2019 Mazda CX-5 Engine Parts

This table covers the Balance Shaft sprockets. Read more

2 Balance Shaft Sprocket parts are listed for the 2019 Mazda CX-5, from CLOYES and MELLING.

This group includes CLOYES S1131 and MELLING S1246.

This table covers the Barometric pressure sensors. Typical signs include a check-engine light for MAP or fuel-rail pressure, or a limp mode under load. A vacuum leak or a clogged reference line will fake a bad pressure sensor. Read more

One part is listed for the 2019 Mazda CX-5 — STANDARD MOTOR PRODUCTS AS486.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2019 Mazda CX-5 — TOPLINE RBMA31.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts are listed for the 2019 Mazda CX-5, from AJUSA, ENGINETECH, MAHLE / CLEVITE and 1 other brand.

This group includes AJUSA 54317300, ENGINETECH MA25CSB and MAHLE / CLEVITE CS55462 and the remaining parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Crankshaft Main Bearing parts for the 2019 Mazda CX-5 come from TOPLINE.

Part numbers include TOPLINE MBMA31 and TOPLINE TWMA31.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts for the 2019 Mazda CX-5 come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

This group includes BCA NS99145, NATIONAL 99145 and WJB / INMOTION PARTS WS99145.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Crankshaft Seal parts for the 2019 Mazda CX-5 come from 5 brands — NATIONAL, WJB / INMOTION PARTS, VICTOR REINZ and 2 other brands. The "Popular" part is NATIONAL 223750.

This group includes NATIONAL 223750, WJB / INMOTION PARTS WS223750 and JAPANESE OE MD372249 and the remaining parts above.

This table covers the bolts that clamp the cylinder head to the block. Read more

3 Cylinder Head Bolt parts are listed for the 2019 Mazda CX-5, from AJUSA, APEX and FEL-PRO.

Listed part numbers: AJUSA 81066200, APEX AHB480 and FEL-PRO ES73884.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Cylinder Head Gasket parts are listed for the 2019 Mazda CX-5, from AJUSA, APEX, FEL-PRO and 1 other brand.

This group includes AJUSA 10257900, APEX AHG1426 and FEL-PRO 26831PT and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Cylinder Head Gasket Set parts are listed for the 2019 Mazda CX-5, from AJUSA, MAHLE / CLEVITE and TOPLINE.

Listed part numbers: AJUSA 52591700, MAHLE / CLEVITE HS55462 and TOPLINE HSMA31T.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

This group shows a single part: KAT'S HEATERS 11409.

This table covers the Engine covers. Read more

3 Engine Cover parts are listed for the 2019 Mazda CX-5, from TECHPRO and VARIOUS MFR.

Listed part numbers: TECHPRO MA1228125 and TECHPRO MA1228118, plus the other parts above.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Engine Kit Gasket Set parts are listed for the 2019 Mazda CX-5, from AJUSA and TOPLINE.

Part numbers include AJUSA 50540300 and TOPLINE CGSMA31T.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

2 Exhaust Valve parts for the 2019 Mazda CX-5 come from 2 brands — ENGINETECH and TOPLINE.

Listed part numbers: ENGINETECH EM3215 and TOPLINE EVMA31.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

2 Harmonic Balancer parts are listed for the 2019 Mazda CX-5, from ATP and DAYCO.

Part numbers include ATP 102485 and DAYCO PB1819N.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts are listed for the 2019 Mazda CX-5, from BECK/ARNLEY, AJUSA, APEX and 2 other brands. BECK/ARNLEY 0376241 carries the "Popular" badge.

This group includes BECK/ARNLEY 0376241, AJUSA 13272800 and APEX AMS14000 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

2 Intake Valve parts for the 2019 Mazda CX-5 come from 2 brands — ENGINETECH and TOPLINE.

Part numbers include ENGINETECH IM3216 and TOPLINE IVMA31.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

6 Motor Mount parts for the 2019 Mazda CX-5 come from 4 brands — ANCHOR, SKP, DEA / MARMON RIDE CONTROL and 1 other brand. The "Popular" part is SKP SKMA4446.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SKMA4446 is listed in this group.

In the Standard Replacement grade, ANCHOR, DEA / MARMON RIDE CONTROL and WESTAR supply 5 parts: built to original-equipment specification. A representative part number is ANCHOR 9830.

Part numbers include SKP SKMA4446, ANCHOR 9830 and ANCHOR 10272, among others listed above.

