1989 Honda CRX Engine Parts

This table covers the Barometric pressure sensors. Typical signs include a check-engine light for MAP or fuel-rail pressure, or a limp mode under load. A vacuum leak or a clogged reference line will fake a bad pressure sensor. Read more

One part is listed for the 1989 Honda CRX — WELLS 5S1170.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

2 Camshaft Repair Sleeve parts for the 1989 Honda CRX come from 2 brands — SCHAEFFLER and TIMKEN.

Listed part numbers: SCHAEFFLER SR3462 and TIMKEN KWK99112.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

15 Camshaft Seal parts for the 1989 Honda CRX come from 12 brands — FEL-PRO, APEX, ELRING and 9 other brands. The "Popular" part is FEL-PRO TCS45620.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

12 Connecting Rod Bearing parts are listed for the 1989 Honda CRX, from MAHLE / CLEVITE, KING ENGINE BEARINGS, ENGINETECH and 3 other brands. MAHLE / CLEVITE CB1461HN carries the "Popular" badge.

In the High Performance grade, KING ENGINE BEARINGS and MAHLE / CLEVITE supply 5 parts: engineered beyond original-equipment specification. A representative part number is MAHLE / CLEVITE CB1461HN.

The Standard Replacement section lists 7 options from MAHLE / CLEVITE, ENGINETECH, ITM ENGINE COMPONENTS and 3 other brands — built to original-equipment specification. MAHLE / CLEVITE CB1461P is listed in this group.

This table covers the Connecting Rod bolts. Read more

This group shows a single part: ARP 2086001.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Conversion / Lower Gasket Set parts are listed for the 1989 Honda CRX, from ENGINETECH, AJUSA, APEX and 2 other brands. ENGINETECH HO15CSA carries the "Popular" badge.

Listed part numbers: ENGINETECH HO15CSA, AJUSA 54060100 and APEX ACS1003, plus the other parts above.

This table covers the crankshafts that turn piston motion into rotation. Read more

One part is listed for the 1989 Honda CRX — ENGINETECH 852700.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

10 Crankshaft Main Bearing parts for the 1989 Honda CRX come from 6 brands — MAHLE / CLEVITE, KING ENGINE BEARINGS, TOPLINE and 3 other brands. The "Popular" part is KING ENGINE BEARINGS MB5568AM.

The High Performance section: 2 options from KING ENGINE BEARINGS and MAHLE / CLEVITE. KING ENGINE BEARINGS MB5568XP is listed in this group.

Standard Replacement: 8 parts, from MAHLE / CLEVITE, TOPLINE, KING ENGINE BEARINGS and 3 other brands. A representative part number is KING ENGINE BEARINGS MB5568AM.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

5 Crankshaft Repair Sleeve parts for the 1989 Honda CRX come from 5 brands — BCA, FEL-PRO, SCHAEFFLER and 2 other brands. The "Popular" part is BCA NS99315.

Part numbers include BCA NS99315, FEL-PRO 16275 and SCHAEFFLER SR3549, among others listed above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

22 Crankshaft Seal parts for the 1989 Honda CRX come from 13 brands — FEL-PRO, APEX, NATIONAL and 10 other brands. The "Popular" part is FEL-PRO BS40430.

This table covers the bolts that clamp the cylinder head to the block. Read more

2 Cylinder Head Bolt parts are listed for the 1989 Honda CRX, from ELRING and MAHLE / CLEVITE.

This group includes ELRING 706120 and MAHLE / CLEVITE GS33750.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

15 Cylinder Head Gasket parts are listed for the 1989 Honda CRX, from ELRING, APEX, FEL-PRO and 6 other brands. APEX AHG103S carries the "Popular" badge.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

12 Cylinder Head Gasket Set parts are listed for the 1989 Honda CRX, from VICTOR REINZ, FEL-PRO, APEX and 6 other brands. APEX AHS1003 carries the "Popular" badge.

This table covers the Cylinder Head Spacer shims. Read more

One part is listed for the 1989 Honda CRX — SBI 2302037.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

MELLING supplies both parts for the 1989 Honda CRX.

Listed part numbers: MELLING CSL616 and MELLING CSL716.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

This group shows a single part: KAT'S HEATERS 11419.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Engine Kit Gasket Set parts are listed for the 1989 Honda CRX, from APEX, ENGINETECH, AJUSA and 3 other brands. APEX AFS1003 carries the "Popular" badge.

