1982 Morgan 4/4 Engine Parts

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

One part is listed for the 1982 Morgan 4/4 — WJB / INMOTION PARTS WS99169.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Camshaft Seal parts are listed for the 1982 Morgan 4/4, from VICTOR REINZ, NATIONAL, WJB / INMOTION PARTS and 3 other brands. NATIONAL 3774 carries the "Popular" badge. 6 parts fit every engine; the other 1 is engine-specific.

This group includes NATIONAL 3774, WJB / INMOTION PARTS WS3774 and BCA NS3774 and the remaining parts above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

5 Crankshaft Repair Sleeve parts are listed for the 1982 Morgan 4/4, from NATIONAL, WJB / INMOTION PARTS and BCA. NATIONAL 99139 carries the "Popular" badge. All of them fit every engine offered in the 1982 4/4.

Part numbers include NATIONAL 99139, BCA NS99363 and NATIONAL 99363, among others listed above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

12 Crankshaft Seal parts are listed for the 1982 Morgan 4/4, from NATIONAL, WJB / INMOTION PARTS, FEL-PRO and 2 other brands. FEL-PRO BS40158 carries the "Popular" badge. 9 parts fit every engine; the other 3 are engine-specific.

This table covers the bolts that clamp the cylinder head to the block. Read more

3 Cylinder Head Bolt parts for the 1982 Morgan 4/4 come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. 1 part fits every engine; the other 2 are engine-specific.

Listed part numbers: FEL-PRO ES72672, MAHLE / CLEVITE GS33163 and VICTOR REINZ 141003401.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Cylinder Head Gasket parts for the 1982 Morgan 4/4 come from 2 brands — FEL-PRO and VICTOR REINZ. 1 part fits every engine; the other 1 is engine-specific.

This group includes FEL-PRO 9309PT2 and VICTOR REINZ 611043500.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

2 Cylinder Head Gasket Set parts for the 1982 Morgan 4/4 come from 2 brands — FEL-PRO and VICTOR REINZ. 1 part fits every engine; the other 1 is engine-specific.

Listed part numbers: FEL-PRO HS9118PT and VICTOR REINZ 021106901.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 1982 Morgan 4/4 come from 2 brands — FEL-PRO and VICTOR REINZ. 1 part fits every engine; the other 1 is engine-specific.

Listed part numbers: FEL-PRO 9309SP2 and VICTOR REINZ 711639200.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: FEL-PRO MS90893.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

2 Oil Drain Plug Gasket parts for the 1982 Morgan 4/4 come from 2 brands — FEL-PRO and VICTOR REINZ. 1 part fits every engine; the other 1 is engine-specific.

This group includes FEL-PRO 72515 and VICTOR REINZ 711347100.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

6 Oil Filter parts are listed for the 1982 Morgan 4/4, from BOSCH, VARIOUS MFR, ACDELCO and 1 other brand. ACDELCO PF53 carries the "Popular" badge. 4 parts fit every engine; the other 2 are engine-specific.

In the Economy grade, BOSCH and VARIOUS MFR supply 2 parts: the catalog's value-priced group. A representative part number is BOSCH 72137WS.

The Standard Replacement section lists 4 options from ACDELCO, MOTORCRAFT, BOSCH and 1 other brand — built to original-equipment specification. ACDELCO PF53 is listed in this group.

This group includes ACDELCO PF53, BOSCH 72137WS and VARIOUS MFR PG4670 and the remaining parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 1982 Morgan 4/4 — FEL-PRO OS30412C.

This table covers the Timing Cover Repair Sleeve tools. This is a service tool, not a wear part — match the application in the notes. Read more

2 Timing Cover Repair Sleeve Tool parts are listed for the 1982 Morgan 4/4, from FEL-PRO and VICTOR REINZ. 1 part fits every engine; the other 1 is engine-specific.

Part numbers include FEL-PRO 16303 and VICTOR REINZ 711646100.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Valve Cover Gasket parts are listed for the 1982 Morgan 4/4, from FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ. 1 part fits every engine; the other 2 are engine-specific.

This group includes FEL-PRO VS50193C, MAHLE / CLEVITE VS39793 and VICTOR REINZ 151046201.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Valve Stem Seal parts are listed for the 1982 Morgan 4/4, from VICTOR REINZ and FEL-PRO. 2 parts fit every engine; the other 1 is engine-specific.

Part numbers include FEL-PRO SS70654, VICTOR REINZ 121005401 and VICTOR REINZ 121019501.