2017 Toyota Sequoia Engine Parts

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Connecting Rod Bearing parts for the 2017 Toyota Sequoia come from 3 brands — ENGINETECH, MAHLE / CLEVITE and TOPLINE.

Part numbers include ENGINETECH BB1043, MAHLE / CLEVITE CB1985A8 and TOPLINE RBTO50.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Conversion / Lower Gasket Set parts for the 2017 Toyota Sequoia come from 5 brands — APEX, AJUSA, FEL-PRO and 2 other brands. The "Popular" part is APEX ACS8079.

Part numbers include APEX ACS8079, AJUSA 54321000 and FEL-PRO CS26394, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

4 Crankshaft Main Bearing parts are listed for the 2017 Toyota Sequoia, from TOPLINE, ENGINETECH and MAHLE / CLEVITE.

Part numbers include ENGINETECH BC1028, MAHLE / CLEVITE MS2365A and TOPLINE TWTO50, among others listed above.

This table covers the gaskets that seal the Crankshaft Main Bearing. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: ULTRA-POWER BS40679.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

5 Crankshaft Repair Sleeve parts are listed for the 2017 Toyota Sequoia, from WJB / INMOTION PARTS, NATIONAL and BCA. WJB / INMOTION PARTS WS99166 carries the "Popular" badge.

Part numbers include WJB / INMOTION PARTS WS99166, BCA NS99166 and NATIONAL 99166, among others listed above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

18 Crankshaft Seal parts are listed for the 2017 Toyota Sequoia, from VICTOR REINZ, AJUSA, FEL-PRO and 8 other brands. AJUSA 15019600 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

6 Cylinder Head Bolt parts for the 2017 Toyota Sequoia come from 6 brands — AJUSA, MAHLE / CLEVITE, APEX and 3 other brands. The "Popular" part is AJUSA 81042100.

This group includes AJUSA 81042100, MAHLE / CLEVITE GS33754 and APEX AHB879 and the remaining parts above.

This table covers the Cylinder Head Bolt washers. Read more

This group shows a single part: MAHLE / CLEVITE GS33354.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

12 Cylinder Head Gasket parts for the 2017 Toyota Sequoia come from 6 brands — FEL-PRO, MAHLE / CLEVITE, AJUSA and 3 other brands. The "Popular" part is FEL-PRO 26393PT.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Cylinder Head Gasket Set parts for the 2017 Toyota Sequoia come from 6 brands — FEL-PRO, APEX, AJUSA and 3 other brands. The "Popular" part is APEX AHS8079.

Part numbers include APEX AHS8079, FEL-PRO HS26394PT and AJUSA 52457700, among others listed above.

This table covers the Cylinder Head Spacer shims. Read more

2 Cylinder Head Spacer Shim parts for the 2017 Toyota Sequoia come from SBI.

Part numbers include SBI 2302204L and SBI 2302204R.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

KAT'S HEATERS supplies both parts for the 2017 Toyota Sequoia.

Listed part numbers: KAT'S HEATERS 11813 and KAT'S HEATERS 28813.

This table covers the Engine covers. Read more

This group shows a single part: TECHPRO TO1228243.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

3 Engine Kit Gasket Set parts for the 2017 Toyota Sequoia come from 2 brands — AJUSA and TOPLINE.

This group includes AJUSA 50547600, AJUSA 50583500 and TOPLINE CGSTO50.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts are listed for the 2017 Toyota Sequoia, from MELLING, ENGINETECH, QUALCAST and 2 other brands. MELLING V3087 carries the "Popular" badge.

This group includes MELLING V3087, ENGINETECH EM4457 and QUALCAST 1013087 and the remaining parts above.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

5 Harmonic Balancer parts for the 2017 Toyota Sequoia come from 5 brands — SKP, ATP, DAYCO and 2 other brands. The "Popular" part is SKP SK594703.

The Economy section lists 1 option from SKP — the catalog's value-priced group. SKP SK594703 is listed in this group.

In the Standard Replacement grade, ATP, DAYCO and ULTRA-POWER supply 3 parts: built to original-equipment specification. A representative part number is ATP 102416.

