261 Engine parts are listed for the 2021 BMW X6, in 54 part types, covering both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. Each one has a brand, a manufacturer part number and notes that say where it fits.
On the 2021 BMW X6, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. 49 parts of the 261 listed are Oil Filter (24 parts), Crankshaft Seal (13 parts) and Oil (12 parts). The other 51 part types cover the remaining 212 parts.
The 2021 BMW X6 was sold with both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. 13 parts fit every engine; the other 248 are engine-specific. Each part shows which engine(s) it fits.
The most listed brands for 2021 BMW X6 engine parts are ELRING (64 parts), AJUSA (45 parts) and REIN (18 parts), plus 45 more brands. Quality grades include Standard Replacement, Economy and Daily Driver.
36 parts on this 2021 BMW X6 page carry a "Popular" badge — the source catalog's flag for options frequently chosen for this vehicle — including ELRING 575970 (Crankshaft Seal) and ELRING 233380 (Cylinder Head Bolt). Click any part number to see every vehicle that part fits.
Camshaft Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 4.4L V8 Turbocharged | TCS46149 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front | View on Amazon |
This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
One part is listed for the 2021 BMW X6 — FEL-PRO TCS46149.
Conversion / Lower Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 54302500 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 54304500 | 🇺🇸 US 🇨🇦 CA | M50i Model | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 54330900 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 565620 | 🇺🇸 US 🇨🇦 CA | with Crankshaft Seal | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 794700 | 🇺🇸 US 🇨🇦 CA | with Crankshaft Seal | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 113340 | 🇺🇸 US 🇨🇦 CA | with Crankshaft Seal, Oil Sump Gasket | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 648590 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | with Crankshaft Seal | View on Amazon |
This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
7 Conversion / Lower Gasket Set parts for the 2021 BMW X6 come from 2 brands — ELRING and AJUSA.
This group includes AJUSA 54302500, AJUSA 54304500 and AJUSA 54330900 and the remaining parts above.
Crankshaft Main Bearing
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| KING ENGINE BEARINGS Fits: 3.0L L6 Turbocharged | MB7779SM | 🇺🇸 US 🇨🇦 CA | BI-Metal (strengthened aluminum)Set | View on Amazon |
| KING ENGINE BEARINGS Fits: 3.0L L6 Turbocharged | MB7779MC | 🇺🇸 US 🇨🇦 CA | BI-Metal (strengthened aluminum)Set | View on Amazon |
This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly.
KING ENGINE BEARINGS supplies both parts for the 2021 BMW X6.
Listed part numbers: KING ENGINE BEARINGS MB7779SM and KING ENGINE BEARINGS MB7779MC.
Crankshaft Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 3.0L L6 Turbocharged | 575970 | 🇺🇸 US 🇨🇦 CA | Height [MM]: 8Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) | View on Amazon |
| ELRING Popular Fits: 3.0L L6 Turbocharged | 492060 | 🇺🇸 US 🇨🇦 CA | Dust Cover: with Dust LipMaterial: FPM (Fluoride Rubber) | View on Amazon |
| ELRING Popular Fits: 4.4L V8 Turbocharged | 359260 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | with Mounting Sleeve | View on Amazon |
| ELRING Popular Fits: 4.4L V8 Turbocharged | 284460 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Swirl Type: Left-hand Twist | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 584160 | 🇺🇸 US 🇨🇦 CA | Material: FPM (fluoride rubber)Swirl Type: Right-hand Twist | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 586550 | 🇺🇸 US 🇨🇦 CA | with Mounting SleeveMaterial: PTFE (polytetrafluoroethylene) | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 656160 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)Swirl Type: Right-hand Twist | View on Amazon |
| FEL-PRO Fits: 4.4L V8 Turbocharged | BS40780 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Rear | View on Amazon |
| MAHLE / CLEVITE Fits: 4.4L V8 Turbocharged | 68040 | 🇺🇸 US 🇨🇦 CA | RubberIncludes Flange | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 813700200 | 🇺🇸 US 🇨🇦 CA | Front | View on Amazon |
| VICTOR REINZ Fits: all 2021 X6 engines | 812941200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Material: ACM (Polyacrylate) | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 811044800 | 🇺🇸 US 🇨🇦 CA | RearReplaces OE Part Number(s) 11148602594 | View on Amazon |
| VICTOR REINZ Fits: 4.4L V8 Turbocharged | 811040300 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RearN63B44D Engine | View on Amazon |
This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
13 Crankshaft Seal parts are listed for the 2021 BMW X6, from ELRING, VICTOR REINZ, FEL-PRO and 1 other brand. ELRING 575970 carries the "Popular" badge. 1 part fits every engine; the other 12 are engine-specific.
