1989 Geo Metro Engine Parts

This table covers the Balance Shaft belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

2 Balance Shaft Belt parts for the 1989 Geo Metro come from 2 brands — CLOYES and FVP.

Part numbers include CLOYES B186, among others listed above.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

5 Camshaft Repair Sleeve parts are listed for the 1989 Geo Metro, from NATIONAL, SCHAEFFLER, SKF and 2 other brands. NATIONAL 99128 carries the "Popular" badge.

This group includes NATIONAL 99128, SCHAEFFLER SR3467 and SKF 99876 and the remaining parts above.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

10 Camshaft Seal parts are listed for the 1989 Geo Metro, from SCHAEFFLER, FEL-PRO, NATIONAL and 6 other brands. FEL-PRO TCS45852 carries the "Popular" badge.

This table covers the connecting rods between each piston and the crankshaft. Read more

This group shows a single part: TOPLINE CRSZ2M.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Connecting Rod Bearing parts for the 1989 Geo Metro come from 5 brands — MAHLE / CLEVITE, ENGINETECH, ITM ENGINE COMPONENTS and 2 other brands. The "Popular" part is ENGINETECH BB2403.

Listed part numbers: ENGINETECH BB2403, MAHLE / CLEVITE CB1401A and ITM ENGINE COMPONENTS 3B0001, plus the other parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts for the 1989 Geo Metro come from 4 brands — AJUSA, APEX, ENGINETECH and 1 other brand.

This group includes AJUSA 54056500, APEX ACS7004 and ENGINETECH SZ10CS and the remaining parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

7 Crankshaft Main Bearing parts are listed for the 1989 Geo Metro, from TOPLINE, ENGINETECH, MAHLE / CLEVITE and 3 other brands. ENGINETECH BC2403 carries the "Popular" badge.

Listed part numbers: ENGINETECH BC2403, MAHLE / CLEVITE MS1708A and ITM ENGINE COMPONENTS 4M9340, plus the other parts above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

2 Crankshaft Repair Sleeve parts are listed for the 1989 Geo Metro, from NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: NATIONAL 99128 and WJB / INMOTION PARTS WS99128.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

18 Crankshaft Seal parts are listed for the 1989 Geo Metro, from FEL-PRO, NATIONAL, WJB / INMOTION PARTS and 8 other brands. FEL-PRO TCS45461 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

6 Cylinder Head Bolt parts for the 1989 Geo Metro come from 6 brands — ENGINETECH, SKP, APEX and 3 other brands. The "Popular" part is ENGINETECH HB145.

Listed part numbers: ENGINETECH HB145, SKP SKES74021 and APEX AHB704, plus the other parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Cylinder Head Gasket parts for the 1989 Geo Metro come from 5 brands — FEL-PRO, APEX, ITM ENGINE COMPONENTS and 2 other brands. The "Popular" part is FEL-PRO 9651PT.

This group includes FEL-PRO 9651PT, APEX AHG704 and ITM ENGINE COMPONENTS 0940110 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts for the 1989 Geo Metro come from 5 brands — ENGINETECH, AJUSA, APEX and 2 other brands. The "Popular" part is ENGINETECH SZ10HS.

Listed part numbers: ENGINETECH SZ10HS, ENGINETECH SZ10HSWB and AJUSA 52098700, plus the other parts above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 1989 Geo Metro — DORMAN 090019.

This table covers the Cylinder Head Spacer shims. Read more

This group shows a single part: SBI 2302030.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

2 Cylinder Repair Sleeve parts for the 1989 Geo Metro come from MELLING.

Listed part numbers: MELLING CSL605A and MELLING CSL705A.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

One part is listed for the 1989 Geo Metro — KAT'S HEATERS 16400.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Engine Kit Gasket Set parts for the 1989 Geo Metro come from 5 brands — ENGINETECH, AJUSA, APEX and 2 other brands. The "Popular" part is ENGINETECH SZ10K1.

