1986 Excalibur Phaeton Ignition Parts

Engine:

Showing parts for every engine. Select an engine to see only what fits.

2 Ignition parts are listed for the 1986 Excalibur Phaeton, in 1 part type, covering both the 5.0L 305cid V8 and the 5.7L 350cid V8. Each one has a brand, a manufacturer part number and notes that say where it fits.

On the 1986 Excalibur Phaeton, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules. Every listed part is a Distributor Mounting Gasket.

Distributor Mounting Gasket

Brand Part Number Markets Notes Buy
FEL-PRO Fits: 5.0L 305cid V8 70194
🇺🇸 US
Thickness: 0.053 In
View on
Amazon
VICTOR REINZ Fits: 5.0L 305cid V8 711350200
🇺🇸 US
Inside Diameter: 1.280 In
View on
Amazon

This table covers the gaskets that seal the Distributor Mounting. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Buying Ignition Parts for a 1986 Excalibur Phaeton

On this vehicle, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules.

  • Match the engine first. Every ignition part here is engine-specific; each row shows which engine(s) it fits.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Distributor Mounting Gasket .

Frequently Asked Questions

How many ignition parts fit the 1986 Excalibur Phaeton?

Our catalog currently lists 2 ignition parts for the 1986 Excalibur Phaeton across 1 subcategory and 2 brands, covering both the 5.0L 305cid V8 and the 5.7L 350cid V8. Each part is matched to the engine(s) it fits.

Do ignition parts differ between 1986 Excalibur Phaeton engines?

Yes. Every ignition part on this page is engine-specific. Each row shows which engine(s) it fits — use the filter at the top to hide the rest. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.

What are the signs of ignition problems on a 1986 Excalibur Phaeton?

Common symptoms include misfires under load, rough idle, flashing check-engine light, or poor starting in damp weather. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What should I replace at the same time?

Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1986 Excalibur Phaeton was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 1986 Excalibur Phaeton?

First match the engine — each row shows which engine(s) the part fits. Then gap matters even on “pre-gapped” plugs — verify against spec, and replace coil boots when they come off a high-mileage engine. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 1986 Excalibur Phaeton

Ignition Parts for Other Excalibur Phaeton Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.