2025 Audi A1 Engine Parts

Engine:

Showing parts for every engine. Select an engine to see only what fits.

This page lists 22 engine parts for the 2025 Audi A1, across 14 part types, covering both the 1.5L L4 Turbocharged and the 999cc L3 Turbocharged. Every part shows its brand, manufacturer part number and fitment notes.

On the 2025 Audi A1, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. 8 parts of the 22 listed are Camshaft Seal (3 parts), Oil Drain Plug (3 parts) and Crankshaft Seal (2 parts). The other 11 part types cover the remaining 14 parts.

Camshaft Seal

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 242650
🇲🇽 MX
Dust Cover: with dust LipHeight [MM]: 7
Fitment notes — ELRING 242650
Dust Cover: with dust LipHeight [MM]: 7Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)Swirl Type: Right-hand Twist
Body code: 8X
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 523650
🇲🇽 MX
Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)Swirl Type: Left-hand Twist
Fitment notes — ELRING 523650
Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)Swirl Type: Left-hand Twist
Body code: 8X
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 814110
🇲🇽 MX
Material: FPM (Fluoride Rubber)
Fitment notes — ELRING 814110
Material: FPM (Fluoride Rubber)
Body code: 8X
View on
Amazon

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Connecting Rod Bolt

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 038820
🇲🇽 MX
Bolt Head-/Nut Design: Male Star
Fitment notes — ELRING 038820
Bolt Head-/Nut Design: Male Star
Body code: 8X
View on
Amazon

This table covers the Connecting Rod bolts.

Crankshaft Seal

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 248270
🇲🇽 MX
Material: PTFE (polytetrafluoroethylene)Radial Shaft Seal Design: ASW
Fitment notes — ELRING 248270
Material: PTFE (polytetrafluoroethylene)Radial Shaft Seal Design: ASW
Body code: 8X
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 523120
🇲🇽 MX
Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)Radial Shaft Seal Design: IWD
Fitment notes — ELRING 523120
Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)Radial Shaft Seal Design: IWDSwirl Type: Left-hand Twist
Body code: 8X
View on
Amazon

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Crankshaft Seal Gasket

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 092360
🇲🇽 MX
Body code: 8X
View on
Amazon

This table covers the gaskets that seal the Crankshaft Seal. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Intake Manifold Gasket

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 470370
🇲🇽 MX
Inner Diameter [mm]: 45
Fitment notes — ELRING 470370
Inner Diameter [mm]: 45
Body code: 8X
View on
Amazon

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Oil Cooler Seal

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 315540
🇲🇽 MX
Material: HNBR (hydrogenated nitrile butadiene rubber)
Fitment notes — ELRING 315540
Material: HNBR (hydrogenated nitrile butadiene rubber)
Body code: 8X
View on
Amazon

This table covers the seals at the Oil Cooler. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Oil Drain Plug

Brand Part Number Markets Notes Buy
DORMAN Fits: all 2025 A1 engines 090169
🇲🇽 MX
StandardThread Size
Fitment notes — DORMAN 090169
StandardThread SizeM14-1.50Under-Head Length: 16mmHead Size: 19mmHead Style: Hex
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 589640
🇲🇽 MX
without Seal RingSpanner Size: 19 mm
Fitment notes — ELRING 589640
without Seal RingSpanner Size: 19 mm
Body code: 8X
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 878070
🇲🇽 MX
with Seal RingBolt Head-/Nut Design: Male Hex
Fitment notes — ELRING 878070
with Seal RingBolt Head-/Nut Design: Male HexThread Size: M14X1,5x16
Body code: 8X
View on
Amazon

This table covers the drain plugs in the oil pan.

Oil Drain Plug Gasket

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 813036
🇲🇽 MX
Material: CopperOuter Diameter [MM]: 20
Fitment notes — ELRING 813036
Material: CopperOuter Diameter [MM]: 20Thickness [MM]: 2
Body code: 8X
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 591840
🇲🇽 MX
Material: Steel
Fitment notes — ELRING 591840
Material: Steel
Body code: 8X
View on
Amazon

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Oil Filter

Brand Part Number Markets Notes Buy
MOBIL Fits: all 2025 A1 engines M1102A
🇲🇽 MX
Extended Performance
View on
Amazon

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.

Oil Level Sensor Gasket / O-Ring

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 351210
🇲🇽 MX
Colour: BlackMaterial: AEM (Ethylene Acrylate Rubber)
Fitment notes — ELRING 351210
Colour: BlackMaterial: AEM (Ethylene Acrylate Rubber)
Body code: 8X
View on
Amazon

This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.

Oil Pump Gasket

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 245730
🇲🇽 MX
frontal sidedBody code: 8X
View on
Amazon

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Turbocharger Gasket

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 268402
🇲🇽 MX
Inner Diameter [MM]: 44
Fitment notes — ELRING 268402
Inner Diameter [MM]: 44
Body code: 8X
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 847040
🇲🇽 MX
Inner Diameter [MM]: 65
Fitment notes — ELRING 847040
Inner Diameter [MM]: 65
Body code: 8X
View on
Amazon

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Turbocharger Mounting Hardware

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 100090
🇲🇽 MX
with gaskets/sealswith Bolts/Screws
Fitment notes — ELRING 100090
with gaskets/sealswith Bolts/Screwsfor OE Number: 2554592
Body code: 8X
View on
Amazon

This table covers the fasteners that mount the turbocharger.

Valve Stem Seal

Brand Part Number Markets Notes Buy
ELRING Fits: 1.5L L4 Turbocharged 308610
🇲🇽 MX
Height [MM]: 10,3Outer Diameter [MM]: 11
Fitment notes — ELRING 308610
Height [MM]: 10,3Outer Diameter [MM]: 11Outside Diameter: 11.0 mm
Body code: 8X
View on
Amazon
ELRING Fits: 1.5L L4 Turbocharged 302890
🇲🇽 MX
Height [MM]: 9,7Thickness: 9.7 mm
Fitment notes — ELRING 302890
Height [MM]: 9,7Thickness: 9.7 mm
Body code: 8X
View on
Amazon

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Buying Engine Parts for a 2025 Audi A1

On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.

  • Match the engine first. Some engine parts fit every engine; others are engine-specific. Each row shows which engine(s) it fits.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Camshaft Seal and Oil Drain Plug .

Frequently Asked Questions

How many engine parts fit the 2025 Audi A1?

Our catalog currently lists 22 engine parts for the 2025 Audi A1 across 14 subcategories and 3 brands, covering both the 1.5L L4 Turbocharged and the 999cc L3 Turbocharged. Each part is matched to the engine(s) it fits.

Do engine parts differ between 2025 Audi A1 engines?

Some do. 2 parts fit every engine; the other 20 are engine-specific. Each row (and the filter at the top) shows which. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.

What are the signs of engine problems on a 2025 Audi A1?

Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What should I replace at the same time?

Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2025 Audi A1 was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 2025 Audi A1?

First match the engine — each row shows which engine(s) the part fits. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 2025 Audi A1

Engine Parts for Other Audi A1 Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.