Part numbers include ENGINETECH SZ10K1, AJUSA 50111700 and APEX AFS7004, among others listed above.

This table covers the Engine rebuild kits. Read more

This group shows a single part: ENGINETECH RCGM10P.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts are listed for the 1989 Geo Metro, from ENGINETECH, ITM ENGINE COMPONENTS, QUALCAST and 2 other brands. ENGINETECH V2823 carries the "Popular" badge.

Part numbers include ENGINETECH V2823, ITM ENGINE COMPONENTS RX9432 and QUALCAST 1010170, among others listed above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts for the 1989 Geo Metro come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO MS94370.

Listed part numbers: FEL-PRO MS94370, AJUSA 13080900 and APEX AMS7040, plus the other parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

6 Intake Valve parts are listed for the 1989 Geo Metro, from ENGINETECH, SBI, ITM ENGINE COMPONENTS and 3 other brands. ENGINETECH V2818 carries the "Popular" badge.

Part numbers include ENGINETECH V2818, SBI 10169 and ITM ENGINE COMPONENTS RV9446, among others listed above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

10 Motor Mount parts are listed for the 1989 Geo Metro, from WESTAR, DEA / MARMON RIDE CONTROL, ANCHOR and 1 other brand. DEA / MARMON RIDE CONTROL A6814 carries the "Popular" badge.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

21 Oil parts are listed for the 1989 Geo Metro, from MOBIL, VALVOLINE and IDEMITSU. MOBIL 125195 carries the "Popular" badge.

In the Full Synthetic grade, MOBIL and VALVOLINE supply 8 parts: full-synthetic oils. A representative part number is MOBIL 125195.

The High Mileage (>75,000 Miles) section lists 8 options from VALVOLINE and MOBIL — oils grouped for high-mileage engines. VALVOLINE VV1556 is listed in this group.

In the Racing grade, IDEMITSU supplies 1 part: grouped under the catalog's "Racing" designation — the notes column spells out what sets them apart. A representative part number is IDEMITSU 30018100750.

In the Synthetic Blend grade, MOBIL and VALVOLINE supply 4 parts: synthetic-blend oils. A representative part number is MOBIL 124406.

This table covers the drain plugs in the oil pan. Read more

8 Oil Drain Plug parts are listed for the 1989 Geo Metro, from DORMAN, AGS and SKP. AGS ODP00007 carries the "Popular" badge.

The Piggyback section lists 1 option from DORMAN — grouped under the catalog's "Piggyback" designation — the notes column spells out what sets them apart. DORMAN 65229 is listed in this group.

The Twist Drain section lists 1 option from DORMAN — grouped under the catalog's "Twist Drain" designation — the notes column spells out what sets them apart. DORMAN 092020 is listed in this group.

The Universal section lists 1 option from DORMAN — grouped under the catalog's "Universal" designation — the notes column spells out what sets them apart. DORMAN 65102 is listed in this group.

5 ungrouped parts are not assigned to a grade, with the same engine-level match.

Part numbers include AGS ODP00007, DORMAN 65229 and DORMAN 092020, among others listed above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts for the 1989 Geo Metro come from 3 brands — DORMAN, JAPANESE OE and ULTRA-POWER.

Part numbers include DORMAN 095147, DORMAN 995147CD and JAPANESE OE KW32004, among others listed above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts are listed for the 1989 Geo Metro, from BECK/ARNLEY, GATES, MOTORAD and 1 other brand.

Listed part numbers: BECK/ARNLEY 0160125, GATES 31109 and MOTORAD MO81, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts are listed for the 1989 Geo Metro, from BOSCH, VARIOUS MFR, WIX and 10 other brands. WIX 51348XP carries the "Popular" badge.

In the Economy grade, BOSCH, FRAM, FVP and 2 other brands supply 5 parts: the catalog's value-priced group. A representative part number is BOSCH 72161WS.

In the High Performance / Heavy Duty grade, WIX and MOBIL supply 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 51348XP.

