1984 Honda Civic Engine Parts

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 1984 Honda Civic — DURA-BOND HA2.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

This group shows a single part: TIMKEN KWK99112.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

13 Camshaft Seal parts for the 1984 Honda Civic come from 11 brands — FEL-PRO, APEX, MAHLE / CLEVITE and 8 other brands. The "Popular" part is FEL-PRO TCS45620.

This table covers the connecting rods between each piston and the crankshaft. Read more

One part is listed for the 1984 Honda Civic — TOPLINE CRH14.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Connecting Rod Bearing parts are listed for the 1984 Honda Civic, from MAHLE / CLEVITE, ITM ENGINE COMPONENTS, KING ENGINE BEARINGS and 1 other brand. MAHLE / CLEVITE CB1459P carries the "Popular" badge.

Listed part numbers: MAHLE / CLEVITE CB1459P, ITM ENGINE COMPONENTS 4B1951 and KING ENGINE BEARINGS CR4139AM, plus the other parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts are listed for the 1984 Honda Civic, from VICTOR REINZ, APEX and TOPLINE.

Part numbers include APEX ACS1000, TOPLINE CBSH14 and VICTOR REINZ 081252501, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Crankshaft Main Bearing parts for the 1984 Honda Civic come from 3 brands — KING ENGINE BEARINGS, TOPLINE and ITM ENGINE COMPONENTS. The "Popular" part is KING ENGINE BEARINGS MB5168AM.

The High Performance section lists 1 option from KING ENGINE BEARINGS — engineered beyond original-equipment specification. KING ENGINE BEARINGS MB5168XP is listed in this group.

In the Standard Replacement grade, TOPLINE, KING ENGINE BEARINGS and ITM ENGINE COMPONENTS supply 4 parts: built to original-equipment specification. A representative part number is KING ENGINE BEARINGS MB5168AM.

Part numbers include KING ENGINE BEARINGS MB5168AM, KING ENGINE BEARINGS MB5168XP and ITM ENGINE COMPONENTS 5M9502, among others listed above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

7 Crankshaft Repair Sleeve parts for the 1984 Honda Civic come from 6 brands — SCHAEFFLER, BCA, FEL-PRO and 3 other brands. The "Popular" part is BCA NS99315.

Listed part numbers: BCA NS99315, FEL-PRO 16275 and SCHAEFFLER SR3466, plus the other parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

20 Crankshaft Seal parts for the 1984 Honda Civic come from 11 brands — APEX, SCHAEFFLER, FEL-PRO and 8 other brands. The "Popular" part is FEL-PRO BS40430.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Cylinder Head Gasket parts are listed for the 1984 Honda Civic, from APEX, FEL-PRO, ELRING and 4 other brands. APEX AHG100 carries the "Popular" badge.

Part numbers include APEX AHG100, FEL-PRO 9219PT1 and ELRING 526895, among others listed above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

8 Cylinder Head Gasket Set parts are listed for the 1984 Honda Civic, from FEL-PRO, VICTOR REINZ, APEX and 3 other brands. APEX AHS1000 carries the "Popular" badge.

This group includes APEX AHS1000, FEL-PRO HS9219PT1 and FEL-PRO HS9219PT3 and the remaining parts above.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

MELLING supplies both parts for the 1984 Honda Civic.

Part numbers include MELLING CSL605A and MELLING CSL705A.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts are listed for the 1984 Honda Civic, from APEX and TOPLINE.

This group includes APEX AFS1000 and TOPLINE CGSH14.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

4 Exhaust Valve parts for the 1984 Honda Civic come from 4 brands — ENGINETECH, ITM ENGINE COMPONENTS, QUALCAST and 1 other brand.

This group includes ENGINETECH EM2545, ITM ENGINE COMPONENTS RX9267 and QUALCAST 1010189 and the remaining parts above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

7 Expansion Plug parts are listed for the 1984 Honda Civic, from PIONEER, QUALCAST and DORMAN. DORMAN 116203 carries the "Popular" badge.

Listed part numbers: DORMAN 116203, PIONEER EPC224 and PIONEER PE153, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts are listed for the 1984 Honda Civic, from FEL-PRO, APEX and VICTOR REINZ. FEL-PRO MS92226 carries the "Popular" badge.

