2009 Dodge Nitro Engine Parts

This table covers the gaskets that seal the Camshaft Housing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2009 Dodge Nitro — FEL-PRO ES73216.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

5 Camshaft Repair Sleeve parts for the 2009 Dodge Nitro come from 5 brands — SKF, BCA, NATIONAL and 2 other brands. The "Popular" part is SKF 99146.

This group includes SKF 99146 and BCA NS99146 and the remaining parts above.

This table covers the Camshaft Retainer / Thrust plates. Typical signs include warpage, cracks, or a plate that no longer locates the assembly. Confirm which plate the notes describe — backing plates, clutch plates and strike plates are different parts. Read more

This group shows a single part: MOPAR 4556518AB.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

13 Camshaft Seal parts for the 2009 Dodge Nitro come from 12 brands — MOPAR, APEX, FEL-PRO and 9 other brands. The "Popular" part is APEX ATC2360.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Connecting Rod Bearing parts are listed for the 2009 Dodge Nitro, from MAHLE / CLEVITE, ENGINETECH and SEALED POWER.

This group includes ENGINETECH BB139J, MAHLE / CLEVITE CB1881A6 and MAHLE / CLEVITE CB1881A and the remaining parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Conversion / Lower Gasket Set parts are listed for the 2009 Dodge Nitro, from ENGINETECH, FEL-PRO, AJUSA and 4 other brands. ENGINETECH CR241CSA carries the "Popular" badge.

Listed part numbers: ENGINETECH CR241CSA, FEL-PRO CS95052 and AJUSA 54165400, plus the other parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Crankshaft Main Bearing parts for the 2009 Dodge Nitro come from 3 brands — ENGINETECH, MAHLE / CLEVITE and MOPAR.

Part numbers include ENGINETECH BC508J, MAHLE / CLEVITE MS2303A and MOPAR 68002265AA.

This table covers the gaskets that seal the Crankshaft Main Bearing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2009 Dodge Nitro — ULTRA-POWER BS40734.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts for the 2009 Dodge Nitro come from 3 brands — SCHAEFFLER, TIMKEN and WJB / INMOTION PARTS.

This group includes SCHAEFFLER SR3462, TIMKEN KWK99112 and WJB / INMOTION PARTS WS99112.

This table covers the Crankshaft Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

This group shows a single part: VICTOR REINZ 711457400.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

21 Crankshaft Seal parts for the 2009 Dodge Nitro come from 10 brands — FEL-PRO, APEX, VICTOR REINZ and 7 other brands. The "Popular" part is BCA NS3638.

This table covers the bolts that clamp the cylinder head to the block. Read more

5 Cylinder Head Bolt parts are listed for the 2009 Dodge Nitro, from FEL-PRO, APEX, ENGINETECH and 2 other brands. FEL-PRO ES72895 carries the "Popular" badge.

This group includes FEL-PRO ES72895, APEX AHB236 and ENGINETECH HB209 and the remaining parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

13 Cylinder Head Gasket parts are listed for the 2009 Dodge Nitro, from APEX, FEL-PRO, ELRING and 4 other brands. APEX AHG280L carries the "Popular" badge.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

9 Cylinder Head Gasket Set parts are listed for the 2009 Dodge Nitro, from ENGINETECH, FEL-PRO, VICTOR REINZ and 3 other brands. ENGINETECH CR241HSA carries the "Popular" badge.

Listed part numbers: ENGINETECH CR241HSA, ENGINETECH CR241HSAWB and AJUSA 52424700, plus the other parts above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

This group shows a single part: MOPAR 4556020AB.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts are listed for the 2009 Dodge Nitro, from ENGINETECH and SBI.

Part numbers include ENGINETECH CHS1060 and SBI 2302165.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

This group shows a single part: MOPAR 4609325.

This table covers the Engine covers. Read more

3 Engine Cover parts are listed for the 2009 Dodge Nitro, from TECHPRO and MOPAR.

Listed part numbers: MOPAR 55197310AF, TECHPRO CH1228111 and TECHPRO CH1228123.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts are listed for the 2009 Dodge Nitro, from AJUSA and ENGINETECH.

This group includes AJUSA 50388100 and ENGINETECH CR215K7.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts for the 2009 Dodge Nitro come from 5 brands — SKP, ENGINETECH, MAHLE / CLEVITE and 2 other brands. The "Popular" part is SKP SKV2787.