The Standard Replacement section lists 10 options from MOTORCRAFT, DENSO, WIX and 6 other brands — built to original-equipment specification. DENSO 1502010 is listed in this group.

This table covers the Oil Galley plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

GM GENUINE supplies both parts for the 1989 Geo Metro.

Part numbers include GM GENUINE 94033681 and GM GENUINE 10040001.

This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

One part is listed for the 1989 Geo Metro — WELLS 1S6556.

This table covers the oil pans that hold the engine's oil sump. Read more

3 Oil Pan parts for the 1989 Geo Metro come from 3 brands — ATP, PIONEER and SPECTRA PREMIUM.

Listed part numbers: ATP 103271, PIONEER 501101 and SPECTRA PREMIUM GMP14A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts are listed for the 1989 Geo Metro, from VICTOR REINZ, AJUSA, APEX and 1 other brand. VICTOR REINZ 703141410 carries the "Popular" badge.

Part numbers include VICTOR REINZ 703141410, AJUSA 14079000 and APEX AOP704, among others listed above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

6 Oil Pump parts are listed for the 1989 Geo Metro, from ITM ENGINE COMPONENTS, SKP, MELLING and 1 other brand. SKP SKOM238 carries the "Popular" badge.

Economy: 1 part, from SKP. A representative part number is SKP SKOM238.

The Standard Replacement section: 5 options from ITM ENGINE COMPONENTS, MELLING and ENGINETECH. MELLING M158 is listed in this group.

Part numbers include SKP SKOM238, MELLING M158 and ENGINETECH EP158, among others listed above.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: BECK/ARNLEY 0398004.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

5 Piston parts for the 1989 Geo Metro come from 4 brands — ENGINETECH, ITM ENGINE COMPONENTS, SILV-O-LITE and 1 other brand. The "Popular" part is ITM ENGINE COMPONENTS RY6440.

Part numbers include ITM ENGINE COMPONENTS RY6440, ENGINETECH P4665 and ENGINETECH K46653P, among others listed above.

This table covers the rings that seal each piston to the cylinder wall. Read more

7 Piston Ring parts for the 1989 Geo Metro come from 5 brands — HASTINGS MANUFACTURING, ENGINETECH, SEALED POWER and 2 other brands. The "Popular" part is ENGINETECH C74123.

In the Premium grade, ENGINETECH and SEALED POWER supply 2 parts: a step above OE specification in materials, tolerances or warranty terms. A representative part number is ENGINETECH C74123.

Standard Replacement: 5 parts, from HASTINGS MANUFACTURING, BECK/ARNLEY and ITM ENGINE COMPONENTS. A representative part number is HASTINGS MANUFACTURING 2C4208.

Listed part numbers: ENGINETECH C74123, SEALED POWER E549KC and HASTINGS MANUFACTURING 2C4208, plus the other parts above.

This table covers the Re-Ring kits. Read more

One part is listed for the 1989 Geo Metro — ENGINETECH RMGM10P.

This table covers the Thrust washers. Read more

4 Thrust Washer parts are listed for the 1989 Geo Metro, from ENGINETECH, ITM ENGINE COMPONENTS, KING ENGINE BEARINGS and 1 other brand.

This group includes ENGINETECH TW2403, ITM ENGINE COMPONENTS 1T1022 and KING ENGINE BEARINGS TW134AM and the remaining parts above.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

11 Timing Belt parts for the 1989 Geo Metro come from 11 brands — ENGINETECH, CLOYES, ITM ENGINE COMPONENTS and 8 other brands. The "Popular" part is ENGINETECH TB166.

The Economy section: 3 options from ENGINETECH, CLOYES and ITM ENGINE COMPONENTS. ENGINETECH TB166 is listed in this group.

Standard Replacement: 8 parts, from DAYCO, GATES, ACDELCO and 5 other brands. A representative part number is DAYCO 95166.