Cylinder Head Bolt
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 3.0L L6 Turbocharged | 233380 | 🇺🇸 US 🇨🇦 CA | SetBolt Head-/Nut Design: Male Torx | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 81069200 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 81061000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ELRING Fits: 3.0L L6 Turbocharged | 794480 | 🇺🇸 US 🇨🇦 CA | SetBolt Head-/Nut Design: Female Torx | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 469830 | 🇺🇸 US 🇨🇦 CA | SetBolt Head-/Nut Design: Male Torx | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 249210 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Set | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 141226103 | 🇺🇸 US 🇨🇦 CA | Set | View on Amazon |
This table covers the bolts that clamp the cylinder head to the block.
7 Cylinder Head Bolt parts for the 2021 BMW X6 come from 3 brands — ELRING, AJUSA and VICTOR REINZ. The "Popular" part is ELRING 233380.
Part numbers include ELRING 233380, AJUSA 81069200 and AJUSA 81061000, among others listed above.
Cylinder Head Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 3.0L L6 Turbocharged | 793491 | 🇺🇸 US 🇨🇦 CA | Installed Thickness [MM]: 0,81Material: Multi-Layer Steel (MLS) | View on Amazon |
| ELRING Popular Fits: 3.0L L6 Turbocharged | 739501 | 🇺🇸 US 🇨🇦 CA | Installed Thickness [MM]: 1,11Material: Multi-Layer Steel (MLS) | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 10248900 | 🇺🇸 US 🇨🇦 CA | Multi Layered Steel | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 10248910 | 🇺🇸 US 🇨🇦 CA | Multi Layered Steel | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 10249900 | 🇺🇸 US 🇨🇦 CA | Multi Layered SteelThickness: 1 MM | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 10249910 | 🇺🇸 US 🇨🇦 CA | Multi Layered SteelThickness: 0.7 MM | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 10272400 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Multi Layered Steel | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 10272410 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Multi Layered Steel | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 52607100 | 🇺🇸 US 🇨🇦 CA | RightM50i Model | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 611084400 | 🇺🇸 US 🇨🇦 CA | 0.80mm Thickwith Engine Code B58B30C | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 611084410 | 🇺🇸 US 🇨🇦 CA | 1.10mm Thickwith Engine Code B58B30C | View on Amazon |
This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
11 Cylinder Head Gasket parts for the 2021 BMW X6 come from 3 brands — AJUSA, ELRING and VICTOR REINZ. The "Popular" part is ELRING 793491.
Cylinder Head Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 52561500 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 52607000 | 🇺🇸 US 🇨🇦 CA | Complete Set | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 52635100 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Complete Set | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 113980 | 🇺🇸 US 🇨🇦 CA | Includes Valve Stem Seals | View on Amazon |
This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
4 Cylinder Head Gasket Set parts for the 2021 BMW X6 come from 2 brands — AJUSA and ELRING.
Part numbers include AJUSA 52561500, AJUSA 52607000 and AJUSA 52635100, among others listed above.
Engine Cover
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| TECHPRO Fits: all 2021 X6 engines | BM1228191 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front LowerG05 | View on Amazon |
| TECHPRO Fits: 4.4L V8 Turbocharged | BM1228197 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front LowerM Competition or M Model | View on Amazon |
This table covers the Engine covers.
2 Engine Cover parts for the 2021 BMW X6 come from TECHPRO. 1 part fits every engine; the other 1 is engine-specific.
This group includes TECHPRO BM1228191 and TECHPRO BM1228197.
Engine Kit Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 50515000 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 50549100 | 🇺🇸 US 🇨🇦 CA | M50i Model | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 50573100 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
3 Engine Kit Gasket Set parts for the 2021 BMW X6 come from AJUSA.
Part numbers include AJUSA 50515000, AJUSA 50549100 and AJUSA 50573100.
Harmonic Balancer Bolt
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Fits: 3.0L L6 Turbocharged | HWB0074 | 🇺🇸 US 🇨🇦 CA | 10 x 65mm | View on Amazon |
This table covers the Harmonic Balancer bolts.