1 further part sits outside the graded sections, with the same engine-level match.

Listed part numbers: SKP SK594703, ATP 102416 and DAYCO PB1650N, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Intake Manifold Gasket parts for the 2017 Toyota Sequoia come from 4 brands — FEL-PRO, AJUSA, MAHLE / CLEVITE and 1 other brand. The "Popular" part is FEL-PRO MS97044.

Listed part numbers: FEL-PRO MS97044, MAHLE / CLEVITE MS19736 and AJUSA 13254700, plus the other parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Intake Valve parts are listed for the 2017 Toyota Sequoia, from MELLING, ENGINETECH, QUALCAST and 2 other brands. MELLING V3086 carries the "Popular" badge.

This group includes MELLING V3086, ENGINETECH IM4456 and QUALCAST 1013086 and the remaining parts above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

8 Motor Mount parts are listed for the 2017 Toyota Sequoia, from ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand. ANCHOR 9693 carries the "Popular" badge.

Listed part numbers: ANCHOR 9693, ANCHOR 9692 and DEA / MARMON RIDE CONTROL A4267, plus the other parts above.

This table covers the Motor Mount kits. Read more

4 Motor Mount Kit parts are listed for the 2017 Toyota Sequoia, from ANCHOR and WESTAR.

Listed part numbers: ANCHOR 300151, ANCHOR 300149 and WESTAR ETK087, plus the other parts above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

33 Oil parts are listed for the 2017 Toyota Sequoia, from VALVOLINE, LIQUI MOLY, MOBIL and 3 other brands. LIQUI MOLY 22044 carries the "Popular" badge. Full Synthetic and High Mileage (>75,000 Miles) are all represented, and Full Synthetic alone accounts for 26 parts.

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant. Read more

3 Oil Cooler parts are listed for the 2017 Toyota Sequoia, from ACKOJA and NISSENS.

Listed part numbers: ACKOJA A70600025, ACKOJA A70600019 and NISSENS 91443.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: MAHLE / CLEVITE GS33926.

This table covers the drain plugs in the oil pan. Read more

5 Oil Drain Plug parts are listed for the 2017 Toyota Sequoia, from DORMAN, AGS, BECK/ARNLEY and 1 other brand. DORMAN 090038 carries the "Popular" badge.

Listed part numbers: DORMAN 090038, AGS ODP00011 and BECK/ARNLEY 0160116, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Drain Plug Gasket parts for the 2017 Toyota Sequoia come from 6 brands — DORMAN, MAHLE / CLEVITE, APEX and 3 other brands. The "Popular" part is DORMAN 095156.

Listed part numbers: DORMAN 095156, MAHLE / CLEVITE 2051 and APEX ADP1902, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

5 Oil Filler Cap parts are listed for the 2017 Toyota Sequoia, from DORMAN, CALORSTAT, GATES and 2 other brands. DORMAN 84111 carries the "Popular" badge.

Part numbers include DORMAN 84111, CALORSTAT OC2312 and GATES 31285, among others listed above.

This table covers the gaskets that seal the Oil Filler Cap. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 00519100.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

22 Oil Filter parts are listed for the 2017 Toyota Sequoia, from CHAMP / LUBER-FINER, FVP, VARIOUS MFR and 14 other brands. MOBIL M1C453A carries the "Popular" badge.

Economy: 8 parts, from CHAMP / LUBER-FINER, FRAM, FVP and 4 other brands. A representative part number is CHAMP / LUBER-FINER P979.

In the High Performance / Heavy Duty grade, MOBIL and WIX supply 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is MOBIL M1C453A.

The Standard Replacement section: 12 options from ACDELCO, BOSCH, WIX and 9 other brands. ACDELCO PF466G is listed in this group.

This table covers the Oil Filter covers. Read more

6 Oil Filter Cover parts for the 2017 Toyota Sequoia come from 5 brands — MOTORAD, DORMAN, SKP and 2 other brands. The "Popular" part is DORMAN 917016.