Part numbers include SKP SKV2787, ENGINETECH V2787 and MAHLE / CLEVITE 2113214, among others listed above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 2009 Dodge Nitro — MELLING MPE831R.

This table covers the Intake manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

This group shows a single part: MOPAR 4593578AD.

This table covers the Intake Manifold actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

One part is listed for the 2009 Dodge Nitro — MOPAR 4593676AC.

This table covers the Intake Manifold bolts. Read more

One part is listed for the 2009 Dodge Nitro — MOPAR 6104124AA.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Intake Manifold Gasket parts are listed for the 2009 Dodge Nitro, from MAHLE / CLEVITE, APEX, FEL-PRO and 2 other brands. APEX AMS2801 carries the "Popular" badge.

Part numbers include APEX AMS2801, FEL-PRO MS921651 and MAHLE / CLEVITE MS16210B, among others listed above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Plenum Gasket parts for the 2009 Dodge Nitro come from 5 brands — FEL-PRO, APEX, MAHLE / CLEVITE and 2 other brands. The "Popular" part is FEL-PRO MS96324.

This group includes FEL-PRO MS96324, APEX AMS2800 and MAHLE / CLEVITE MS19537 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

6 Intake Valve parts for the 2009 Dodge Nitro come from 6 brands — MELLING, SKP, ENGINETECH and 3 other brands. The "Popular" part is MELLING V1901.

Listed part numbers: MELLING V1901, SKP SKV1901 and ENGINETECH V3408, plus the other parts above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

7 Oil parts for the 2009 Dodge Nitro come from 3 brands — VALVOLINE, IDEMITSU and MOBIL. The "Popular" part is VALVOLINE 797578.

The Conventional section lists 3 options from VALVOLINE — grouped under the catalog's "Conventional" designation — the notes column spells out what sets them apart. VALVOLINE 797578 is listed in this group.

The Full Synthetic section lists 3 options from IDEMITSU — full-synthetic oils. IDEMITSU 30015204750 is listed in this group.

The Synthetic Blend section lists 1 option from MOBIL — synthetic-blend oils. MOBIL 124406 is listed in this group.

Listed part numbers: VALVOLINE 797578, VALVOLINE 881156 and VALVOLINE 881046, plus the other parts above.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

4 Oil Cooler parts for the 2009 Dodge Nitro come from 3 brands — MOPAR, DORMAN and VEMO.

This group includes DORMAN 918898, MOPAR 4892422AA and MOPAR 4892259AA and the remaining parts above.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 2009 Dodge Nitro.

This group includes HAYDEN 238 and HAYDEN 153.

This table covers the Oil Dipstick tubes. Read more

3 Oil Dipstick / Tube parts for the 2009 Dodge Nitro come from 2 brands — MOPAR and DORMAN.

Part numbers include DORMAN 921188, MOPAR 4593604AA and MOPAR 4892268AA.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts for the 2009 Dodge Nitro come from 4 brands — DORMAN, AGS, MOPAR and 1 other brand. The "Popular" part is AGS ODP00007.

Part numbers include AGS ODP00007, DORMAN 090053 and DORMAN 090115, among others listed above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts are listed for the 2009 Dodge Nitro, from APEX, FEL-PRO, MAHLE / CLEVITE and 1 other brand.

Part numbers include APEX ADP1902, FEL-PRO 70822 and MAHLE / CLEVITE 2051, among others listed above.

This table covers the caps on the oil filler neck. Read more

5 Oil Filler Cap parts for the 2009 Dodge Nitro come from 5 brands — MOTORAD, CALORSTAT, GATES and 2 other brands. The "Popular" part is MOTORAD MO158.

Part numbers include MOTORAD MO158, CALORSTAT OC2334 and GATES 31299, among others listed above.

This table covers the Oil Filler tubes. Read more

2 Oil Filler Tube parts for the 2009 Dodge Nitro come from MOPAR.

Part numbers include MOPAR 4892264AA and MOPAR 53013906AB.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

18 Oil Filter parts for the 2009 Dodge Nitro come from 14 brands — VARIOUS MFR, WIX, ACDELCO and 11 other brands. The "Popular" part is WIX 57060XP.

The Economy section lists 5 options from FRAM, FVP, PRO-TEC and 2 other brands — the catalog's value-priced group. FRAM FE10060 is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 57060XP is listed in this group.

In the Standard Replacement grade, ACDELCO, MOPAR, BOSCH and 6 other brands supply 11 parts: built to original-equipment specification. A representative part number is ACDELCO PF48.

This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: MOPAR 5003905AA.