Listed part numbers: APEX AFS1003, ENGINETECH HO15K1 and AJUSA 50115800, plus the other parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts for the 1989 Honda CRX come from 5 brands — ENGINETECH, ITM ENGINE COMPONENTS, QUALCAST and 2 other brands. The "Popular" part is ENGINETECH EM2491.

This group includes ENGINETECH EM2491, ITM ENGINE COMPONENTS RX35036HP and QUALCAST 1010191 and the remaining parts above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

QUALCAST supplies both parts for the 1989 Honda CRX.

This group includes QUALCAST 97110B and QUALCAST 97110.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Intake Manifold Gasket parts are listed for the 1989 Honda CRX, from APEX, FEL-PRO, AJUSA and 4 other brands. APEX AMS1030 carries the "Popular" badge.

Listed part numbers: APEX AMS1030, FEL-PRO MS941192 and AJUSA 13109500, plus the other parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Intake Valve parts for the 1989 Honda CRX come from 5 brands — ENGINETECH, ITM ENGINE COMPONENTS, QUALCAST and 2 other brands. The "Popular" part is ENGINETECH IM2452.

Part numbers include ENGINETECH IM2452, ITM ENGINE COMPONENTS RV35035HP and QUALCAST 1010190, among others listed above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

14 Motor Mount parts for the 1989 Honda CRX come from 6 brands — ANCHOR, WESTAR, DEA / MARMON RIDE CONTROL and 3 other brands. The "Popular" part is SKP SKM8411.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SKM8411 is listed in this group.

Standard Replacement: 13 parts, from ANCHOR, WESTAR, DEA / MARMON RIDE CONTROL and 2 other brands. A representative part number is ANCHOR 8006.

This table covers the Motor Mount kits. Read more

This group shows a single part: ANCHOR 301170.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

21 Oil parts for the 1989 Honda CRX come from 3 brands — MOBIL, VALVOLINE and IDEMITSU. The "Popular" part is MOBIL 125195.

The Full Synthetic section lists 8 options from MOBIL and VALVOLINE — full-synthetic oils. MOBIL 125195 is listed in this group.

In the High Mileage (>75,000 Miles) grade, VALVOLINE and MOBIL supply 8 parts: oils grouped for high-mileage engines. A representative part number is VALVOLINE VV1556.

The Racing section lists 1 option from IDEMITSU — grouped under the catalog's "Racing" designation — the notes column spells out what sets them apart. IDEMITSU 30018100750 is listed in this group.

The Synthetic Blend section lists 4 options from MOBIL and VALVOLINE — synthetic-blend oils. MOBIL 124406 is listed in this group.

This table covers the Oil Cooler Mounting kits. Read more

HAYDEN supplies both parts for the 1989 Honda CRX.

Part numbers include HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

11 Oil Drain Plug parts for the 1989 Honda CRX come from 5 brands — DORMAN, ELRING, AGS and 2 other brands. The "Popular" part is AGS ODP00007.

In the Piggyback grade, DORMAN supplies 1 part: grouped under the catalog's "Piggyback" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 65229.

In the Twist Drain grade, DORMAN supplies 1 part: grouped under the catalog's "Twist Drain" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 092020.

In the Universal grade, DORMAN supplies 1 part: grouped under the catalog's "Universal" designation — the notes column spells out what sets them apart. A representative part number is DORMAN 65102.

8 further parts sit outside the graded sections, with the same engine-level match.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts are listed for the 1989 Honda CRX, from ULTRA-POWER, DORMAN, AJUSA and 1 other brand. DORMAN 095144 carries the "Popular" badge.

Part numbers include DORMAN 095144, AJUSA 22007400 and ELRING 243600, among others listed above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts for the 1989 Honda CRX come from 4 brands — BECK/ARNLEY, GATES, MOTORAD and 1 other brand.

This group includes BECK/ARNLEY 0160125, GATES 31109 and MOTORAD MO81 and the remaining parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts for the 1989 Honda CRX come from 13 brands — VARIOUS MFR, BOSCH, WIX and 10 other brands. The "Popular" part is WIX 51334XP.