This table covers the Motor Mount inserts. Read more

One part is listed for the 2019 Mazda CX-5 — SKP SKM9830.

This table covers the Motor Mount kits. Read more

3 Motor Mount Kit parts for the 2019 Mazda CX-5 come from ANCHOR.

Listed part numbers: ANCHOR 301073, ANCHOR 301074 and ANCHOR 301085.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

46 Oil parts for the 2019 Mazda CX-5 come from 7 brands — VALVOLINE, MOBIL, PENTOSIN and 4 other brands. The "Popular" part is LIQUI MOLY 20228. They are grouped as Full Synthetic, High Mileage (>75,000 Miles) and Synthetic Blend, with Full Synthetic the largest group at 31 parts from VALVOLINE, PENTOSIN, IDEMITSU and 3 other brands.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Cooler Gasket parts are listed for the 2019 Mazda CX-5, from FEL-PRO and MAHLE / CLEVITE.

Listed part numbers: FEL-PRO ES73909 and MAHLE / CLEVITE GS34069.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts are listed for the 2019 Mazda CX-5, from DORMAN, AJUSA and JAPANESE OE.

Part numbers include AJUSA 22018700, DORMAN 095147 and DORMAN 995147CD, among others listed above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts for the 2019 Mazda CX-5 come from 4 brands — CALORSTAT, GATES, MOTORAD and 1 other brand.

Listed part numbers: CALORSTAT OC2330, GATES 31295 and MOTORAD MO147, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

10 Oil Filter parts for the 2019 Mazda CX-5 come from 8 brands — BOSCH, VARIOUS MFR, CHAMP / LUBER-FINER and 5 other brands. The "Popular" part is MOBIL M1108A.

The Economy section: 3 options from BOSCH, CHAMP / LUBER-FINER and VARIOUS MFR. BOSCH 72230WS is listed in this group.

The High Performance / Heavy Duty section lists 1 option from MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1108A is listed in this group.

Standard Replacement: 6 parts, from BOSCH, DENSO, HASTINGS / BALDWIN and 3 other brands. A representative part number is BOSCH 3300.

This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

2 Oil Filter Adapter Gasket / O-Ring parts are listed for the 2019 Mazda CX-5, from FEL-PRO and MAHLE / CLEVITE.

Part numbers include FEL-PRO 73777 and MAHLE / CLEVITE B33767.

This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

2 Oil Level Sensor parts for the 2019 Mazda CX-5 come from 2 brands — HELLA and STANDARD MOTOR PRODUCTS.

This group includes HELLA 011544031 and STANDARD MOTOR PRODUCTS FLS355.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: VICTOR REINZ 703141410.

This table covers the chains that drive the oil pump. Read more

One part is listed for the 2019 Mazda CX-5 — MELLING 1112.

This table covers the Oil Pump Chain guides. Read more

One part is listed for the 2019 Mazda CX-5 — MELLING BG7073.

This table covers the Oil Pump Chain tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: MELLING BT7090.

This table covers the Oil Pump sprockets. Read more

3 Oil Pump Sprocket parts are listed for the 2019 Mazda CX-5, from CLOYES and MELLING.

This group includes CLOYES S1130, CLOYES S1132 and MELLING S1248.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

One part is listed for the 2019 Mazda CX-5 — TOPLINE PAMA31T.

This table covers the rings that seal each piston to the cylinder wall. Read more

2 Piston Ring parts are listed for the 2019 Mazda CX-5, from HASTINGS MANUFACTURING and TOPLINE.

Part numbers include HASTINGS MANUFACTURING 2P6029 and TOPLINE RSMA31T.

This table covers the timing chains that keep the cams in time with the crank. Read more

2 Timing Chain parts are listed for the 2019 Mazda CX-5, from CLOYES and MELLING.

Listed part numbers: CLOYES C974 and MELLING 1065.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

6 Timing Chain & Component Kit parts for the 2019 Mazda CX-5 come from 3 brands — MELLING, INA and TOPLINE. The "Popular" part is MELLING 31065SX.

This group includes MELLING 31065SX, MELLING 31065S and INA ZC76342T and the remaining parts above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

7 Timing Chain Guide / Damper parts are listed for the 2019 Mazda CX-5, from CLOYES, MELLING and PREFERRED COMPONENTS INC. MELLING BT7027 carries the "Popular" badge.