Part numbers include FEL-PRO MS92226, APEX AMS1000 and APEX AMS1100, among others listed above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Intake Valve parts for the 1984 Honda Civic come from 4 brands — BECK/ARNLEY, ENGINETECH, QUALCAST and 1 other brand. The "Popular" part is BECK/ARNLEY 0213267.

Listed part numbers: BECK/ARNLEY 0213267, BECK/ARNLEY 0213265 and ENGINETECH IM2500, plus the other parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

7 Motor Mount parts for the 1984 Honda Civic come from 4 brands — WESTAR, DEA / MARMON RIDE CONTROL, ANCHOR and 1 other brand. The "Popular" part is DEA / MARMON RIDE CONTROL A6501.

Part numbers include DEA / MARMON RIDE CONTROL A6501, WESTAR EM8402 and ANCHOR 8004, among others listed above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

67 Oil parts for the 1984 Honda Civic come from 4 brands — VALVOLINE, MOBIL, LIQUI MOLY and 1 other brand. The "Popular" part is MOBIL 125195. Conventional, Full Synthetic, High Mileage (>75,000 Miles), Racing and Synthetic Blend are all represented, and High Mileage (>75,000 Miles) alone accounts for 24 parts.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 1984 Honda Civic.

Part numbers include HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

11 Oil Drain Plug parts for the 1984 Honda Civic come from 5 brands — DORMAN, ELRING, AGS and 2 other brands. The "Popular" part is AGS ODP00007.

In the Piggyback grade, DORMAN supplies 1 part: grouped under the catalog's "Piggyback" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 65229.

In the Twist Drain grade, DORMAN supplies 1 part: grouped under the catalog's "Twist Drain" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 092020.

In the Universal grade, DORMAN supplies 1 part: grouped under the catalog's "Universal" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 65102.

8 further parts sit outside the graded sections, with the same engine-level match.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts are listed for the 1984 Honda Civic, from ULTRA-POWER, DORMAN and ELRING.

Part numbers include DORMAN 095144, ELRING 243600 and ULTRA-POWER 095015, among others listed above.

This table covers the caps on the oil filler neck. Read more

This group shows a single part: MOTORAD MO106.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts for the 1984 Honda Civic come from 12 brands — CHAMP / LUBER-FINER, VARIOUS MFR, FAMOUS BRAND and 9 other brands. The "Popular" part is VARIOUS MFR PG4651.

The Economy section lists 13 options from CHAMP / LUBER-FINER, FAMOUS BRAND, VARIOUS MFR and 7 other brands — the catalog's value-priced group. VARIOUS MFR PG4651 is listed in this group.

Standard Replacement: 4 parts, from FRAM, VARIOUS MFR, WIX and 1 other brand. A representative part number is FRAM PH3531.

This table covers the oil pans that hold the engine's oil sump. Read more

3 Oil Pan parts are listed for the 1984 Honda Civic, from ATP, PIONEER and SPECTRA PREMIUM.

Part numbers include ATP 103297, PIONEER 501126 and SPECTRA PREMIUM HOP02A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts for the 1984 Honda Civic come from 5 brands — FEL-PRO, APEX, ELRING and 2 other brands. The "Popular" part is FEL-PRO OS30542R.

This group includes FEL-PRO OS30542R, APEX AOP100 and ELRING 705110 and the remaining parts above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

3 Oil Pump parts for the 1984 Honda Civic come from 3 brands — ENGINETECH, MELLING and TOPLINE.

This group includes ENGINETECH EP149, MELLING M149 and TOPLINE OPH14.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

3 Piston parts are listed for the 1984 Honda Civic, from ENGINETECH, ITM ENGINE COMPONENTS and TOPLINE.

Listed part numbers: ENGINETECH P4111, ITM ENGINE COMPONENTS RY6618 and TOPLINE PAH14.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts are listed for the 1984 Honda Civic, from SEALED POWER, ENGINETECH, HASTINGS MANUFACTURING and 1 other brand. ENGINETECH C74114 carries the "Popular" badge.