Listed part numbers: DORMAN 917016, SKP SK917016 and AUTOTECNICA TY1420831, plus the other parts above.

This table covers the oil pans that hold the engine's oil sump. Read more

5 Oil Pan parts for the 2017 Toyota Sequoia come from 5 brands — SKP, AUTOTECNICA, DORMAN and 2 other brands. The "Popular" part is SKP SK264475.

Part numbers include SKP SK264475, AUTOTECNICA TY1416310 and DORMAN 264475, among others listed above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Pan Gasket parts are listed for the 2017 Toyota Sequoia, from APEX, FEL-PRO, MAHLE / CLEVITE and 1 other brand.

Part numbers include APEX AOP879, FEL-PRO OS30803 and MAHLE / CLEVITE OS32372, among others listed above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

5 Oil Pump parts are listed for the 2017 Toyota Sequoia, from MELLING, ENGINETECH, SEALED POWER and 2 other brands. MELLING M544 carries the "Popular" badge.

Listed part numbers: MELLING M544, ENGINETECH EP1028 and SEALED POWER 22443692, plus the other parts above.

This table covers the O-rings that seal the oil-pump pickup tube. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

One part is listed for the 2017 Toyota Sequoia — FEL-PRO 73595.

This table covers the Oil Pump repair kits. Read more

2 Oil Pump Repair Kit parts for the 2017 Toyota Sequoia come from 2 brands — ITM ENGINE COMPONENTS and MELLING.

This group includes ITM ENGINE COMPONENTS 0571056K and MELLING K544.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

2 Piston parts for the 2017 Toyota Sequoia come from 2 brands — SEALED POWER and TOPLINE.

In the Premium grade, SEALED POWER supplies 1 part: a step above OE specification in materials, tolerances or warranty terms. A representative part number is SEALED POWER 13624CPA.

Standard Replacement: 1 part, from TOPLINE. A representative part number is TOPLINE PATO50L.

Part numbers include SEALED POWER 13624CPA and TOPLINE PATO50L.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2017 Toyota Sequoia — TOPLINE PBH36.

This table covers the rings that seal each piston to the cylinder wall. Read more

4 Piston Ring parts for the 2017 Toyota Sequoia come from 3 brands — HASTINGS MANUFACTURING, SEALED POWER and TOPLINE.

Premium: 1 part, from SEALED POWER. A representative part number is SEALED POWER E1002KC.

Standard Replacement: 3 parts, from HASTINGS MANUFACTURING and TOPLINE. A representative part number is HASTINGS MANUFACTURING 2C4586.

This group includes SEALED POWER E1002KC, HASTINGS MANUFACTURING 2C4586 and HASTINGS MANUFACTURING 2C4586S and the remaining parts above.

This table covers the Thrust washers. Read more

2 Thrust Washer parts are listed for the 2017 Toyota Sequoia, from ENGINETECH and MAHLE / CLEVITE.

Part numbers include ENGINETECH TW1028 and MAHLE / CLEVITE TW728S.

This table covers the timing chains that keep the cams in time with the crank. Read more

11 Timing Chain parts for the 2017 Toyota Sequoia come from 6 brands — MELLING, S.A. GEAR, CLOYES and 3 other brands. The "Popular" part is MELLING 1026.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

14 Timing Chain & Component Kit parts are listed for the 2017 Toyota Sequoia, from PREFERRED COMPONENTS INC, S.A. GEAR, CLOYES and 6 other brands. CLOYES 90922SX carries the "Popular" badge.

Economy: 7 parts, from PREFERRED COMPONENTS INC, S.A. GEAR, GATES and 2 other brands. A representative part number is GATES CHK130.

The Standard Replacement section: 7 options from CLOYES, MELLING, INA and 1 other brand. CLOYES 90922SX is listed in this group.

This table covers the guides and dampers that keep the timing chain on its path. Read more

17 Timing Chain Guide / Damper parts for the 2017 Toyota Sequoia come from 5 brands — MELLING, CLOYES, PREFERRED COMPONENTS INC and 2 other brands. The "Popular" part is MELLING BG5078.