1960 Edsel Villager Engine Parts

This table covers the camshafts that open the valves. Read more

2 Camshaft parts for the 1960 Edsel Villager come from MELLING.

Part numbers include MELLING SYB2 and MELLING SYB8.

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Camshaft Bearing parts for the 1960 Edsel Villager come from 2 brands — SEALED POWER and KING ENGINE BEARINGS.

Part numbers include KING ENGINE BEARINGS CS539BB, KING ENGINE BEARINGS CS515BB and SEALED POWER 1160M, among others listed above.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

11 Connecting Rod Bearing parts for the 1960 Edsel Villager come from 3 brands — MAHLE / CLEVITE, SEALED POWER and KING ENGINE BEARINGS. The "Popular" part is MAHLE / CLEVITE CB760P.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Crankshaft Main Bearing parts are listed for the 1960 Edsel Villager, from KING ENGINE BEARINGS, MAHLE / CLEVITE and SEALED POWER.

This group includes KING ENGINE BEARINGS MB583AM, KING ENGINE BEARINGS MB559AM and MAHLE / CLEVITE MS178P and the remaining parts above.

This table covers the gaskets that seal the Crankshaft Main Bearing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: VICTOR REINZ 181002501.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

4 Crankshaft Repair Sleeve parts are listed for the 1960 Edsel Villager, from BCA, NATIONAL, SCHAEFFLER and 1 other brand.

This group includes BCA NS88187, NATIONAL 99187 and SCHAEFFLER SR3506 and the remaining parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

12 Crankshaft Seal parts are listed for the 1960 Edsel Villager, from FEL-PRO, MAHLE / CLEVITE, NATIONAL and 3 other brands. FEL-PRO BS6141 carries the "Popular" badge.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts for the 1960 Edsel Villager come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO 7999PT, FEL-PRO 8554PT and MAHLE / CLEVITE 1176TC and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts for the 1960 Edsel Villager come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO HS7999PT3, FEL-PRO HS8554PT and MAHLE / CLEVITE HS1176VJ and the remaining parts above.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 1960 Edsel Villager come from 2 brands — FEL-PRO and VICTOR REINZ.

Part numbers include FEL-PRO 8554SP and VICTOR REINZ 711383000.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Engine Kit Gasket Set parts for the 1960 Edsel Villager come from 3 brands — FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE.

This group includes FEL-PRO FS7999PT3, FEL-PRO 2601035 and FEL-PRO FS8554PT and the remaining parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts are listed for the 1960 Edsel Villager, from MELLING, QUALCAST and MAHLE / CLEVITE.

Listed part numbers: MAHLE / CLEVITE 2111939, MELLING V0375 and MELLING V1242, plus the other parts above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

4 Expansion Plug parts for the 1960 Edsel Villager come from QUALCAST.

Listed part numbers: QUALCAST 9720, QUALCAST 9720B and QUALCAST 9719, plus the other parts above.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

2 Harmonic Balancer parts for the 1960 Edsel Villager come from ENGINE PRO.

This group includes ENGINE PRO PB1111ST and ENGINE PRO PB1111SS.

This table covers the wear sleeves used to restore a Harmonic Balancer seal surface. Read more

5 Harmonic Balancer Repair Sleeve parts are listed for the 1960 Edsel Villager, from MAHLE / CLEVITE, BCA, NATIONAL and 1 other brand.

Part numbers include BCA NS88187, MAHLE / CLEVITE A2291 and MAHLE / CLEVITE A2262, among others listed above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts for the 1960 Edsel Villager come from 3 brands — FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE.

Listed part numbers: FEL-PRO MS9361B1, FEL-PRO MS90145 and MAHLE / CLEVITE MS15166X, plus the other parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

2 Intake Valve parts are listed for the 1960 Edsel Villager, from QUALCAST and SEALED POWER.

Listed part numbers: QUALCAST 10376 and SEALED POWER V1128.

This table covers the drain plugs in the oil pan. Read more

One part is listed for the 1960 Edsel Villager — DORMAN 090005.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Drain Plug Gasket parts for the 1960 Edsel Villager come from 2 brands — FEL-PRO and VICTOR REINZ.

