8 Drivetrain parts are listed for the 1957 Morris Oxford, in 3 part types, covering the 1.5L L4 engine. Each one has a brand, a manufacturer part number and notes that say where it fits.
On the 1957 Morris Oxford, the drivetrain system moves power from transmission to wheels through axles, CV joints, driveshafts, differentials and wheel-end hardware. All 8 listed parts are Universal Joint (6 parts), Differential Pinion Repair Sleeve (1 part) and Differential Pinion Seal (1 part).
The 1957 Morris Oxford came with a single engine, the 1.5L L4, and every part is verified against it.
4 brands supply drivetrain parts for the 1957 Morris Oxford, led by SKF (3 parts), GMB (2 parts) and FVP (2 parts), plus 1 more brand.
A "Popular" badge means the source catalog flagged the part as frequently chosen for the 1957 Morris Oxford. 2 parts have it, including GMB 2200600 (Universal Joint) and GMB 2200501 (Universal Joint). Each part number opens a page with every vehicle that part fits.
Differential Pinion Repair Sleeve
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| SKF | 480151 | 🇺🇸 US | Rear | View on Amazon |
This table covers the wear sleeves used to restore a grooved pinion seal surface.
One part is listed for the 1957 Morris Oxford — SKF 480151.
Differential Pinion Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| SKF | 15142 | 🇺🇸 US | Rear | View on Amazon |
This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
One part is listed for the 1957 Morris Oxford — SKF 15142.
Universal Joint
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| GMB Popular | 2200600 | 🇺🇸 US | GreasableGrease Fitting in Bearing Cap | View on Amazon |
| GMB Popular | 2200501 | 🇺🇸 US | Non-Greasable | View on Amazon |
| FVP | 2200501 | 🇺🇸 US | Non-Greasable | View on Amazon |
| FVP | 2200600 | 🇺🇸 US | GreasableGrease Fitting in Bearing Cap | View on Amazon |
| MOOG | 340 | 🇺🇸 US | Fits Rear Driveshaft at Rear Axle | View on Amazon |
| SKF | UJ340 | 🇺🇸 US | Greaseable | View on Amazon |
This table covers the U-joints in the driveshaft.
6 Universal Joint parts are listed for the 1957 Morris Oxford, from GMB, FVP, MOOG and 1 other brand. GMB 2200600 carries the "Popular" badge.
Part numbers include GMB 2200600 and GMB 2200501, among others listed above.
Buying Drivetrain Parts for a 1957 Morris Oxford
On this vehicle, the drivetrain system moves power from transmission to wheels through axles, CV joints, driveshafts, differentials and wheel-end hardware.
- Confirm you have the 1.5L L4 engine — every part on this page is matched to it.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace the differential or transfer-case fluid with any axle or seal job while everything is already open.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Universal Joint and Differential Pinion Repair Sleeve .
Frequently Asked Questions
How many drivetrain parts fit the 1957 Morris Oxford?
Our catalog currently lists 8 drivetrain parts for the 1957 Morris Oxford across 3 subcategories and 4 brands, covering the 1.5L L4 engine. Each part is matched to the engine(s) it fits.
What are the signs of drivetrain problems on a 1957 Morris Oxford?
Common symptoms include clicking in tight turns, a clunk when shifting between drive and reverse, vibration that builds with speed, or gear oil on the inside of a wheel. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace the differential or transfer-case fluid with any axle or seal job while everything is already open.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1957 Morris Oxford was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 1957 Morris Oxford?
Every part on this page is matched to the 1.5L L4 engine. Then a torn CV boot caught early is a cheap boot kit; caught late it is a whole axle — inspect before deciding which to buy. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 1957 Morris Oxford
Drivetrain Parts for Other Morris Oxford Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.