This page lists one steering part for the 2020 International Workstar: a Power Steering Reservoir Cap from DORMAN, matched to both the 6.7L L6 DIESEL Turbocharged and the 8.9L L6 DIESEL Turbocharged.
On the 2020 International Workstar, the steering system connects driver to road through the rack, pump, tie rods, and column components.
The 2020 International Workstar was sold with both the 6.7L L6 DIESEL Turbocharged and the 8.9L L6 DIESEL Turbocharged. Every part on this page is engine-specific. Each part shows which engine(s) it fits.
The part number opens a page with every vehicle that part fits.
Power Steering Reservoir Cap
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| DORMAN Fits: 8.9L L6 DIESEL Turbocharged | 9241060 | 🇺🇸 US 🇨🇦 CA | 1.5L ReservoirDiameter: 2.3 in | View on Amazon |
This table covers the Power Steering Reservoir caps. Typical signs include a leak at the neck, a cap that will not hold pressure, or a missing tether. Match the pressure rating or thread in the notes — radiator, reservoir and fuel caps are not interchangeable.
One part is listed for the 2020 International Workstar — DORMAN 9241060.
Buying Steering Parts for a 2020 International Workstar
On this vehicle, the steering system connects driver to road through the rack, pump, tie rods, and column components.
- Match the engine first. Every steering part here is engine-specific; each row shows which engine(s) it fits.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace the inner and outer tie-rod ends together on higher-mileage vehicles, then get an alignment.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Power Steering Reservoir Cap .
Frequently Asked Questions
How many steering parts fit the 2020 International Workstar?
This page lists one steering part for the 2020 International Workstar: a Power Steering Reservoir Cap from DORMAN, covering both the 6.7L L6 DIESEL Turbocharged and the 8.9L L6 DIESEL Turbocharged.
Do steering parts differ between 2020 International Workstar engines?
Yes. Every steering part on this page is engine-specific. Each row shows which engine(s) it fits — use the filter at the top to hide the rest. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.
What are the signs of steering problems on a 2020 International Workstar?
Common symptoms include play or looseness on center, a whine when turning, fluid weeping from rack boots, or uneven tire wear on the front axle. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace the inner and outer tie-rod ends together on higher-mileage vehicles, then get an alignment.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2020 International Workstar was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 2020 International Workstar?
First match the engine — each row shows which engine(s) the part fits. Then flush old power-steering fluid when replacing a pump or rack — grit in the old fluid is the number-one cause of repeat failure. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 2020 International Workstar
Steering Parts for Other International Workstar Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.