1976 Honda Civic Engine Parts

This table covers the camshafts that open the valves. Read more

This group shows a single part: ITM ENGINE COMPONENTS 0562200.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

10 Camshaft Seal parts are listed for the 1976 Honda Civic, from MAHLE / CLEVITE, WJB / INMOTION PARTS, AUTO EXTRA and 7 other brands. MAHLE / CLEVITE 66580 carries the "Popular" badge.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: ITM ENGINE COMPONENTS 4B1950.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

This group shows a single part: AJUSA 54035300.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Crankshaft Main Bearing parts are listed for the 1976 Honda Civic, from KING ENGINE BEARINGS and ITM ENGINE COMPONENTS. KING ENGINE BEARINGS MB5168AM carries the "Popular" badge.

In the High Performance grade, KING ENGINE BEARINGS supplies 2 parts: engineered beyond original-equipment specification. A representative part number is KING ENGINE BEARINGS MB5168XP.

The Standard Replacement section lists 3 options from ITM ENGINE COMPONENTS and KING ENGINE BEARINGS — built to original-equipment specification. KING ENGINE BEARINGS MB5168AM is listed in this group.

Part numbers include KING ENGINE BEARINGS MB5168AM, KING ENGINE BEARINGS MB5168XP and KING ENGINE BEARINGS MB5168XPX, among others listed above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

5 Crankshaft Repair Sleeve parts are listed for the 1976 Honda Civic, from NATIONAL, BCA, SCHAEFFLER and 2 other brands. NATIONAL 99139 carries the "Popular" badge.

Listed part numbers: NATIONAL 99139, BCA NS99139 and SCHAEFFLER SR3472, plus the other parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Crankshaft Seal parts are listed for the 1976 Honda Civic, from ITM ENGINE COMPONENTS, TIMKEN, APEX and 3 other brands. ITM ENGINE COMPONENTS 1500902 carries the "Popular" badge.

Part numbers include ITM ENGINE COMPONENTS 1500902, TIMKEN 3771 and APEX ABS101, among others listed above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Cylinder Head Gasket parts for the 1976 Honda Civic come from 2 brands — AJUSA and ITM ENGINE COMPONENTS.

Listed part numbers: AJUSA 10025400 and ITM ENGINE COMPONENTS 0940901.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Cylinder Head Gasket Set parts for the 1976 Honda Civic come from 2 brands — AJUSA and ITM ENGINE COMPONENTS.

Part numbers include AJUSA 52062200 and ITM ENGINE COMPONENTS 0910901.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

2 Cylinder Repair Sleeve parts for the 1976 Honda Civic come from MELLING.

Part numbers include MELLING CSL704A and MELLING CSL604A.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts for the 1976 Honda Civic come from 2 brands — AJUSA and ITM ENGINE COMPONENTS.

This group includes AJUSA 50070100 and ITM ENGINE COMPONENTS 0900902.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

2 Exhaust Valve parts are listed for the 1976 Honda Civic, from ITM ENGINE COMPONENTS and MELLING.

Listed part numbers: ITM ENGINE COMPONENTS RX8806 and MELLING V5057.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Intake Manifold Gasket parts for the 1976 Honda Civic come from 2 brands — AJUSA and ITM ENGINE COMPONENTS.

Listed part numbers: AJUSA 13042000 and ITM ENGINE COMPONENTS 0950919.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

3 Intake Valve parts are listed for the 1976 Honda Civic, from BECK/ARNLEY, ITM ENGINE COMPONENTS and MELLING.

Part numbers include BECK/ARNLEY 0210617, ITM ENGINE COMPONENTS RV8805 and MELLING V5058.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

5 Motor Mount parts are listed for the 1976 Honda Civic, from DEA / MARMON RIDE CONTROL, ANCHOR, PIONEER and 1 other brand. DEA / MARMON RIDE CONTROL A4560 carries the "Popular" badge.

Listed part numbers: DEA / MARMON RIDE CONTROL A4560, ANCHOR 2449 and DEA / MARMON RIDE CONTROL A2449, plus the other parts above.

This table covers the Oil Cooler Mounting kits. Read more

2 Oil Cooler Mounting Kit parts for the 1976 Honda Civic come from HAYDEN.

Listed part numbers: HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

4 Oil Drain Plug parts are listed for the 1976 Honda Civic, from DORMAN and AGS.

This group includes AGS ODP00019, DORMAN 090040 and DORMAN 65221 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts for the 1976 Honda Civic come from 2 brands — DORMAN and AJUSA.

Part numbers include AJUSA 22009300, DORMAN 097831CD and DORMAN 095023, among others listed above.

This table covers the caps on the oil filler neck. Read more

One part is listed for the 1976 Honda Civic — MOTORAD MO106.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

5 Oil Filter parts are listed for the 1976 Honda Civic, from CHAMP / LUBER-FINER, WIX, FRAM and 1 other brand. WIX 51390 carries the "Popular" badge.

In the Economy grade, CHAMP / LUBER-FINER supplies 2 parts: the catalog's value-priced group. A representative part number is CHAMP / LUBER-FINER LF75HP.

The Standard Replacement section: 3 options from WIX, FRAM and HASTINGS / BALDWIN. WIX 51390 is listed in this group.

Part numbers include WIX 51390, CHAMP / LUBER-FINER LF75HP and CHAMP / LUBER-FINER PH2865, among others listed above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Pan Gasket parts are listed for the 1976 Honda Civic, from AJUSA, APEX and ITM ENGINE COMPONENTS.