One part is listed for the 2021 BMW X6 — REIN HWB0074.
Intake Manifold Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 3.0L L6 Turbocharged | 584600 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
| ELRING Popular Fits: 3.0L L6 Turbocharged | 076500 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 13313000 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 13314000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ELRING Fits: 3.0L L6 Turbocharged | 546900 | 🇺🇸 US 🇨🇦 CA | Material: Hydrogenated Nitrile Rubber (HNBR) | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 648280 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M CompetitionBody code: F96 | View on Amazon |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | MS20642 | 🇺🇸 US 🇨🇦 CA | SetMolded Rubber | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 711737500 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
8 Intake Manifold Gasket parts for the 2021 BMW X6 come from 4 brands — ELRING, AJUSA, MAHLE / CLEVITE and 1 other brand. The "Popular" part is ELRING 584600.
This group includes ELRING 584600, ELRING 076500 and AJUSA 13313000 and the remaining parts above.
Motor Mount
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ANCHOR Popular Fits: all 2021 X6 engines | 10258 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front RightHydraulic | View on Amazon |
| ANCHOR Popular Fits: 3.0L L6 Turbocharged | 10260 | 🇺🇸 US 🇨🇦 CA | Front LeftHydraulic | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 3.0L L6 Turbocharged | A70079 | 🇺🇸 US 🇨🇦 CA | Left | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 3.0L L6 Turbocharged | A70084 | 🇺🇸 US 🇨🇦 CA | Right | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 4.4L V8 Turbocharged | A70085 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Left | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 4.4L V8 Turbocharged | A70086 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Right | View on Amazon |
| PIONEER Fits: all 2021 X6 engines | 610258 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front Right | View on Amazon |
| PIONEER Fits: 3.0L L6 Turbocharged | 611260 | 🇺🇸 US 🇨🇦 CA | Front Left | View on Amazon |
| WESTAR Fits: 3.0L L6 Turbocharged | EM7560 | 🇺🇸 US 🇨🇦 CA | Right | View on Amazon |
This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes.
9 Motor Mount parts are listed for the 2021 BMW X6, from DEA / MARMON RIDE CONTROL, ANCHOR, PIONEER and 1 other brand. ANCHOR 10258 carries the "Popular" badge. 2 parts fit every engine; the other 7 are engine-specific.
Listed part numbers: ANCHOR 10258, ANCHOR 10260 and DEA / MARMON RIDE CONTROL A70079, plus the other parts above.
Motor Mount Kit
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ANCHOR Fits: 3.0L L6 Turbocharged | 301044 | 🇺🇸 US | RWD | View on Amazon |
This table covers the Motor Mount kits.
One part is listed for the 2021 BMW X6 — ANCHOR 301044.
Oil
Summary: Notes list SAE 0W-20, SAE 0W-30 and SAE 5W-30. Confirm the engine and the weight on the filler cap before you buy. Replacement brands in this table include LIQUI MOLY, VALVOLINE and PENTOSIN.
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| LIQUI MOLY Popular Fits: 3.0L L6 Turbocharged | 22044 | 🇺🇸 US 🇨🇦 CA | Top Tec 6600 0W-201 Liter | View on Amazon |
| LIQUI MOLY Popular Fits: 3.0L L6 Turbocharged | 22046 | 🇺🇸 US 🇨🇦 CA | Top Tec 6600 0W-205 Liter | View on Amazon |
| MOBIL Popular Fits: all 2021 X6 engines | 127568 | 🇺🇸 US | ESP 5W30 1 Quart | View on Amazon |
| VALVOLINE Popular Fits: 4.4L V8 Turbocharged | 787301 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | European Vehicle Full Synthetic SAE 5W-301 Quart | View on Amazon |
| LIQUI MOLY Fits: 3.0L L6 Turbocharged | 22048 | 🇺🇸 US 🇨🇦 CA | Top Tec 6600 0W-2020 Liter | View on Amazon |
| LIQUI MOLY Fits: 4.4L V8 Turbocharged | 22260 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Special Tec B FE 0W-301 Liter | View on Amazon |
| LIQUI MOLY Fits: 4.4L V8 Turbocharged | 22261 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Special Tec B FE 0W-305 Liter | View on Amazon |
| LIQUI MOLY Fits: 4.4L V8 Turbocharged | 22269 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Special Tec B FE 0W-3020 Liter | View on Amazon |
| PENTOSIN Fits: 3.0L L6 Turbocharged | 8044317 | 🇺🇸 US 🇨🇦 CA | Pento Speed FESAE 0W-20 | View on Amazon |
| PENTOSIN Fits: 3.0L L6 Turbocharged | 8044319 | 🇺🇸 US 🇨🇦 CA | Pento Speed FESAE 0W-20 | View on Amazon |
| VALVOLINE Fits: 3.0L L6 Turbocharged | 888048 | 🇺🇸 US 🇨🇦 CA | European Vehicle Full Synthetic SAE 0W-201 Quart | View on Amazon |
| VALVOLINE Fits: 4.4L V8 Turbocharged | 893931 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | European Vehicle Full Synthetic SAE 0W-301 Quart | View on Amazon |
This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable.
