2016 Toyota Highlander Steering Parts

This table covers the steering knuckles that carry the hub, caliper and ball joints. Read more

6 Knuckle parts are listed for the 2016 Toyota Highlander, from SKP, APWI and ULTRA-POWER. SKP SK698190 carries the "Popular" badge. All of them fit every engine offered in the 2016 Highlander.

Listed part numbers: SKP SK698190, SKP SK698191 and APWI TO2024, plus the other parts above.

This table covers the Pinion Angle Adjusting bolts. Read more

2 Pinion Angle Adjusting Bolt parts for the 2016 Toyota Highlander come from 2 brands — ACDELCO and MOOG. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

Part numbers include ACDELCO 45K0205 and MOOG K100086.

This table covers the fluids specified for this steering system. Typical signs include discolored fluid, a burnt smell, or a level that keeps dropping. Use only the specification in the notes — the tables group grades because they are not interchangeable. Read more

This group shows a single part: IDEMITSU 30040106972.

This table covers the steering gear assemblies that turn the tie rods. Typical signs include fluid at a torn boot, a growl when you turn, or play that the inner tie rods do not explain. Flush the old power-steering fluid with the rack — grit in the old fluid is the usual cause of a repeat leak. Read more

5 Rack and Pinion parts are listed for the 2016 Toyota Highlander, from SKP, AAE, EDELMANN and 2 other brands. SKP SK1G2669 carries the "Popular" badge. All of them fit every engine offered in the 2016 Highlander.

In the New grade, SKP, AAE, EDELMANN and 1 other brand supply 4 parts: brand-new units rather than rebuilt ones. A representative part number is SKP SK1G2669.

In the Remanufactured grade, TERREPOWER supplies 1 part: factory-rebuilt units with new wear components. A representative part number is TERREPOWER 2110155.

This group includes SKP SK1G2669, AAE 4376N and EDELMANN 2168 and the remaining parts above.

This table covers the rubber boots that seal the inner tie-rod joints on the rack. Read more

5 Rack and Pinion Bellow parts for the 2016 Toyota Highlander come from 4 brands — MEVOTECH, BECK/ARNLEY, DORMAN and 1 other brand. The "Popular" part is MEVOTECH MS86097. Every part fits all 3 engine options (2.7L L4, 3.5L V6 and 3.5L V6 ELECTRIC/GAS).

Part numbers include MEVOTECH MS86097, BECK/ARNLEY 1033122 and DORMAN 541531, among others listed above.

This table covers the Steering shafts. Read more

2 Steering Shaft parts are listed for the 2016 Toyota Highlander, from DORMAN and LARES. All of them fit every engine offered in the 2016 Highlander.

This group includes DORMAN 425401 and LARES 691.

This table covers the Steering Wheel position sensors. Typical signs include a stall, a no-start, or a code for cam or crank correlation. Check the connector and the reluctor gap before replacing the sensor. Read more

2 Steering Wheel Position Sensor parts are listed for the 2016 Toyota Highlander, from STANDARD MOTOR PRODUCTS and WELLS. All of them fit every engine offered in the 2016 Highlander.

This group includes STANDARD MOTOR PRODUCTS SWS74 and WELLS 5S17004.

This table covers complete inner-and-outer tie-rod assemblies. Read more

BECK/ARNLEY supplies both parts for the 2016 Toyota Highlander. All of them fit every engine offered in the 2016 Highlander.

This group includes BECK/ARNLEY 1018871 and BECK/ARNLEY 1018872.

This table covers the inner and outer tie-rod ends that steer each front knuckle. Typical signs include play on center, a feathered front tire, or a boot that has split and packed with grit. Replace inner and outer ends together on a high-mileage axle, then get an alignment. Read more

34 Tie Rod End parts for the 2016 Toyota Highlander come from 11 brands — MEVOTECH, BECK/ARNLEY, SUSPENSIA and 8 other brands. The "Popular" part is MEVOTECH MS86634. Grades run from Daily Driver through Premium; Daily Driver is the most populated section, led by MEVOTECH, SUSPENSIA, DELPHI and 4 other brands.