2008 Kia Sedona Electrical Parts

This table covers the alternators that charge the battery and run the electrical load. Typical signs include dim lights at idle, a battery lamp, or a growl from the charging pulley. Load-test the battery and inspect the belt and grounds — a bad ground mimics a failed alternator. Read more

17 Alternator / Generator parts are listed for the 2008 Kia Sedona, from PURE ENERGY, TERREPOWER, WAI GLOBAL and 5 other brands. TYC 211191 carries the "Popular" badge.

In the New grade, TYC, WAI GLOBAL, FVP and 2 other brands supply 5 parts: brand-new units rather than rebuilt ones. A representative part number is TYC 211191.

In the Remanufactured grade, PURE ENERGY, BOSCH, REMY and 4 other brands supply 12 parts: factory-rebuilt units with new wear components. A representative part number is PURE ENERGY 11846.

This table covers the batteries listed by group size and specification. Typical signs include slow cranking, a battery lamp, or a no-start after the vehicle sat overnight. Confirm group size and terminal layout in the notes. Clean the posts and the ground before condemning the battery. Read more

This group shows a single part: FULLRIVER FT75035.

This table covers the terminals and clamps that connect cables to the battery posts. Read more

2 Battery Terminal parts for the 2008 Kia Sedona come from DEKA.

This group includes DEKA 00350 and DEKA 01056.

This table covers the replacement fuses for this vehicle's fuse boxes. Typical signs include one circuit dead while its neighbor still works, or a fuse that blows again as soon as you replace it. Match amperage and fuse type. A repeat blow means a short — find it before the next fuse. Read more

28 Fuse parts for the 2008 Kia Sedona come from 2 brands — BUSSMANN and LITTELFUSE. The "Popular" part is BUSSMANN ATM10. Grades run from 10 Amp through 7.5 Amp; 30 Amp is the most populated section, led by BUSSMANN and LITTELFUSE.

This table covers the ultrasonic park-aid sensors in the bumper. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

One part is listed for the 2008 Kia Sedona — STANDARD MOTOR PRODUCTS PPS256.

This table covers the speed sensors on the transmission, transfer case or ABS ring. Typical signs include a dead speedometer, harsh transmission shifts, or a code for vehicle speed. Inspect the tone wheel and the connector before replacing the sensor. Read more

33 Speed Sensor parts for the 2008 Kia Sedona come from 13 brands — VEMO, STANDARD MOTOR PRODUCTS, SKP and 10 other brands. The "Popular" part is SKP SK917686. They are grouped as Economy and Standard Replacement, with Economy the largest group at 19 parts from VEMO, SKP, BECK/ARNLEY and 4 other brands.

This table covers the starter motors that crank the engine. Typical signs include no motion, a squeal, or a motor that only runs on one speed. Confirm power, ground and the control module before replacing the motor. Read more

9 Starter Motor parts are listed for the 2008 Kia Sedona, from TYC, DENSO, WAI GLOBAL and 6 other brands. TYC 106976 carries the "Popular" badge.

New: 3 parts, from TYC, DENSO and WAI GLOBAL. A representative part number is TYC 106976.

Remanufactured: 6 parts, from ACDELCO, BOSCH, FVP and 3 other brands. A representative part number is ACDELCO 3362153.

Part numbers include TYC 106976, DENSO 2816009 and WAI GLOBAL 6976N, among others listed above.

This table covers the Starter solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

2 Starter Solenoid parts are listed for the 2008 Kia Sedona, from STANDARD MOTOR PRODUCTS and WELLS.

Part numbers include STANDARD MOTOR PRODUCTS SS873 and WELLS 1M1613.

This table covers the regulators that control alternator output voltage. Read more

This group shows a single part: STANDARD MOTOR PRODUCTS VR849.

This table covers the Yaw sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

This group shows a single part: WELLS 5S7713.