12 Oil parts are listed for the 2021 BMW X6, from LIQUI MOLY, VALVOLINE, PENTOSIN and 1 other brand. LIQUI MOLY 22044 carries the "Popular" badge. 1 part fits every engine; the other 11 are engine-specific.
Oil Cooler
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| NISSENS Fits: 3.0L L6 Turbocharged | 91359 | 🇺🇸 US 🇨🇦 CA | without Housing | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | ECK0273 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| ÜRO PARTS Fits: 3.0L L6 Turbocharged | 11428583901 | 🇺🇸 US 🇨🇦 CA | Located on oil filter housing. | View on Amazon |
| VEMO Fits: 3.0L L6 Turbocharged | V20600077 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant.
4 Oil Cooler parts are listed for the 2021 BMW X6, from NISSENS, REIN, ÜRO PARTS and 1 other brand.
Listed part numbers: NISSENS 91359, REIN ECK0273 and ÜRO PARTS 11428583901, plus the other parts above.
Oil Cooler Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 77010300 | 🇺🇸 US 🇨🇦 CA | UpperEngine # B58B30C | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 77010400 | 🇺🇸 US 🇨🇦 CA | LowerEngine # B58B30C | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 784680 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
3 Oil Cooler Gasket parts for the 2021 BMW X6 come from 2 brands — AJUSA and ELRING.
Listed part numbers: AJUSA 77010300, AJUSA 77010400 and ELRING 784680.
Oil Dipstick / Tube Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Fits: 3.0L L6 Turbocharged | 748935 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
This table covers the seals at the Oil Dipstick / Tube. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
This group shows a single part: ELRING 748935.
Oil Drain Plug
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| DORMAN Popular Fits: 3.0L L6 Turbocharged | 090088 | 🇺🇸 US 🇨🇦 CA | MetalStandard | View on Amazon |
| AGS Fits: 3.0L L6 Turbocharged | ODP00010 | 🇺🇸 US 🇨🇦 CA | M12x1.50 | View on Amazon |
| ELRING Fits: all 2021 X6 engines | 455740 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | with Seal RingBolt Head-/Nut Design: Male Hex | View on Amazon |
| ELRING Fits: all 2021 X6 engines | 427210 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | without Seal RingBolt Head-/Nut Design: Male Hex | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | HWU1041 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| REIN Fits: 4.4L V8 Turbocharged | HWU0115 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the drain plugs in the oil pan.
6 Oil Drain Plug parts are listed for the 2021 BMW X6, from ELRING, REIN, DORMAN and 1 other brand. DORMAN 090088 carries the "Popular" badge. 2 parts fit every engine; the other 4 are engine-specific.
This group includes DORMAN 090088, AGS ODP00010 and ELRING 455740 and the remaining parts above.
Oil Drain Plug Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 21010400 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30Cwith Original Equipment (OE) # 7119963132 | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 21016800 | 🇺🇸 US 🇨🇦 CA | M50i Model | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 22008600 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 110507 | 🇺🇸 US 🇨🇦 CA | Material: CopperOutside Diameter: 16.0 mm | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 247405 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Material: Aluminium | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 110906 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Material: CopperOuter Diameter [MM]: 17 | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 417005800 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
7 Oil Drain Plug Gasket parts for the 2021 BMW X6 come from 3 brands — AJUSA, ELRING and VICTOR REINZ.
Listed part numbers: AJUSA 21010400, AJUSA 21016800 and AJUSA 22008600, plus the other parts above.
