20 Ignition parts are listed for the 1953 Humber Pullman, in 5 part types, covering the 4.1L L6 engine. Each one has a brand, a manufacturer part number and notes that say where it fits.
On the 1953 Humber Pullman, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules. Most of the listed parts are Ignition Coil (9 parts), Spark Plug (8 parts) and Distributor Rotor (1 part). The other 2 part types cover the remaining 2 parts.
Every part on this page is matched to the 4.1L L6 — the only engine offered in the 1953 Humber Pullman.
The most listed brands for 1953 Humber Pullman ignition parts are CHAMPION (5 parts), STANDARD MOTOR PRODUCTS (4 parts) and WELLS (2 parts), plus 8 more brands. Quality grades include Copper / Nickel, Economy and Standard Replacement.
4 parts on this 1953 Humber Pullman page carry a "Popular" badge — the source catalog's flag for options frequently chosen for this vehicle — including STANDARD MOTOR PRODUCTS UC15T (Ignition Coil) and ACDELCO R44F (Spark Plug). Click any part number to see every vehicle that part fits.
Distributor Rotor
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| STANDARD MOTOR PRODUCTS | LU302 | 🇺🇸 US | View on Amazon |
This table covers the Distributor rotors. Typical signs include shudder under braking, or a lip at the outer edge. Do not put new pads on a rotor that is below minimum thickness.
This group shows a single part: STANDARD MOTOR PRODUCTS LU302.
Ignition Coil
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| STANDARD MOTOR PRODUCTS Popular | UC15T | 🇺🇸 US | T-Series | View on Amazon |
| FVP | UC15F | 🇺🇸 US | View on Amazon | |
| HOLSTEIN | 2IGC0058 | 🇺🇸 US | View on Amazon | |
| SKP | SKUC15T | 🇺🇸 US | Coil Pack | View on Amazon |
| SPECTRA PREMIUM | C622 | 🇺🇸 US | Pack | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| NGK Popular | 48863 | 🇺🇸 US | Connections May be Eyelet or Spade | View on Amazon |
| STANDARD MOTOR PRODUCTS | UC15 | 🇺🇸 US | View on Amazon | |
| UNITED MOTOR PRODUCTS | C15 | 🇺🇸 US | View on Amazon | |
| WELLS | 5C1019 | 🇺🇸 US | Used on most import products with 12 Volt system with Internal resistorUniversal 12 Volt Coil | View on Amazon |
This table covers the coils that fire each spark plug. Typical signs include a misfire that follows one cylinder, a snap in damp weather, or a coil that is swollen or cracked. Swap a suspect coil with a neighbor to confirm, then replace boots that tore on the way off.
9 Ignition Coil parts are listed for the 1953 Humber Pullman, from STANDARD MOTOR PRODUCTS, FVP, HOLSTEIN and 5 other brands. STANDARD MOTOR PRODUCTS UC15T carries the "Popular" badge.
In the Economy grade, STANDARD MOTOR PRODUCTS, FVP, HOLSTEIN and 2 other brands supply 5 parts: the catalog's value-priced group. A representative part number is STANDARD MOTOR PRODUCTS UC15T.
The Standard Replacement section lists 4 options from NGK, STANDARD MOTOR PRODUCTS, UNITED MOTOR PRODUCTS and 1 other brand — built to original-equipment specification. NGK 48863 is listed in this group.
Listed part numbers: STANDARD MOTOR PRODUCTS UC15T, FVP UC15F and HOLSTEIN 2IGC0058, plus the other parts above.
Ignition Coil Mounting Bracket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| STANDARD MOTOR PRODUCTS | CB6 | 🇺🇸 US | View on Amazon |
This table covers the brackets that mount the Ignition Coil Mounting. Typical signs include a cracked mount, a rattle, or a bracket that no longer holds alignment. Confirm position in the notes. Many brackets look alike and bolt to different corners.
This group shows a single part: STANDARD MOTOR PRODUCTS CB6.
Ignition Conversion Kit
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| WELLS | 1A4230 | 🇺🇸 US | Lucas Distributor # DVXH6A, Lobe Sensor Module, with Counter Clockwise Rotation12 Volt | View on Amazon |
This table covers the Ignition Conversion kits.