This group includes AJUSA 14029600, APEX AOP101 and ITM ENGINE COMPONENTS 0990902.

This table covers the Oil Temperature senders. Read more

This group shows a single part: AUTO-TUNE PT3441.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

This group shows a single part: ITM ENGINE COMPONENTS RY2667.

This table covers the rings that seal each piston to the cylinder wall. Read more

7 Piston Ring parts for the 1976 Honda Civic come from 2 brands — HASTINGS MANUFACTURING and ITM ENGINE COMPONENTS. The "Popular" part is HASTINGS MANUFACTURING 4453.

Part numbers include HASTINGS MANUFACTURING 4453, ITM ENGINE COMPONENTS 0211566 and HASTINGS MANUFACTURING 2C6116, among others listed above.

This table covers the Thrust washers. Read more

3 Thrust Washer parts are listed for the 1976 Honda Civic, from ITM ENGINE COMPONENTS, KING ENGINE BEARINGS and MAHLE / CLEVITE.

This group includes ITM ENGINE COMPONENTS 1T1952, KING ENGINE BEARINGS TW110AM and MAHLE / CLEVITE TW327S.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

4 Timing Belt parts for the 1976 Honda Civic come from 4 brands — ITM ENGINE COMPONENTS, DAYCO, INA and 1 other brand.

The Economy section: 1 option from ITM ENGINE COMPONENTS. ITM ENGINE COMPONENTS 4028 is listed in this group.

Standard Replacement: 3 parts, from DAYCO, INA and S.A. GEAR. A representative part number is DAYCO 95028.

Part numbers include ITM ENGINE COMPONENTS 4028, DAYCO 95028 and INA ZBTB028, among others listed above.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

BECK/ARNLEY supplies both parts for the 1976 Honda Civic.

Part numbers include BECK/ARNLEY 0513860 and BECK/ARNLEY 0513954.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

4 Timing Belt Tensioner parts are listed for the 1976 Honda Civic, from CLOYES, FVP, INA and 1 other brand.

This group includes CLOYES 95019 and INA ZT95019 and the remaining parts above.

This table covers the Timing Cam sprockets. Read more

3 Timing Cam Sprocket parts are listed for the 1976 Honda Civic, from INA, ITM ENGINE COMPONENTS and S.A. GEAR.

This group includes INA ZSS520, ITM ENGINE COMPONENTS 50045 and S.A. GEAR S520.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

One part is listed for the 1976 Honda Civic — SKF 99138.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Timing Cover Seal parts are listed for the 1976 Honda Civic, from ITM ENGINE COMPONENTS, SCHAEFFLER and SKF.

Listed part numbers: ITM ENGINE COMPONENTS 1506101, SCHAEFFLER SS2442 and SKF 13907.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

3 Timing Crank Sprocket parts are listed for the 1976 Honda Civic, from INA, ITM ENGINE COMPONENTS and S.A. GEAR.

Listed part numbers: INA ZSS521, ITM ENGINE COMPONENTS 50044 and S.A. GEAR S521.

This table covers the Torque Strut bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

4 Torque Strut Bushing parts are listed for the 1976 Honda Civic, from DEA / MARMON RIDE CONTROL and PIONEER.

Listed part numbers: DEA / MARMON RIDE CONTROL A6539, DEA / MARMON RIDE CONTROL A6540 and PIONEER 628293, plus the other parts above.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

3 Torque Strut Mount parts for the 1976 Honda Civic come from 2 brands — ANCHOR and WESTAR.

Part numbers include ANCHOR 8029, ANCHOR 8293 and WESTAR EM8029.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Valve Cover Gasket parts are listed for the 1976 Honda Civic, from AJUSA and ITM ENGINE COMPONENTS.

Listed part numbers: AJUSA 56014900 and ITM ENGINE COMPONENTS 0930903.

This table covers the Valve Cover grommets. Read more

4 Valve Cover Grommet parts are listed for the 1976 Honda Civic, from APEX, FEL-PRO, JAPANESE OE and 1 other brand.

Listed part numbers: APEX AES100, FEL-PRO ES70337 and JAPANESE OE KF81126, plus the other parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

ITM ENGINE COMPONENTS supplies the 6 Valve Guide parts for the 1976 Honda Civic. ITM ENGINE COMPONENTS VG917CI carries the "Popular" badge.

This group includes ITM ENGINE COMPONENTS VG917CI, ITM ENGINE COMPONENTS VG875CI and ITM ENGINE COMPONENTS VG918CI and the remaining parts above.

This table covers the Valve seats. Read more

4 Valve Seat parts for the 1976 Honda Civic come from 4 brands — DURA-BOND, PIONEER, QUALCAST and 1 other brand.

Listed part numbers: DURA-BOND 31063, PIONEER 38530 and QUALCAST 21137552, plus the other parts above.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

This group shows a single part: ITM ENGINE COMPONENTS VS1137.

This table covers the Valve Spring retainers. Read more

This group shows a single part: ITM ENGINE COMPONENTS 051133.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

This group shows a single part: PIONEER PF234.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Valve Stem Seal parts are listed for the 1976 Honda Civic, from AJUSA and ITM ENGINE COMPONENTS.

Part numbers include AJUSA 12003900, AJUSA 12004000 and AJUSA 57028200, among others listed above.