This table covers the Timing Belt & component kits. Read more

5 Timing Belt & Component Kit parts are listed for the 1989 Geo Metro, from CONTINENTAL, GATES, GMB and 2 other brands.

Listed part numbers: CONTINENTAL TB166K1, GATES TCK166 and GMB 24300166, plus the other parts above.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

2 Timing Belt Pulley parts are listed for the 1989 Geo Metro, from CLOYES and FVP.

Listed part numbers: CLOYES 95343, plus the other parts above.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

6 Timing Belt Tensioner parts are listed for the 1989 Geo Metro, from GMB, S.A. GEAR, DAYCO and 3 other brands. GMB 4308310 carries the "Popular" badge.

Part numbers include GMB 4308310, S.A. GEAR 9343 and DAYCO 84060, among others listed above.

This table covers the Timing Cover Dust Seal sets. Read more

2 Timing Cover Dust Seal Set parts are listed for the 1989 Geo Metro, from APEX and VICTOR REINZ.

This group includes APEX AES701 and VICTOR REINZ 711675600.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Timing Cover Gasket parts are listed for the 1989 Geo Metro, from MAHLE / CLEVITE and ULTRA-POWER.

This group includes MAHLE / CLEVITE JV5009 and MAHLE / CLEVITE B33030 and the remaining parts above.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

One part is listed for the 1989 Geo Metro — SKF 99128.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 1989 Geo Metro — SKF 12724.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

3 Timing Crank Sprocket parts are listed for the 1989 Geo Metro, from FVP, INA and S.A. GEAR.

Listed part numbers: FVP S643 and INA ZSS643, plus the other parts above.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

5 Torque Strut Mount parts for the 1989 Geo Metro come from 5 brands — FAMOUS BRAND, ANCHOR, DEA / MARMON RIDE CONTROL and 2 other brands. The "Popular" part is ANCHOR 8658.

The Economy section: 1 option from FAMOUS BRAND. FAMOUS BRAND 2010312065 is listed in this group.

Standard Replacement: 4 parts, from ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand. A representative part number is ANCHOR 8658.

This group includes ANCHOR 8658, FAMOUS BRAND 2010312065 and DEA / MARMON RIDE CONTROL A6818 and the remaining parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts are listed for the 1989 Geo Metro, from FEL-PRO, APEX, BECK/ARNLEY and 2 other brands. FEL-PRO VS50333R carries the "Popular" badge.

Listed part numbers: FEL-PRO VS50333R, APEX AVC704 and BECK/ARNLEY 0361428, plus the other parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

5 Valve Guide parts are listed for the 1989 Geo Metro, from ITM ENGINE COMPONENTS, SBI, QUALCAST and 1 other brand. SBI 1408324 carries the "Popular" badge.

This group includes SBI 1408324, ITM ENGINE COMPONENTS VG1056CI and ITM ENGINE COMPONENTS VG1056BR and the remaining parts above.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

6 Valve Lifter parts are listed for the 1989 Geo Metro, from MELLING, SEALED POWER, ITM ENGINE COMPONENTS and 3 other brands. MELLING JB6050 carries the "Popular" badge.

Part numbers include MELLING JB6050, SEALED POWER HT2272 and ITM ENGINE COMPONENTS 0565173, among others listed above.

This table covers the Valve seats. Read more

5 Valve Seat parts for the 1989 Geo Metro come from 3 brands — QUALCAST, SBI and ENGINETECH. The "Popular" part is ENGINETECH ST150077.

Listed part numbers: ENGINETECH ST150077, QUALCAST 21150077 and QUALCAST 21118752, plus the other parts above.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

3 Valve Spring Retainer Keeper parts for the 1989 Geo Metro come from 3 brands — MELLING, QUALCAST and SBI.

This group includes MELLING VL1060, QUALCAST 345008 and SBI 1211060.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Valve Stem Seal parts are listed for the 1989 Geo Metro, from SBI, APEX, ITM ENGINE COMPONENTS and 2 other brands. SBI 1221155 carries the "Popular" badge.

Part numbers include SBI 1221155, APEX AVS7004 and ITM ENGINE COMPONENTS SS273, among others listed above.