1960 MG Mga Engine Parts

This table covers the Camshaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Camshaft Bearing parts for the 1960 MG Mga come from 2 brands — DURA-BOND and ITM ENGINE COMPONENTS.

Part numbers include DURA-BOND DA2 and ITM ENGINE COMPONENTS 3C4306.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: ITM ENGINE COMPONENTS 0944002.

This table covers the wear sleeves used to restore a Cylinder seal surface. Read more

2 Cylinder Repair Sleeve parts for the 1960 MG Mga come from MELLING.

Part numbers include MELLING CSL629 and MELLING CSL729.

This table covers the Intake & Exhaust Manifold gasket sets. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Intake & Exhaust Manifold Gasket Set parts for the 1960 MG Mga come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO MS22506B, MAHLE / CLEVITE MS15234 and VICTOR REINZ 111076901.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

WESTAR supplies both parts for the 1960 MG Mga.

Listed part numbers: WESTAR EM2736 and WESTAR EM2735.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

2 Oil Filter parts are listed for the 1960 MG Mga, from HASTINGS / BALDWIN and WIX.

Listed part numbers: HASTINGS / BALDWIN LF172 and WIX 51300.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

BECK/ARNLEY supplies both parts for the 1960 MG Mga.

Part numbers include BECK/ARNLEY 0513860 and BECK/ARNLEY 0513954.

This table covers the timing chains that keep the cams in time with the crank. Read more

This group shows a single part: ITM ENGINE COMPONENTS 2352.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

One part is listed for the 1960 MG Mga — ITM ENGINE COMPONENTS 60005.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts are listed for the 1960 MG Mga, from ITM ENGINE COMPONENTS, FEL-PRO, BECK/ARNLEY and 1 other brand. FEL-PRO VS215091 carries the "Popular" badge.

This group includes FEL-PRO VS215091, BECK/ARNLEY 0360081 and ITM ENGINE COMPONENTS 0955214 and the remaining parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

ITM ENGINE COMPONENTS supplies the 4 Valve Guide parts for the 1960 MG Mga.

Listed part numbers: ITM ENGINE COMPONENTS VG751BR, ITM ENGINE COMPONENTS VG752BR and ITM ENGINE COMPONENTS VG751CI, plus the other parts above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 1960 MG Mga — ITM ENGINE COMPONENTS SS105.