Part numbers include FEL-PRO 70822 and VICTOR REINZ 711346200.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

13 Oil Filter parts are listed for the 1960 Edsel Villager, from CHAMP / LUBER-FINER, WIX, FRAM and 7 other brands. WIX 51515XP carries the "Popular" badge.

In the Economy grade, CHAMP / LUBER-FINER, FVP, PRO-TEC and 2 other brands supply 6 parts: the catalog's value-priced group. A representative part number is CHAMP / LUBER-FINER PH400.

In the High Performance / Heavy Duty grade, WIX, FRAM and MOBIL supply 3 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 51515XP.

The Standard Replacement section lists 4 options from MOTORCRAFT, WIX, ACDELCO and 1 other brand — built to original-equipment specification. MOTORCRAFT FL1A is listed in this group.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: FEL-PRO 70135.

This table covers the gaskets that seal the Oil Filter. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Filter Gasket parts for the 1960 Edsel Villager come from 2 brands — MAHLE / CLEVITE and VICTOR REINZ.

Part numbers include MAHLE / CLEVITE B25451 and VICTOR REINZ 711387600.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Oil Pan Gasket parts are listed for the 1960 Edsel Villager, from FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE. FEL-PRO OS11701D carries the "Popular" badge.

This group includes FEL-PRO OS11701D, FEL-PRO OS10701C1 and FEL-PRO OS11701C and the remaining parts above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

8 Oil Pump parts are listed for the 1960 Edsel Villager, from MELLING, SEALED POWER and SKP. MELLING M57HV carries the "Popular" badge.

Economy: 1 part, from SKP. A representative part number is SKP SKPM57.

In the High Volume / Pressure grade, MELLING and SEALED POWER supply 4 parts: grouped under the catalog's "High Volume / Pressure" designation — the notes column spells out what sets them apart. A representative part number is MELLING M57HV.

The Standard Replacement section: 2 options from MELLING and SEALED POWER. MELLING M57 is listed in this group.

1 ungrouped part is not assigned to a grade, with the same engine-level match.

Listed part numbers: MELLING M57HV, SKP SKPM57 and MELLING M57HP, plus the other parts above.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Pump Gasket parts for the 1960 Edsel Villager come from 2 brands — FEL-PRO and VICTOR REINZ.

This group includes FEL-PRO 10784, FEL-PRO 11792 and VICTOR REINZ 711450400 and the remaining parts above.

This table covers the gaskets that seal the Oil Pump Pickup Tube. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Pump Pickup Tube Gasket parts for the 1960 Edsel Villager come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO 72516, MAHLE / CLEVITE B26151 and VICTOR REINZ 711350300.

This table covers the Oil Pump repair kits. Read more

This group shows a single part: MELLING K56.

This table covers the Oil Pump shafts. Read more

3 Oil Pump Shaft parts are listed for the 1960 Edsel Villager, from MELLING and SEALED POWER.

Part numbers include MELLING IS42, MELLING IS60 and SEALED POWER 22461114.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

5 Piston parts for the 1960 Edsel Villager come from 2 brands — SEALED POWER and SILV-O-LITE.

In the Premium grade, SEALED POWER supplies 1 part: a step above OE specification in materials, tolerances or warranty terms. A representative part number is SEALED POWER 246CP.

Standard Replacement: 2 parts, from SEALED POWER. A representative part number is SEALED POWER 246NP.

2 further parts sit outside the graded sections, with the same engine-level match.

This group includes SEALED POWER 246CP, SEALED POWER 246NP and SEALED POWER 246AP and the remaining parts above.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 1960 Edsel Villager — MAHLE / CLEVITE 2233608.

This table covers the rings that seal each piston to the cylinder wall. Read more

12 Piston Ring parts for the 1960 Edsel Villager come from 2 brands — HASTINGS MANUFACTURING and SEALED POWER. The "Popular" part is HASTINGS MANUFACTURING 568.

Premium: 4 parts, from HASTINGS MANUFACTURING and SEALED POWER. A representative part number is HASTINGS MANUFACTURING 2M568.

Standard Replacement: 8 parts, from HASTINGS MANUFACTURING and SEALED POWER. A representative part number is HASTINGS MANUFACTURING 568.