Oil Filler Cap
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| MOTORAD Popular Fits: 4.4L V8 Turbocharged | MO156 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| REIN Popular Fits: 4.4L V8 Turbocharged | CPL0036 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| BECK/ARNLEY Fits: 4.4L V8 Turbocharged | 0160152 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| CALORSTAT Fits: 4.4L V8 Turbocharged | OC2314 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | PlasticTwist-On | View on Amazon |
| MOTORAD Fits: all 2021 X6 engines | MO214 | 🇺🇸 US 🇨🇦 CA | M50i Model | View on Amazon |
| ÜRO PARTS Fits: 4.4L V8 Turbocharged | 11128655331 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| VAICO Fits: all 2021 X6 engines | V204688 | 🇺🇸 US 🇨🇦 CA | M50i Model | View on Amazon |
This table covers the caps on the oil filler neck.
7 Oil Filler Cap parts are listed for the 2021 BMW X6, from MOTORAD, REIN, BECK/ARNLEY and 3 other brands. MOTORAD MO156 carries the "Popular" badge. 2 parts fit every engine; the other 5 are engine-specific.
Listed part numbers: MOTORAD MO156, REIN CPL0036 and BECK/ARNLEY 0160152, plus the other parts above.
Oil Filter
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| PRO-TEC Popular Fits: 4.4L V8 Turbocharged | PXL57189 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| CHAMP / LUBER-FINER Fits: 4.4L V8 Turbocharged | P987 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| FAMOUS BRAND Fits: 4.4L V8 Turbocharged | 84189 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| FVP Fits: 3.0L L6 Turbocharged | G0342 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| PRO-TEC Fits: 3.0L L6 Turbocharged | PXL10342 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| PUROLATOR Fits: 4.4L V8 Turbocharged | L25904 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| ULTRA-POWER Fits: 4.4L V8 Turbocharged | 57189 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Fits or OE # 11427848321 | View on Amazon |
| VARIOUS MFR Fits: 4.4L V8 Turbocharged | PO5904EX | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Extended Life | View on Amazon |
| VARIOUS MFR Fits: 4.4L V8 Turbocharged | PG5904 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
High Performance / Heavy Duty
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| MOBIL Fits: 3.0L L6 Turbocharged | M1C457A | 🇺🇸 US 🇨🇦 CA | Extended Performance | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| HENGST Popular Fits: 3.0L L6 Turbocharged | E859HD352 | 🇺🇸 US 🇨🇦 CA | Includes Gasket SetCartridge | View on Amazon |
| MAHLE / CLEVITE Popular Fits: 4.4L V8 Turbocharged | OX3537D | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Cartridge | View on Amazon |
| MANN Popular Fits: 3.0L L6 Turbocharged | HU6022Z | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| WIX Popular Fits: 4.4L V8 Turbocharged | 57189 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| BECK/ARNLEY Fits: 4.4L V8 Turbocharged | 0410872 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| FEL-PRO Fits: 4.4L V8 Turbocharged | OFCS2006 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Cap and Filter | View on Amazon |
| HASTINGS / BALDWIN Fits: 3.0L L6 Turbocharged | P40076 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| HASTINGS / BALDWIN Fits: 4.4L V8 Turbocharged | LF665 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| HENGST Fits: 4.4L V8 Turbocharged | E359HD306 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Gasket SetCartridge | View on Amazon |
| HENGST Fits: 4.4L V8 Turbocharged | E359HD801 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Gasket SetCartridge | View on Amazon |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | OX1146D | 🇺🇸 US 🇨🇦 CA | Cartridge | View on Amazon |
| MANN Fits: 4.4L V8 Turbocharged | HU8007Z | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VARIOUS MFR Fits: 3.0L L6 Turbocharged | PG99256EX | 🇺🇸 US 🇨🇦 CA | Extended Life | View on Amazon |
| WIX Fits: 3.0L L6 Turbocharged | WL10342 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.
24 Oil Filter parts are listed for the 2021 BMW X6, from VARIOUS MFR, HENGST, PRO-TEC and 12 other brands. PRO-TEC PXL57189 carries the "Popular" badge.
In the Economy grade, PRO-TEC, VARIOUS MFR, CHAMP / LUBER-FINER and 4 other brands supply 9 parts: the catalog's value-priced group. A representative part number is PRO-TEC PXL57189.
