1962 Fargo FW100 Pickup Engine Parts

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: SEALED POWER 1454M.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

7 Connecting Rod Bearing parts for the 1962 Fargo FW100 Pickup come from 2 brands — KING ENGINE BEARINGS and SEALED POWER. The "Popular" part is KING ENGINE BEARINGS CR805SI.

The High Performance section lists 4 options from KING ENGINE BEARINGS — engineered beyond original-equipment specification. KING ENGINE BEARINGS CR805XPN is listed in this group.

In the Standard Replacement grade, KING ENGINE BEARINGS supplies 1 part: built to original-equipment specification. A representative part number is KING ENGINE BEARINGS CR805SI.

2 further parts sit outside the graded sections, with the same engine-level match.

Part numbers include KING ENGINE BEARINGS CR805SI, KING ENGINE BEARINGS CR805XPN and KING ENGINE BEARINGS CR805XPNC, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Crankshaft Main Bearing parts are listed for the 1962 Fargo FW100 Pickup, from MAHLE / CLEVITE and KING ENGINE BEARINGS. MAHLE / CLEVITE MS540H carries the "Popular" badge.

High Performance: 4 parts, from MAHLE / CLEVITE and KING ENGINE BEARINGS. A representative part number is MAHLE / CLEVITE MS540H.

The Standard Replacement section: 2 options from MAHLE / CLEVITE and KING ENGINE BEARINGS. MAHLE / CLEVITE MS540P is listed in this group.

Part numbers include MAHLE / CLEVITE MS540H, KING ENGINE BEARINGS MB558XPC and KING ENGINE BEARINGS MB558XPCX, among others listed above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

One part is listed for the 1962 Fargo FW100 Pickup — WJB / INMOTION PARTS WS99226.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Crankshaft Seal parts are listed for the 1962 Fargo FW100 Pickup, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: FEL-PRO BS40240, FEL-PRO BS40245 and MAHLE / CLEVITE JV607, plus the other parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Cylinder Head Gasket parts for the 1962 Fargo FW100 Pickup come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: FEL-PRO 7918PT1, FEL-PRO 7734PT and MAHLE / CLEVITE 1162VC, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts for the 1962 Fargo FW100 Pickup come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: FEL-PRO HS7918PT4, FEL-PRO HS7734PT and MAHLE / CLEVITE HS1162VE, plus the other parts above.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Engine Kit Gasket Set parts for the 1962 Fargo FW100 Pickup come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. The "Popular" part is FEL-PRO 2601004.

Listed part numbers: FEL-PRO 2601004, FEL-PRO FS7918PT4 and FEL-PRO FS7734PT2, plus the other parts above.

This table covers the wear sleeves used to restore a Harmonic Balancer seal surface. Read more

One part is listed for the 1962 Fargo FW100 Pickup — MAHLE / CLEVITE 66593RS.

This table covers the Intake & Exhaust Manifold gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Intake & Exhaust Manifold Gasket Set parts for the 1962 Fargo FW100 Pickup come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO MS9610B1, MAHLE / CLEVITE MS16030 and VICTOR REINZ 711472900.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Intake Manifold Gasket parts for the 1962 Fargo FW100 Pickup come from 2 brands — FEL-PRO and VICTOR REINZ.

Part numbers include FEL-PRO MS9344SH and VICTOR REINZ 111042301.

This table covers the gaskets that seal the Intake to Exhaust. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Intake to Exhaust Gasket parts are listed for the 1962 Fargo FW100 Pickup, from FEL-PRO and VICTOR REINZ.

Listed part numbers: FEL-PRO 901042 and VICTOR REINZ 711382200.

This table covers the O-rings that seal this joint. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

One part is listed for the 1962 Fargo FW100 Pickup — VICTOR REINZ 411041400.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Drain Plug Gasket parts for the 1962 Fargo FW100 Pickup come from 2 brands — FEL-PRO and VICTOR REINZ.

Listed part numbers: FEL-PRO 70822 and VICTOR REINZ 711346200.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

FRAM supplies both parts for the 1962 Fargo FW100 Pickup.

In the High Performance / Heavy Duty grade, FRAM supplies 1 part: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is FRAM TG8A.

The Standard Replacement section: 1 option from FRAM. FRAM PH8A is listed in this group.

Listed part numbers: FRAM TG8A and FRAM PH8A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts are listed for the 1962 Fargo FW100 Pickup, from FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE.

This group includes FEL-PRO OS12705C1, FEL-PRO OS6566C1 and MAHLE / CLEVITE OS30920X and the remaining parts above.

This table covers the gaskets that seal the Oil Pressure Relief Valve. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Pressure Relief Valve Gasket parts for the 1962 Fargo FW100 Pickup come from 2 brands — FEL-PRO and VICTOR REINZ. Every part fits both the 3.7L 225cid L6 and the 5.1L 313cid V8.

This group includes FEL-PRO 3122 and VICTOR REINZ 711456300.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: VICTOR REINZ 711450000.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

This group shows a single part: SEALED POWER 244NP.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 1962 Fargo FW100 Pickup — SEALED POWER 2134Y.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts for the 1962 Fargo FW100 Pickup come from 2 brands — HASTINGS MANUFACTURING and SEALED POWER. The "Popular" part is HASTINGS MANUFACTURING 687.

In the Premium grade, HASTINGS MANUFACTURING supplies 1 part: a step above OE specification in materials, tolerances or warranty terms. A representative part number is HASTINGS MANUFACTURING 2M687.

Standard Replacement: 4 parts, from HASTINGS MANUFACTURING and SEALED POWER. A representative part number is HASTINGS MANUFACTURING 687.

This group includes HASTINGS MANUFACTURING 687, HASTINGS MANUFACTURING 2M687 and HASTINGS MANUFACTURING 2C687S and the remaining parts above.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Timing Cover Gasket parts are listed for the 1962 Fargo FW100 Pickup, from FEL-PRO, VICTOR REINZ and MAHLE / CLEVITE.

Listed part numbers: FEL-PRO TCS127691, FEL-PRO TCS65631 and MAHLE / CLEVITE JV814, plus the other parts above.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 1962 Fargo FW100 Pickup — MAHLE / CLEVITE 64572.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Valve Cover Gasket parts are listed for the 1962 Fargo FW100 Pickup, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

Listed part numbers: FEL-PRO VS12680, FEL-PRO VS11828C and MAHLE / CLEVITE VS39745, plus the other parts above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

One part is listed for the 1962 Fargo FW100 Pickup — SEALED POWER AT2084.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Valve Stem Seal parts are listed for the 1962 Fargo FW100 Pickup, from VICTOR REINZ, FEL-PRO and MAHLE / CLEVITE. 1 part fits every engine; the other 3 are engine-specific.

This group includes FEL-PRO SS12764, MAHLE / CLEVITE SS45298 and VICTOR REINZ 121007101 and the remaining parts above.