This table covers the pushrods that transfer lifter motion to the rocker arms. Read more

6 Push Rod parts for the 1960 Edsel Villager come from 2 brands — MELLING and QUALCAST. The "Popular" part is MELLING MPR311.

This group includes MELLING MPR311, MELLING MPR73 and MELLING MPR311A and the remaining parts above.

This table covers the Push Rod Cover gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

This group shows a single part: FEL-PRO PS10700C.

This table covers the Push Rod Cover grommets. Read more

This group shows a single part: FEL-PRO 10740.

This table covers the Push Rod gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Push Rod Gasket Set parts are listed for the 1960 Edsel Villager, from VICTOR REINZ and MAHLE / CLEVITE.

Part numbers include MAHLE / CLEVITE PS38524, VICTOR REINZ 181004501 and VICTOR REINZ 181005401.

This table covers the rocker arms that transfer cam motion to the valves. Read more

One part is listed for the 1960 Edsel Villager — QUALCAST 402859.

This table covers the Rocker Arm shafts. Read more

3 Rocker Arm Shaft parts are listed for the 1960 Edsel Villager, from MELLING and QUALCAST.

Listed part numbers: MELLING MRS621, MELLING MRS641 and QUALCAST 422641.

This table covers the Timing Cam sprockets. Read more

One part is listed for the 1960 Edsel Villager — MELLING S284.

This table covers the timing chains that keep the cams in time with the crank. Read more

2 Timing Chain parts for the 1960 Edsel Villager come from MELLING.

This group includes MELLING 344 and MELLING 494.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

One part is listed for the 1960 Edsel Villager — MELLING 3344S.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Timing Cover Gasket parts are listed for the 1960 Edsel Villager, from MAHLE / CLEVITE, VICTOR REINZ and FEL-PRO.

Listed part numbers: FEL-PRO TCS106773, MAHLE / CLEVITE JV799 and MAHLE / CLEVITE JV819, plus the other parts above.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts are listed for the 1960 Edsel Villager, from MAHLE / CLEVITE and SKF.

This group includes MAHLE / CLEVITE 46293 and SKF 18546.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Valve Cover Gasket parts are listed for the 1960 Edsel Villager, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. FEL-PRO VS13049R carries the "Popular" badge.

Listed part numbers: FEL-PRO VS13049R, FEL-PRO VS12949 and FEL-PRO VS13049C, plus the other parts above.

This table covers the Valve Cover grommets. Read more

3 Valve Cover Grommet parts are listed for the 1960 Edsel Villager, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: FEL-PRO 10740, MAHLE / CLEVITE GS33732 and VICTOR REINZ 151016601.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

QUALCAST supplies the 8 Valve Guide parts for the 1960 Edsel Villager. QUALCAST 309108 carries the "Popular" badge.

This group includes QUALCAST 309108, QUALCAST 309606 and QUALCAST 309105 and the remaining parts above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

3 Valve Lifter parts are listed for the 1960 Edsel Villager, from MELLING, QUALCAST and SEALED POWER.

Part numbers include MELLING JB2083, QUALCAST 362083 and SEALED POWER HT2083.

This table covers the Valve seats. Read more

8 Valve Seat parts for the 1960 Edsel Villager come from 3 brands — QUALCAST, SEALED POWER and DURA-BOND.

Part numbers include DURA-BOND 30503, QUALCAST 2015622 and QUALCAST 2017503, among others listed above.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

4 Valve Spring parts for the 1960 Edsel Villager come from 2 brands — MELLING and QUALCAST.

Listed part numbers: MELLING VS140, MELLING VS160 and QUALCAST 32611, plus the other parts above.

This table covers the Valve Spring retainers. Read more

This group shows a single part: QUALCAST 556304.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

4 Valve Spring Retainer Keeper parts for the 1960 Edsel Villager come from 2 brands — MELLING and QUALCAST.

This group includes MELLING VL200, MELLING VL300 and QUALCAST 34555 and the remaining parts above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

12 Valve Stem Seal parts are listed for the 1960 Edsel Villager, from QUALCAST, VICTOR REINZ, MAHLE / CLEVITE and 1 other brand. FEL-PRO SS13401 carries the "Popular" badge.