This table covers the oil pans that hold the engine's oil sump. Read more

One part is listed for the 2009 Dodge Nitro — MOPAR 4892228AB.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts for the 2009 Dodge Nitro come from 5 brands — FEL-PRO, APEX, MAHLE / CLEVITE and 2 other brands. The "Popular" part is FEL-PRO OS30754R.

Listed part numbers: FEL-PRO OS30754R, APEX AOP280A and MAHLE / CLEVITE OS32285, plus the other parts above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

3 Oil Pump parts for the 2009 Dodge Nitro come from 3 brands — ENGINETECH, MELLING and MOPAR.

The Economy section: 1 option from ENGINETECH. ENGINETECH EPK156 is listed in this group.

Standard Replacement: 2 parts, from MELLING and MOPAR. A representative part number is MELLING M521.

Listed part numbers: ENGINETECH EPK156, MELLING M521 and MOPAR 4663844BA.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2009 Dodge Nitro — MOPAR 4648938AC.

This table covers the seals at the Oil Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2009 Dodge Nitro — MOPAR 4659945.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

4 Piston parts are listed for the 2009 Dodge Nitro, from ENGINETECH and MAHLE / CLEVITE.

Listed part numbers: ENGINETECH P6021, ENGINETECH K60216P and MAHLE / CLEVITE 2243778, plus the other parts above.

This table covers the rings that seal each piston to the cylinder wall. Read more

6 Piston Ring parts are listed for the 2009 Dodge Nitro, from HASTINGS MANUFACTURING, ENGINETECH, MAHLE / CLEVITE and 1 other brand. ENGINETECH C96046 carries the "Popular" badge.

The Premium section lists 4 options from ENGINETECH, HASTINGS MANUFACTURING, MAHLE / CLEVITE and 1 other brand — a step above OE specification in materials, tolerances or warranty terms. ENGINETECH C96046 is listed in this group.

The Standard Replacement section: 2 options from HASTINGS MANUFACTURING. HASTINGS MANUFACTURING 2C4890 is listed in this group.

Part numbers include ENGINETECH C96046, HASTINGS MANUFACTURING 2M4890S and MAHLE / CLEVITE 41856CP, among others listed above.

This table covers the rocker arms that transfer cam motion to the valves. Read more

3 Rocker Arm parts for the 2009 Dodge Nitro come from ENGINETECH.

Part numbers include ENGINETECH ER910, ENGINETECH ER911 and ENGINETECH ER909.

This table covers the Rocker Arm shafts. Read more

2 Rocker Arm Shaft parts for the 2009 Dodge Nitro come from MOPAR.

Part numbers include MOPAR 4315823 and MOPAR 4663998.

This table covers the Spring retainers. Read more

MOPAR supplies the 3 Spring Retainer parts for the 2009 Dodge Nitro.

This group includes MOPAR 52108058AA, MOPAR 52108138AB and MOPAR 52108203AA.

This table covers the Thrust washers. Read more

2 Thrust Washer parts for the 2009 Dodge Nitro come from 2 brands — ENGINETECH and MAHLE / CLEVITE.

Part numbers include ENGINETECH TW508 and MAHLE / CLEVITE TW695S.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

10 Timing Belt parts are listed for the 2009 Dodge Nitro, from CLOYES, ENGINETECH, ULTRA-POWER and 7 other brands. DAYCO 95295 carries the "Popular" badge.

Economy: 3 parts, from CLOYES, ENGINETECH and ULTRA-POWER. A representative part number is CLOYES B295.

The Standard Replacement section: 7 options from DAYCO, GATES, ACDELCO and 4 other brands. DAYCO 95295 is listed in this group.

This table covers the Timing Belt & component kits. Read more

15 Timing Belt & Component Kit parts for the 2009 Dodge Nitro come from 8 brands — DAYCO, CONTINENTAL, GATES and 5 other brands. The "Popular" part is CONTINENTAL PP295LK3.

The Economy section: 1 option from CLOYES. CLOYES BK295A is listed in this group.

Standard Replacement: 14 parts, from DAYCO, CONTINENTAL, GATES and 4 other brands. A representative part number is CONTINENTAL PP295LK3.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

5 Timing Belt Pulley parts for the 2009 Dodge Nitro come from 5 brands — DAYCO, ACDELCO, CLOYES and 2 other brands. The "Popular" part is DAYCO 84086.

This group includes DAYCO 84086, ACDELCO T43197 and CLOYES 95554 and the remaining parts above.