In the High Performance / Heavy Duty grade, MOBIL supplies 1 part: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is MOBIL M1C457A.
The Standard Replacement section lists 14 options from HENGST, MAHLE / CLEVITE, MANN and 5 other brands — built to original-equipment specification. HENGST E859HD352 is listed in this group.
Oil Filter Cover
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ULTRA-POWER Popular Fits: 4.4L V8 Turbocharged | 921111 | 🇺🇸 US 🇨🇦 CA | Oil Filter Cover or CapCover | View on Amazon |
| DORMAN Fits: 4.4L V8 Turbocharged | 921111 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | without Drain Plug | View on Amazon |
| MOTORAD Fits: 3.0L L6 Turbocharged | MO388 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| MOTORAD Fits: 4.4L V8 Turbocharged | MO308 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| REIN Fits: 3.0L L6 Turbocharged | CPL0070 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| REIN Fits: 4.4L V8 Turbocharged | CPL0071 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Fits M Competition or M Modelwith Oil Filter OE# 11427848321 | View on Amazon |
| SKP Fits: 4.4L V8 Turbocharged | SK121443 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | without Drain Plug | View on Amazon |
This table covers the Oil Filter covers.
7 Oil Filter Cover parts for the 2021 BMW X6 come from 5 brands — MOTORAD, REIN, ULTRA-POWER and 2 other brands. The "Popular" part is ULTRA-POWER 921111.
This group includes ULTRA-POWER 921111 and MOTORAD MO388 and the remaining parts above.
Oil Filter Housing
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| DORMAN Fits: 3.0L L6 Turbocharged | 926453 | 🇺🇸 US 🇨🇦 CA | OE FIX | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | B33500 | 🇺🇸 US 🇨🇦 CA | with Oil Cooler | View on Amazon |
| HENGST Fits: 3.0L L6 Turbocharged | H811H | 🇺🇸 US 🇨🇦 CA | with E859H D352 Filter, Oil Cooler and Bolts/Screws | View on Amazon |
| VEMO Fits: 3.0L L6 Turbocharged | V20601662 | 🇺🇸 US 🇨🇦 CA | Includes: Oil cooler, Oil filter housing, seal rings | View on Amazon |
This table covers the Oil Filter housings.
4 Oil Filter Housing parts for the 2021 BMW X6 come from 4 brands — DORMAN, ELRING, HENGST and 1 other brand.
This group includes DORMAN 926453, ELRING B33500 and HENGST H811H and the remaining parts above.
Oil Filter Housing Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Fits: 3.0L L6 Turbocharged | 784620 | 🇺🇸 US 🇨🇦 CA | Engine SidedAWD | View on Amazon |
This table covers the seals at the Oil Filter Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
One part is listed for the 2021 BMW X6 — ELRING 784620.
Oil Level Sensor
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| HELLA Popular Fits: 4.4L V8 Turbocharged | 013680141 | 🇺🇸 US | 3-Pin ConnectorIncludes Seal | View on Amazon |
| FACET Fits: 4.4L V8 Turbocharged | 70240 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| HELLA Fits: 4.4L V8 Turbocharged | 010497721 | 🇺🇸 US 🇨🇦 CA | 3-Pin ConnectorIncludes Seal | View on Amazon |
| STANDARD MOTOR PRODUCTS Fits: 4.4L V8 Turbocharged | FLS325 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ÜRO PARTS Fits: 4.4L V8 Turbocharged | 12618638754 | 🇺🇸 US 🇨🇦 CA | M50I Model12V | View on Amazon |
This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors.
5 Oil Level Sensor parts are listed for the 2021 BMW X6, from HELLA, FACET, STANDARD MOTOR PRODUCTS and 1 other brand. HELLA 013680141 carries the "Popular" badge.
This group includes HELLA 013680141, FACET 70240 and HELLA 010497721 and the remaining parts above.
Oil Level Sensor Gasket / O-Ring
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 4.4L V8 Turbocharged | 16078650 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ELRING Fits: all 2021 X6 engines | 351210 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Colour: BlackMaterial: AEM (Ethylene Acrylate Rubber) | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 078500 | 🇺🇸 US 🇨🇦 CA | Material: AEM (Ethylene Acrylate Rubber) | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 301540 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Colour: Red | View on Amazon |
This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.
