1973 Triumph GT6 Engine Parts

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 1973 Triumph GT6 — ITM ENGINE COMPONENTS 6B2406.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 1973 Triumph GT6 — ITM ENGINE COMPONENTS 0925601.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: ITM ENGINE COMPONENTS 4M2407.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts for the 1973 Triumph GT6 come from 3 brands — NATIONAL, SCHAEFFLER and WJB / INMOTION PARTS.

This group includes NATIONAL 99199, SCHAEFFLER SR3511 and WJB / INMOTION PARTS WS99199.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Crankshaft Seal parts for the 1973 Triumph GT6 come from 5 brands — NATIONAL, BCA, ITM ENGINE COMPONENTS and 2 other brands. The "Popular" part is NATIONAL 472397.

This group includes NATIONAL 472397, BCA NS472397 and ITM ENGINE COMPONENTS 1504013 and the remaining parts above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: ITM ENGINE COMPONENTS RV34333.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

5 Oil Filter parts for the 1973 Triumph GT6 come from 5 brands — PUROLATOR, WIX, HASTINGS / BALDWIN and 2 other brands. The "Popular" part is WIX 51313.

The Economy section lists 1 option from PUROLATOR — the catalog's value-priced group. PUROLATOR L10222 is listed in this group.

In the Standard Replacement grade, WIX, HASTINGS / BALDWIN, MAHLE / CLEVITE and 1 other brand supply 4 parts: built to original-equipment specification. A representative part number is WIX 51313.

Listed part numbers: WIX 51313, PUROLATOR L10222 and HASTINGS / BALDWIN LF338, plus the other parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: ITM ENGINE COMPONENTS 0995602.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

This group shows a single part: ITM ENGINE COMPONENTS 057320.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: ITM ENGINE COMPONENTS RB890.

This table covers the Thrust washers. Read more

This group shows a single part: ITM ENGINE COMPONENTS 1T2407.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

2 Timing Belt Pulley parts for the 1973 Triumph GT6 come from BECK/ARNLEY.

This group includes BECK/ARNLEY 0513860 and BECK/ARNLEY 0513954.

This table covers the timing chains that keep the cams in time with the crank. Read more

3 Timing Chain parts are listed for the 1973 Triumph GT6, from INA, ITM ENGINE COMPONENTS and S.A. GEAR.

This group includes INA ZC94013, ITM ENGINE COMPONENTS 1362 and S.A. GEAR 3SR62.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

This group shows a single part: SKF 99199.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts for the 1973 Triumph GT6 come from 2 brands — ITM ENGINE COMPONENTS and SKF.

Listed part numbers: ITM ENGINE COMPONENTS 1505601 and SKF 19993.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Valve Cover Gasket parts for the 1973 Triumph GT6 come from 4 brands — FEL-PRO, ITM ENGINE COMPONENTS, MAHLE / CLEVITE and 1 other brand.

This group includes FEL-PRO VS26040, ITM ENGINE COMPONENTS 0935601 and MAHLE / CLEVITE VS30029 and the remaining parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

4 Valve Guide parts for the 1973 Triumph GT6 come from ITM ENGINE COMPONENTS.

Listed part numbers: ITM ENGINE COMPONENTS VG174CI, ITM ENGINE COMPONENTS VG538CI and ITM ENGINE COMPONENTS VG174BR, plus the other parts above.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

One part is listed for the 1973 Triumph GT6 — ITM ENGINE COMPONENTS VS438.

This table covers the Valve Spring retainers. Read more

One part is listed for the 1973 Triumph GT6 — ITM ENGINE COMPONENTS 051309.