1933 Graham Model 65 Ignition Parts

Engine:
224cid L6

9 Ignition parts are listed for the 1933 Graham Model 65, in 4 part types, covering the 224cid L6 engine. Each one has a brand, a manufacturer part number and notes that say where it fits.

The ignition system on the 1933 Graham Model 65 delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules. The largest groups are Ignition Coil (6 parts), Distributor Rotor (1 part) and Ignition Breaker Points (1 part). The other 1 part type covers the remaining 1 part.

Distributor Rotor

Brand Part Number Markets Notes Buy
STANDARD MOTOR PRODUCTS DR157
🇺🇸 US
View on
Amazon

This table covers the Distributor rotors. Typical signs include shudder under braking, or a lip at the outer edge. Do not put new pads on a rotor that is below minimum thickness.

Ignition Breaker Points

Brand Part Number Markets Notes Buy
STANDARD MOTOR PRODUCTS DR1819
🇺🇸 US
View on
Amazon

This table covers the breaker points in a points-type distributor.

Ignition Coil

Economy

Brand Part Number Markets Notes Buy
STANDARD MOTOR PRODUCTS Popular UC14T
🇺🇸 US
T-Series6 Volt
View on
Amazon
FVP UC14F
🇺🇸 US
View on
Amazon
HOLSTEIN 2IGC0057
🇺🇸 US
View on
Amazon

Premium

Brand Part Number Markets Notes Buy
STANDARD MOTOR PRODUCTS Popular UC14
🇺🇸 US
Blue Streak6 Volt
View on
Amazon

Standard Replacement

Brand Part Number Markets Notes Buy
UNITED MOTOR PRODUCTS C14
🇺🇸 US
View on
Amazon
WELLS 5C1063
🇺🇸 US
Fits most cars, trucks, tractors & industrial engs6 Volt (Universal Coil) used with external resistor or where resistance wire is an internal part of wiring harness.
View on
Amazon

This table covers the coils that fire each spark plug. Typical signs include a misfire that follows one cylinder, a snap in damp weather, or a coil that is swollen or cracked. Swap a suspect coil with a neighbor to confirm, then replace boots that tore on the way off.

Spark Plug

Brand Part Number Markets Notes Buy
CHAMPION 561
🇺🇸 US
Copper PlusPre-Set Gap: 0.025"
Fitment notes — CHAMPION 561
Copper PlusPre-Set Gap: 0.025"
OE-Recommended Gap: 0.025"
View on
Amazon

This table covers the spark plugs for this engine. Typical signs include misfire under load, rough idle, or a flashing check-engine light. Verify the gap even on pre-gapped plugs, and replace coil boots that come off a high-mileage engine.

Buying Ignition Parts for a 1933 Graham Model 65

On this vehicle, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules.

  • Confirm you have the 224cid L6 engine — every part on this page is matched to it.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Ignition Coil and Distributor Rotor .

Frequently Asked Questions

How many ignition parts fit the 1933 Graham Model 65?

Our catalog currently lists 9 ignition parts for the 1933 Graham Model 65 across 4 subcategories and 6 brands, covering the 224cid L6 engine. Each part is matched to the engine(s) it fits.

What are the signs of ignition problems on a 1933 Graham Model 65?

Common symptoms include misfires under load, rough idle, flashing check-engine light, or poor starting in damp weather. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What spark-plug gap is listed for the 1933 Graham Model 65?

Notes on this page include a 0.025" pre-set gap. Still verify against spec — even “pre-gapped” plugs should be checked before they go in.

What should I replace at the same time?

Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1933 Graham Model 65 was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 1933 Graham Model 65?

Every part on this page is matched to the 224cid L6 engine. Then gap matters even on “pre-gapped” plugs — verify against spec, and replace coil boots when they come off a high-mileage engine. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 1933 Graham Model 65

Ignition Parts for Other Graham Model 65 Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.