Part numbers include MELLING BT7027, MELLING BG7029 and CLOYES 96106, among others listed above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

4 Timing Chain Tensioner parts for the 2019 Mazda CX-5 come from 4 brands — CLOYES, INA, MELLING and 1 other brand.

This group includes CLOYES 96101, INA ZT0269 and MELLING BT7029 and the remaining parts above.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Timing Cover Seal parts for the 2019 Mazda CX-5 come from 3 brands — MAHLE / CLEVITE, SKF and WJB / INMOTION PARTS.

Listed part numbers: MAHLE / CLEVITE 68083, SKF 16880A and WJB / INMOTION PARTS WS16880A.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

4 Timing Crank Sprocket parts for the 2019 Mazda CX-5 come from 3 brands — MELLING, CLOYES and INA.

Part numbers include CLOYES S1129, INA ZS0298 and MELLING S1245, among others listed above.

This table covers the brackets that mount the Torque Strut. Typical signs include a cracked mount, a rattle, or a bracket that no longer holds alignment. Confirm position in the notes. Many brackets look alike and bolt to different corners. Read more

This group shows a single part: DEA / MARMON RIDE CONTROL A4471.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Torque Strut Mount parts are listed for the 2019 Mazda CX-5, from ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand.

Listed part numbers: ANCHOR 10189, DEA / MARMON RIDE CONTROL A4454 and PIONEER 630002, plus the other parts above.

This table covers the turbochargers that compress intake air. Read more

2 Turbocharger parts for the 2019 Mazda CX-5 come from 2 brands — GPD and ROTOMASTER.

Listed part numbers: GPD 2511599 and ROTOMASTER M1040110N.

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Turbocharger Gasket parts are listed for the 2019 Mazda CX-5, from MAHLE / CLEVITE and AJUSA.

This group includes AJUSA JTC12633, MAHLE / CLEVITE F33814 and MAHLE / CLEVITE F33815 and the remaining parts above.

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early. Read more

This group shows a single part: AJUSA OP11317.

This table covers the Turbocharger Oil Line Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: MAHLE / CLEVITE GS34068.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts for the 2019 Mazda CX-5 come from 5 brands — VICTOR REINZ, APEX, BECK/ARNLEY and 2 other brands. The "Popular" part is VICTOR REINZ 711211800.

Part numbers include VICTOR REINZ 711211800, APEX AVC1426 and BECK/ARNLEY 0362079, among others listed above.

This table covers the Valve Cover grommets. Read more

This group shows a single part: MAHLE / CLEVITE B33646.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

2 Valve Guide parts for the 2019 Mazda CX-5 come from TOPLINE.

Listed part numbers: TOPLINE EVGMA32 and TOPLINE IVGMA32.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

2 Valve Lifter parts for the 2019 Mazda CX-5 come from 2 brands — AJUSA and TOPLINE.

Part numbers include AJUSA 85009300 and TOPLINE LIFMA32.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

4 Valve Spring Retainer Keeper parts are listed for the 2019 Mazda CX-5, from ENGINETECH, MELLING, QUALCAST and 1 other brand.

Listed part numbers: ENGINETECH EPF1104, MELLING VL1125 and QUALCAST 345024, plus the other parts above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Valve Stem Seal parts for the 2019 Mazda CX-5 come from 2 brands — AJUSA and MAHLE / CLEVITE.

This group includes AJUSA 12034200, AJUSA 12034300 and AJUSA 57070700 and the remaining parts above.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

11 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2019 Mazda CX-5 come from 10 brands — WELLS, DORMAN, SPECTRA PREMIUM and 7 other brands. The "Popular" part is DORMAN 918174.

The Economy section: 7 options from WELLS, DORMAN, SPECTRA PREMIUM and 3 other brands. DORMAN 918174 is listed in this group.

Standard Replacement: 4 parts, from BECK/ARNLEY, CLOYES, NTK and 1 other brand. A representative part number is BECK/ARNLEY 0242190.

This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Variable Valve Timing (VVT) Solenoid Gasket / Seal parts are listed for the 2019 Mazda CX-5, from MAHLE / CLEVITE and FEL-PRO.

Part numbers include FEL-PRO 73897, MAHLE / CLEVITE B33645 and MAHLE / CLEVITE B33768.

This table covers the cam phaser sprockets used by the variable-valve-timing system. Read more

2 Variable Valve Timing (VVT) Sprocket parts for the 2019 Mazda CX-5 come from STANDARD MOTOR PRODUCTS.

This group includes STANDARD MOTOR PRODUCTS VVT767 and STANDARD MOTOR PRODUCTS VVT780.