This page lists 4 belt drive parts for the 1952 Fargo F3B Pickup, across 1 part type, covering the 3.6L 218cid L6 engine. Every part shows its brand, manufacturer part number and fitment notes.
The belt drive system on the 1952 Fargo F3B Pickup spins the accessories — serpentine and V-belts, tensioners, idlers and pulleys. Every listed part is a Belt.
Every part on this page is matched to the 3.6L 218cid L6 — the only engine offered in the 1952 Fargo F3B Pickup.
The most listed brands for 1952 Fargo F3B Pickup belt drive parts are GATES (3 parts) and ACDELCO (1 part).
Each part number listed for the 1952 Fargo F3B Pickup opens a page with every vehicle that part fits.
Belt
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ACDELCO | 15480 | 🇺🇸 US 🇨🇦 CA | Professional / Gold | View on Amazon |
| GATES | TR24476 | 🇨🇦 CA | Green Stripe Truck & Bus V-BeltTA 21/32 x 48 1/4 | View on Amazon |
| GATES | 7480 | 🇨🇦 CA | XL High Capacity V-Belt | View on Amazon |
| GATES | TR24489 | 🇨🇦 CA | Green Stripe Truck & Bus V-BeltTA 21/32 x 49 3/8 | View on Amazon |
This table covers the serpentine and accessory belts that drive the front accessories. Typical signs include squeal on cold start, cracks across the ribs, or glazing on the back of the belt. A new belt on a worn tensioner will squeal within weeks — spin the idlers by hand while the belt is off.
4 Belt parts are listed for the 1952 Fargo F3B Pickup, from GATES and ACDELCO.
Listed part numbers: ACDELCO 15480, GATES TR24476 and GATES 7480, plus the other parts above.
Buying Belt Drive Parts for a 1952 Fargo F3B Pickup
On this vehicle, the belt drive system spins the accessories — serpentine and V-belts, tensioners, idlers and pulleys.
- Confirm you have the 3.6L 218cid L6 engine — every part on this page is matched to it.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace the tensioner and idler pulleys with any belt at higher mileage — the labor overlaps almost entirely.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Belt .
Frequently Asked Questions
How many belt drive parts fit the 1952 Fargo F3B Pickup?
Our catalog currently lists 4 belt drive parts for the 1952 Fargo F3B Pickup across 1 subcategory and 2 brands, covering the 3.6L 218cid L6 engine. Each part is matched to the engine(s) it fits.
What are the signs of belt drive problems on a 1952 Fargo F3B Pickup?
Common symptoms include squealing on cold start, a belt that shows cracking or glazing, or an accessory that slows under load. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace the tensioner and idler pulleys with any belt at higher mileage — the labor overlaps almost entirely.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1952 Fargo F3B Pickup was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 1952 Fargo F3B Pickup?
Every part on this page is matched to the 3.6L 218cid L6 engine. Then a new belt on a worn tensioner will squeal within weeks — check tensioner damping and idler bearings while the belt is off. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 1952 Fargo F3B Pickup
Belt Drive Parts for Other Fargo F3B Pickup Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.