The Economy section: 6 options from VARIOUS MFR, BOSCH, FRAM and 2 other brands. BOSCH 72228WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 51334XP is listed in this group.

Standard Replacement: 9 parts, from BOSCH, DENSO, WIX and 6 other brands. A representative part number is BOSCH 3312.

This table covers the Oil Filter Support tubes. Read more

One part is listed for the 1989 Honda CRX — AUTOTECNICA HA1416938.

This table covers the oil pans that hold the engine's oil sump. Read more

5 Oil Pan parts are listed for the 1989 Honda CRX, from SKP, ATP, DORMAN and 2 other brands. SKP SK264402 carries the "Popular" badge.

This group includes SKP SK264402, ATP 103064 and DORMAN 264402 and the remaining parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Pan Gasket parts for the 1989 Honda CRX come from 6 brands — FEL-PRO, ITM ENGINE COMPONENTS, APEX and 3 other brands. The "Popular" part is FEL-PRO OS30542R.

This group includes FEL-PRO OS30542R, ITM ENGINE COMPONENTS 0990907 and APEX AOP100 and the remaining parts above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

5 Oil Pump parts for the 1989 Honda CRX come from 5 brands — SKP, MELLING, ENGINETECH and 2 other brands. The "Popular" part is MELLING M178.

The Economy section: 1 option from SKP. SKP SKOM178 is listed in this group.

Standard Replacement: 4 parts, from MELLING, ENGINETECH, ITM ENGINE COMPONENTS and 1 other brand. A representative part number is MELLING M178.

Listed part numbers: MELLING M178, SKP SKOM178 and ENGINETECH EP085, plus the other parts above.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 1989 Honda CRX — BECK/ARNLEY 0398014.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

2 Piston parts are listed for the 1989 Honda CRX, from ITM ENGINE COMPONENTS and TOPLINE.

This group includes ITM ENGINE COMPONENTS RY6234 and TOPLINE PAH22.

This table covers the rings that seal each piston to the cylinder wall. Read more

7 Piston Ring parts are listed for the 1989 Honda CRX, from HASTINGS MANUFACTURING, ENGINETECH, MAHLE / CLEVITE and 3 other brands. ENGINETECH C75154 carries the "Popular" badge.

The Premium section lists 3 options from ENGINETECH, MAHLE / CLEVITE and SEALED POWER — a step above OE specification in materials, tolerances or warranty terms. ENGINETECH C75154 is listed in this group.

The Standard Replacement section: 4 options from HASTINGS MANUFACTURING, ITM ENGINE COMPONENTS and TOPLINE. HASTINGS MANUFACTURING 2C4640 is listed in this group.

Listed part numbers: ENGINETECH C75154, MAHLE / CLEVITE 41592CP and SEALED POWER E515KC, plus the other parts above.

This table covers the Re-Ring kits. Read more

This group shows a single part: ENGINETECH RMHO16AP.

This table covers the rocker arms that transfer cam motion to the valves. Read more

4 Rocker Arm parts for the 1989 Honda CRX come from ITM ENGINE COMPONENTS.

Listed part numbers: ITM ENGINE COMPONENTS 0566223, ITM ENGINE COMPONENTS 0566222 and ITM ENGINE COMPONENTS 0566224, plus the other parts above.

This table covers the Thrust washers. Read more

6 Thrust Washer parts for the 1989 Honda CRX come from 6 brands — ENGINETECH, MAHLE / CLEVITE, ENGINE PRO and 3 other brands. The "Popular" part is ENGINETECH TW1516.

This group includes ENGINETECH TW1516, MAHLE / CLEVITE TW473S and ENGINE PRO 13473S and the remaining parts above.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

7 Timing Belt parts are listed for the 1989 Honda CRX, from GATES, ITM ENGINE COMPONENTS, SKP and 3 other brands. GATES T145RB carries the "Popular" badge.

Economy: 2 parts, from ITM ENGINE COMPONENTS and SKP. A representative part number is ITM ENGINE COMPONENTS 4130.

High Performance: 1 part, from GATES. A representative part number is GATES T145RB.

The Standard Replacement section: 4 options from GATES, CONTINENTAL, DAYCO and 1 other brand. GATES T145 is listed in this group.

This group includes GATES T145RB, ITM ENGINE COMPONENTS 4130 and SKP SKT145 and the remaining parts above.