2010 Honda Civic Engine Parts

This table covers the chains that drive the balance shafts. Read more

5 Balance Shaft Chain parts for the 2010 Honda Civic come from 3 brands — INA, S.A. GEAR and MELLING. The "Popular" part is MELLING 712F.

In the Chain Only grade, S.A. GEAR, MELLING and INA supply 4 parts: grouped under the catalog's "Chain Only" designation — the notes column spells out what sets them apart. A representative part number is MELLING 712F.

The Kit section lists 1 option from INA — grouped under the catalog's "Kit" designation — the notes column spells out what sets them apart. INA ZC76232 is listed in this group.

Part numbers include MELLING 712F, INA ZCC712F and S.A. GEAR C712F, among others listed above.

This table covers the guides that keep the balance-shaft chain on its path. Read more

5 Balance Shaft Chain Guide parts for the 2010 Honda Civic come from 5 brands — S.A. GEAR, BECK/ARNLEY, CLOYES and 2 other brands. The "Popular" part is S.A. GEAR 7518.

Listed part numbers: S.A. GEAR 7518, BECK/ARNLEY 0241929 and CLOYES 95570, plus the other parts above.

This table covers the Balance Shaft Chain tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

2 Balance Shaft Chain Tensioner parts are listed for the 2010 Honda Civic, from INA and S.A. GEAR.

Part numbers include INA ZT91038 and S.A. GEAR 91038.

This table covers the Balance Shaft sprockets. Read more

5 Balance Shaft Sprocket parts for the 2010 Honda Civic come from 5 brands — MELLING, CLOYES, FVP and 2 other brands. The "Popular" part is MELLING S939.

Part numbers include MELLING S939, among others listed above.

This table covers the Camshaft caps. Typical signs include a leak at the neck, a cap that will not hold pressure, or a missing tether. Match the pressure rating or thread in the notes — radiator, reservoir and fuel caps are not interchangeable. Read more

This group shows a single part: AJUSA 00794900.

This table covers the Camshaft plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

This group shows a single part: ELRING 459380.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Camshaft Seal parts are listed for the 2010 Honda Civic, from FEL-PRO, APEX, ELRING and 2 other brands. FEL-PRO TCS46212 carries the "Popular" badge.

Listed part numbers: FEL-PRO TCS46212, APEX ATC1540 and ELRING 290710, plus the other parts above.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

16 Connecting Rod Bearing parts for the 2010 Honda Civic come from 5 brands — MAHLE / CLEVITE, KING ENGINE BEARINGS, ENGINETECH and 2 other brands. The "Popular" part is MAHLE / CLEVITE CB1861H.

The High Performance section lists 4 options from MAHLE / CLEVITE and KING ENGINE BEARINGS — engineered beyond original-equipment specification. MAHLE / CLEVITE CB1861H is listed in this group.

In the Standard Replacement grade, ENGINETECH, ITM ENGINE COMPONENTS, KING ENGINE BEARINGS and 1 other brand supply 4 parts: built to original-equipment specification. A representative part number is ENGINETECH BB1013.

8 further parts sit outside the graded sections, with the same engine-level match.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

18 Conversion / Lower Gasket Set parts for the 2010 Honda Civic come from 8 brands — APEX, ENGINETECH, FEL-PRO and 5 other brands. The "Popular" part is APEX ACS1050.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

15 Crankshaft Main Bearing parts are listed for the 2010 Honda Civic, from TOPLINE, KING ENGINE BEARINGS, ENGINETECH and 2 other brands. KING ENGINE BEARINGS MB5259AM carries the "Popular" badge.

High Performance: 1 part, from KING ENGINE BEARINGS. A representative part number is KING ENGINE BEARINGS MB5259XPC.

The Standard Replacement section: 4 options from TOPLINE, KING ENGINE BEARINGS and ENGINETECH. KING ENGINE BEARINGS MB5259AM is listed in this group.

10 ungrouped parts are not assigned to a grade, with the same engine-level match.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

6 Crankshaft Repair Sleeve parts are listed for the 2010 Honda Civic, from SCHAEFFLER, BCA, NATIONAL and 2 other brands. BCA NS99315 carries the "Popular" badge.

Listed part numbers: BCA NS99315, NATIONAL 99315 and SCHAEFFLER SR3549, plus the other parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

36 Crankshaft Seal parts are listed for the 2010 Honda Civic, from ELRING, VICTOR REINZ, FEL-PRO and 10 other brands. FEL-PRO BS40535 carries the "Popular" badge. The notes list position, dimensions and spec qualifiers wherever the manufacturer distinguishes between variants.

This table covers the bolts that clamp the cylinder head to the block. Read more

20 Cylinder Head Bolt parts for the 2010 Honda Civic come from 9 brands — APEX, FEL-PRO, MAHLE / CLEVITE and 6 other brands. The "Popular" part is APEX AHB149.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

23 Cylinder Head Gasket parts for the 2010 Honda Civic come from 8 brands — ELRING, APEX, FEL-PRO and 5 other brands. The "Popular" part is APEX AHG160.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

25 Cylinder Head Gasket Set parts for the 2010 Honda Civic come from 8 brands — ENGINETECH, FEL-PRO, APEX and 5 other brands. The "Popular" part is ENGINETECH HO13HSB.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 2010 Honda Civic — MAHLE / CLEVITE B32774.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

KAT'S HEATERS supplies both parts for the 2010 Honda Civic.

This group includes KAT'S HEATERS 11419 and KAT'S HEATERS 28500.

This table covers the Engine covers. Read more

This group shows a single part: TECHPRO HO1228135.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Engine Kit Gasket Set parts for the 2010 Honda Civic come from 4 brands — AJUSA, TOPLINE, ENGINETECH and 1 other brand.

Listed part numbers: AJUSA 50440500, AJUSA 50546700 and AJUSA 50285100, plus the other parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts are listed for the 2010 Honda Civic, from QUALCAST, TOPLINE and ENGINETECH.

This group includes ENGINETECH EM2759, QUALCAST 1010525 and QUALCAST 1003032 and the remaining parts above.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

2 Expansion Plug parts for the 2010 Honda Civic come from QUALCAST.

This group includes QUALCAST 97110B and QUALCAST 97110.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

7 Harmonic Balancer parts for the 2010 Honda Civic come from 5 brands — DAYCO, PIONEER, SKP and 2 other brands. The "Popular" part is ULTRA-POWER 594340.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SK594340 is listed in this group.

Standard Replacement: 4 parts, from ULTRA-POWER, ATP, DAYCO and 1 other brand. A representative part number is ULTRA-POWER 594340.

2 further parts sit outside the graded sections, with the same engine-level match.

Listed part numbers: ULTRA-POWER 594340, SKP SK594340 and ATP 102323, plus the other parts above.

This table covers the Intake & Exhaust Manifold gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

This group shows a single part: ELRING 884180.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

21 Intake Manifold Gasket parts for the 2010 Honda Civic come from 8 brands — VICTOR REINZ, APEX, FEL-PRO and 5 other brands. The "Popular" part is APEX AMS1600.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

8 Intake Plenum Gasket parts are listed for the 2010 Honda Civic, from FEL-PRO, APEX, AJUSA and 3 other brands. FEL-PRO MS97041 carries the "Popular" badge.

Part numbers include FEL-PRO MS97041, AJUSA 01156700 and APEX AMS1660, among others listed above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

4 Intake Valve parts are listed for the 2010 Honda Civic, from TOPLINE, ENGINETECH and QUALCAST.

Part numbers include ENGINETECH IM4426, QUALCAST 1003031 and TOPLINE IVH42HY, among others listed above.