4 Oil Level Sensor Gasket / O-Ring parts are listed for the 2021 BMW X6, from ELRING and AJUSA. 1 part fits every engine; the other 3 are engine-specific.
This group includes AJUSA 16078650, ELRING 351210 and ELRING 078500 and the remaining parts above.
Oil Pan
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Fits: 3.0L L6 Turbocharged | ESK0249 | 🇺🇸 US 🇨🇦 CA | Kit | View on Amazon |
This table covers the oil pans that hold the engine's oil sump.
This group shows a single part: REIN ESK0249.
Oil Pan Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 4.4L V8 Turbocharged | 691403 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | UpperM Competition | View on Amazon |
| ELRING Popular Fits: 4.4L V8 Turbocharged | 691390 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Drain Plug Gasket Included: No | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 59018100 | 🇺🇸 US 🇨🇦 CA | M50i Model | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 59019400 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Model | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 380271 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 303180 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M CompetitionBody code: F96 | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 299510 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M CompetitionBody code: F96 | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 631580 | 🇺🇸 US | LowerM Model | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 631590 | 🇺🇸 US | UpperM Model | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 703141410 | 🇺🇸 US 🇨🇦 CA | RTV Silicone | View on Amazon |
This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
10 Oil Pan Gasket parts are listed for the 2021 BMW X6, from ELRING, AJUSA and VICTOR REINZ. ELRING 691403 carries the "Popular" badge.
Oil Pump Chain
Kit
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| VAICO Popular Fits: 3.0L L6 Turbocharged | V203921 | 🇺🇸 US 🇨🇦 CA | Expert Kits +Oil Pump Drive Set | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| S.A. GEAR Fits: 3.0L L6 Turbocharged | C1213 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| S.A. GEAR Fits: 3.0L L6 Turbocharged | 76437P | 🇺🇸 US 🇨🇦 CA | Includes Chain, Oil Pump SprocketOil Pump Drive Set | View on Amazon |
| S.A. GEAR Fits: 3.0L L6 Turbocharged | C1165 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | C530 | 🇺🇸 US 🇨🇦 CA | Engine Oil Pump Chain | View on Amazon |
| VAICO Fits: 4.4L V8 Turbocharged | V203921 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Expert Kits +Oil Pump Drive Set | View on Amazon |
This table covers the chains that drive the oil pump.
6 Oil Pump Chain parts for the 2021 BMW X6 come from 3 brands — S.A. GEAR, VAICO and CLOYES. The "Popular" part is VAICO V203921.
The Kit section lists 1 option from VAICO — grouped under the catalog's "Kit" designation — the notes column spells out what sets them apart. VAICO V203921 is listed in this group.
Standard Replacement: 3 parts, from S.A. GEAR. A representative part number is S.A. GEAR C1213.
2 further parts sit outside the graded sections, with the same engine-level match.
This group includes VAICO V203921, S.A. GEAR C1213 and S.A. GEAR 76437P and the remaining parts above.
Oil Pump Sprocket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | S1172 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the Oil Pump sprockets.
This group shows a single part: CLOYES S1172.
Rocker Arm
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| INA Fits: 3.0L L6 Turbocharged | VF0241 | 🇺🇸 US 🇨🇦 CA | Intake | View on Amazon |
This table covers the rocker arms that transfer cam motion to the valves.
One part is listed for the 2021 BMW X6 — INA VF0241.
Timing Chain
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | C528 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the timing chains that keep the cams in time with the crank.
This group shows a single part: CLOYES C528.
Timing Chain & Component Kit
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| S.A. GEAR Popular Fits: 3.0L L6 Turbocharged | 76399 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | 90528SAX | 🇺🇸 US 🇨🇦 CA | Does Not Include SprocketsIncludes Timing Chain Tensioner, Chain Guide (2), Chain Tensioner Guide, Timing Chain, Oil Pump Chain | View on Amazon |
| CLOYES Fits: 3.0L L6 Turbocharged | 90528SA | 🇺🇸 US 🇨🇦 CA | Includes: Timing Chain Tensioner, Timing Chain Guide (2), Timing Chain Tensioner Guide, Timing Chain, Oil Pump Chain, Oil Pump Sprocket | View on Amazon |
| VAICO Fits: 3.0L L6 Turbocharged | V2010026BEK | 🇺🇸 US 🇨🇦 CA | Includes: Timing chains, Tensioner, Guides | View on Amazon |
| VAICO Fits: 3.0L L6 Turbocharged | V2010026 | 🇺🇸 US 🇨🇦 CA | Includes: Timing Chain, Tensioner, Guides, camshaft adjusters, bolts | View on Amazon |
This table covers kits that group a timing chain with the related tensioners and guides.
