in damp weather. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1983 Datsun Pickup was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 1983 Datsun Pickup?
Every part on this page is matched to the 1.6L L4 engine. Then gap matters even on “pre-gapped” plugs — verify against spec, and replace coil boots when they come off a high-mileage engine. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 1983 Datsun Pickup
Ignition Parts for Other Datsun Pickup Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.