This group shows a single part: WELLS 1A4230.
Spark Plug
Summary: Notes include pre-set gaps of 0.025", 0.030", 0.032" and 0.035". Replacement brands in this table include CHAMPION, ACDELCO and AUTOLITE.
Copper / Nickel
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ACDELCO Popular | R44F | 🇺🇸 US 🇨🇦 CA | ProfessionalConventional | View on Amazon |
| CHAMPION Popular | 415 | 🇺🇸 US | Copper PlusPre-Set Gap: 0.032" | View on Amazon |
| AUTOLITE | 425 | 🇺🇸 US | Center Electrode Projection: Short ProjectionCopper Resistor | View on Amazon |
| CHAMPION | 300 | 🇺🇸 US | Copper PlusPre-Set Gap: 0.032" | View on Amazon |
| CHAMPION | 4151 | 🇺🇸 US | Copper PlusClassification: Champion Copper Plus Small Engine | View on Amazon |
Double Platinum (lasts up to 3x longer than Copper / Nickel)
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ACDELCO | 41804 | 🇺🇸 US 🇨🇦 CA | ProfessionalDouble Platinum | View on Amazon |
| CHAMPION | 7415 | 🇺🇸 US | Double Platinum PowerPre-Set Gap: 0.032" | View on Amazon |
Iridium (lasts up to 4x longer than Copper / Nickel)
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CHAMPION | 9804 | 🇺🇸 US | IridiumPre-Set Gap: 0.03" | View on Amazon |
This table covers the spark plugs for this engine. Typical signs include misfire under load, rough idle, or a flashing check-engine light. Verify the gap even on pre-gapped plugs, and replace coil boots that come off a high-mileage engine.
8 Spark Plug parts for the 1953 Humber Pullman come from 3 brands — CHAMPION, ACDELCO and AUTOLITE. The "Popular" part is ACDELCO R44F.
The Copper / Nickel section lists 5 options from CHAMPION, ACDELCO and AUTOLITE — grouped under the catalog's "Copper / Nickel" designation — the notes column spells out what sets them apart. ACDELCO R44F is listed in this group.
The Double Platinum (lasts up to 3x longer than Copper / Nickel) section lists 2 options from ACDELCO and CHAMPION — grouped under the catalog's "Double Platinum (lasts up to 3x longer than Copper / Nickel)" designation — the notes column spells out what sets them apart. ACDELCO 41804 is listed in this group.
In the Iridium (lasts up to 4x longer than Copper / Nickel) grade, CHAMPION supplies 1 part: grouped under the catalog's "Iridium (lasts up to 4x longer than Copper / Nickel)" designation — the notes column spells out what sets them apart. A representative part number is CHAMPION 9804.
This group includes ACDELCO R44F, CHAMPION 415 and AUTOLITE 425 and the remaining parts above.
Buying Ignition Parts for a 1953 Humber Pullman
On this vehicle, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules.
- Confirm you have the 4.1L L6 engine — every part on this page is matched to it.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Ignition Coil and Spark Plug .
Frequently Asked Questions
How many ignition parts fit the 1953 Humber Pullman?
Our catalog currently lists 20 ignition parts for the 1953 Humber Pullman across 5 subcategories and 11 brands, covering the 4.1L L6 engine. Each part is matched to the engine(s) it fits.
What are the signs of ignition problems on a 1953 Humber Pullman?
Common symptoms include misfires under load, rough idle, flashing check-engine light, or poor starting in damp weather. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What spark-plug gap is listed for the 1953 Humber Pullman?
Notes on this page include pre-set gaps of 0.025", 0.030", 0.032" and 0.035". Still verify against spec — even “pre-gapped” plugs should be checked before they go in.
What should I replace at the same time?
Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1953 Humber Pullman was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 1953 Humber Pullman?
Every part on this page is matched to the 4.1L L6 engine. Then gap matters even on “pre-gapped” plugs — verify against spec, and replace coil boots when they come off a high-mileage engine. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 1953 Humber Pullman
Ignition Parts for Other Humber Pullman Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.