The Premium section lists 2 options from ENGINETECH and SEALED POWER — a step above OE specification in materials, tolerances or warranty terms. ENGINETECH C74114 is listed in this group.

The Standard Replacement section: 3 options from HASTINGS MANUFACTURING, ITM ENGINE COMPONENTS and SEALED POWER. HASTINGS MANUFACTURING 2C6173 is listed in this group.

This group includes ENGINETECH C74114, SEALED POWER E438KC and HASTINGS MANUFACTURING 2C6173 and the remaining parts above.

This table covers the Re-Ring kits. Read more

This group shows a single part: ENGINETECH RMHO15P.

This table covers the rocker arms that transfer cam motion to the valves. Read more

2 Rocker Arm parts for the 1984 Honda Civic come from TOPLINE.

Listed part numbers: TOPLINE RAH14A and TOPLINE RAH14B.

This table covers the Thrust washers. Read more

2 Thrust Washer parts for the 1984 Honda Civic come from 2 brands — KING ENGINE BEARINGS and MAHLE / CLEVITE.

Part numbers include KING ENGINE BEARINGS TW110AM and MAHLE / CLEVITE TW327S.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

7 Timing Belt parts are listed for the 1984 Honda Civic, from CADNA, CLOYES, FVP and 4 other brands. CADNA TB099 carries the "Popular" badge.

Economy: 3 parts, from CADNA, CLOYES and FVP. A representative part number is CADNA TB099.

The Standard Replacement section: 4 options from BECK/ARNLEY, ACDELCO, S.A. GEAR and 1 other brand. BECK/ARNLEY 0260208 is listed in this group.

Listed part numbers: CADNA TB099 and CLOYES B099, plus the other parts above.

This table covers the Timing Belt & component kits. Read more

5 Timing Belt & Component Kit parts for the 1984 Honda Civic come from 4 brands — GMB, ITM ENGINE COMPONENTS, PREFERRED COMPONENTS INC and 1 other brand. The "Popular" part is ITM ENGINE COMPONENTS ITM161.

This group includes ITM ENGINE COMPONENTS ITM161, GMB 24350161 and GMB 34350161 and the remaining parts above.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

2 Timing Belt Pulley parts for the 1984 Honda Civic come from BECK/ARNLEY.

Listed part numbers: BECK/ARNLEY 0513860 and BECK/ARNLEY 0513954.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

6 Timing Belt Tensioner parts for the 1984 Honda Civic come from 6 brands — GMB, JAPANESE OE, CLOYES and 3 other brands. The "Popular" part is GMB 4358590.

Listed part numbers: GMB 4358590, JAPANESE OE DG30552RD1DCS28V1 and CLOYES 95126, plus the other parts above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: ITM ENGINE COMPONENTS 60204.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

2 Timing Cover Repair Sleeve parts for the 1984 Honda Civic come from 2 brands — SCHAEFFLER and SKF.

Part numbers include SCHAEFFLER SR3465 and SKF 99123.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts for the 1984 Honda Civic come from 2 brands — ITM ENGINE COMPONENTS and SKF.

This group includes ITM ENGINE COMPONENTS 1500908 and SKF 12301.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

7 Valve Guide parts for the 1984 Honda Civic come from 3 brands — ITM ENGINE COMPONENTS, QUALCAST and TOPLINE. The "Popular" part is QUALCAST 307830.

This group includes QUALCAST 307830, TOPLINE IVGH3 and ITM ENGINE COMPONENTS VG979CI and the remaining parts above.

This table covers the Valve seats. Read more

5 Valve Seat parts are listed for the 1984 Honda Civic, from PIONEER, QUALCAST and SBI.

Listed part numbers: PIONEER 38510, PIONEER 38520 and QUALCAST 21137555, plus the other parts above.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

SEALED POWER supplies both parts for the 1984 Honda Civic.

Part numbers include SEALED POWER VS838 and SEALED POWER VS1450.

This table covers the Valve Spring retainers. Read more

One part is listed for the 1984 Honda Civic — ITM ENGINE COMPONENTS 051142.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

One part is listed for the 1984 Honda Civic — PIONEER PF234.