2008 Dodge H100 Engine Parts

This table covers the Balance Shaft Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: CLOYES 95108.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

2 Camshaft Repair Sleeve parts for the 2008 Dodge H100 come from 2 brands — SCHAEFFLER and SKF.

This group includes SCHAEFFLER SR3472 and SKF 99139.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Camshaft Seal parts for the 2008 Dodge H100 come from 4 brands — AJUSA, MAHLE / CLEVITE, SCHAEFFLER and 1 other brand.

Listed part numbers: AJUSA 15013300, MAHLE / CLEVITE 67698 and SCHAEFFLER SS2449, plus the other parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2008 Dodge H100 — AJUSA 54133400.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

2 Crankshaft Repair Sleeve parts for the 2008 Dodge H100 come from 2 brands — SCHAEFFLER and SKF.

Part numbers include SCHAEFFLER SR3549 and SKF 99315.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Crankshaft Seal parts for the 2008 Dodge H100 come from 3 brands — AJUSA, SCHAEFFLER and SKF.

Part numbers include AJUSA 15020600, AJUSA 15035600 and SCHAEFFLER SS3345, among others listed above.

This table covers the bolts that clamp the cylinder head to the block. Read more

One part is listed for the 2008 Dodge H100 — AJUSA 81057200.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

AJUSA supplies the 3 Cylinder Head Gasket parts for the 2008 Dodge H100.

Part numbers include AJUSA 10159300, AJUSA 10159310 and AJUSA 10159320.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2008 Dodge H100 — AJUSA 53019000.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2008 Dodge H100 — AJUSA 51023600.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: QUALCAST 103187.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2008 Dodge H100 — AJUSA 13174500.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: QUALCAST 103186.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

This group shows a single part: WESTAR EM90012.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

3 Oil parts for the 2008 Dodge H100 come from VALVOLINE.

Part numbers include VALVOLINE 797975, VALVOLINE 881159 and VALVOLINE 881042.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 2008 Dodge H100.

Part numbers include HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

5 Oil Drain Plug parts for the 2008 Dodge H100 come from 3 brands — DORMAN, AGS and SKP. The "Popular" part is DORMAN 090053.

Listed part numbers: DORMAN 090053, AGS ODP00007 and DORMAN 090033, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

This group shows a single part: MOTORAD MO100.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

3 Oil Filter parts for the 2008 Dodge H100 come from 3 brands — VARIOUS MFR, MAHLE / CLEVITE and WIX.

The Economy section lists 1 option from VARIOUS MFR — the catalog's value-priced group. VARIOUS MFR PG4750 is listed in this group.

In the Standard Replacement grade, MAHLE / CLEVITE and WIX supply 2 parts: built to original-equipment specification. A representative part number is MAHLE / CLEVITE OC540.

This group includes VARIOUS MFR PG4750, MAHLE / CLEVITE OC540 and WIX WL10031.

This table covers the rings that seal each piston to the cylinder wall. Read more

One part is listed for the 2008 Dodge H100 — HASTINGS MANUFACTURING 2D5666.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: CLOYES 95107.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts for the 2008 Dodge H100 come from 2 brands — SCHAEFFLER and SKF.

Listed part numbers: SCHAEFFLER SS3760 and SKF 17154.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 56013700.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

2 Valve Guide parts for the 2008 Dodge H100 come from QUALCAST.

Listed part numbers: QUALCAST 307850 and QUALCAST 307851.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: AJUSA 57023700.