5 Timing Chain & Component Kit parts are listed for the 2021 BMW X6, from CLOYES, VAICO and S.A. GEAR. S.A. GEAR 76399 carries the "Popular" badge.
Economy: 1 part, from S.A. GEAR. A representative part number is S.A. GEAR 76399.
The Standard Replacement section: 4 options from CLOYES and VAICO. CLOYES 90528SAX is listed in this group.
Part numbers include S.A. GEAR 76399, CLOYES 90528SAX and CLOYES 90528SA, among others listed above.
Timing Chain Cover Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Fits: 4.4L V8 Turbocharged | 369814 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | LowerM Competition | View on Amazon |
This table covers the gaskets that seal the Timing Chain Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
This group shows a single part: ELRING 369814.
Timing Chain Guide / Damper
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | 96180 | 🇺🇸 US 🇨🇦 CA | Engine Timing Chain Guide | View on Amazon |
| CLOYES Fits: 3.0L L6 Turbocharged | 96181 | 🇺🇸 US 🇨🇦 CA | Engine Timing Chain Guide | View on Amazon |
| CLOYES Fits: 3.0L L6 Turbocharged | 96182 | 🇺🇸 US 🇨🇦 CA | Engine Timing Chain Tensioner Guide | View on Amazon |
This table covers the guides and dampers that keep the timing chain on its path.
3 Timing Chain Guide / Damper parts for the 2021 BMW X6 come from CLOYES.
This group includes CLOYES 96180, CLOYES 96181 and CLOYES 96182.
Timing Chain Tensioner
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | 96179 | 🇺🇸 US 🇨🇦 CA | Engine Timing Chain Tensioner | View on Amazon |
This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage.
One part is listed for the 2021 BMW X6 — CLOYES 96179.
Timing Cover Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 4.4L V8 Turbocharged | 77031300 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ELRING Fits: 4.4L V8 Turbocharged | 648850 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Cylinder Head,LeftM Competition | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 648290 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Cylinder Head,RightM Competition | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 302411 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M CompetitionBody code: F96 | View on Amazon |
This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
4 Timing Cover Gasket parts are listed for the 2021 BMW X6, from ELRING and AJUSA.
Part numbers include AJUSA 77031300, ELRING 648850 and ELRING 648290, among others listed above.
Timing Cover Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 4.4L V8 Turbocharged | TCS46311 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front | View on Amazon |
| MAHLE / CLEVITE Fits: 4.4L V8 Turbocharged | 67930 | 🇺🇸 US 🇨🇦 CA | PTFE (Polytetrafluoroethylene) | View on Amazon |
This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
2 Timing Cover Seal parts are listed for the 2021 BMW X6, from FEL-PRO and MAHLE / CLEVITE.
Part numbers include FEL-PRO TCS46311 and MAHLE / CLEVITE 67930.
Turbocharger
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| BORG-WARNER Fits: 3.0L L6 Turbocharged | 18559880115 | 🇺🇸 US 🇨🇦 CA | with OE No. 11657934386 | View on Amazon |
| GPD Fits: 3.0L L6 Turbocharged | 2512001 | 🇺🇸 US 🇨🇦 CA | with Electronic Actuator | View on Amazon |
| GPD Fits: 4.4L V8 Turbocharged | 2511766 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RightM Competition or M Model | View on Amazon |
| GPD Fits: 4.4L V8 Turbocharged | 2511767 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | LeftM Competition or M Model | View on Amazon |
This table covers the turbochargers that compress intake air.
4 Turbocharger parts are listed for the 2021 BMW X6, from GPD and BORG-WARNER.
Part numbers include BORG-WARNER 18559880115, GPD 2512001 and GPD 2511766, among others listed above.
Turbocharger Boost Sensor
Daily Driver
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| BECK/ARNLEY Fits: 4.4L V8 Turbocharged | 1580726 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| HELLA Fits: 4.4L V8 Turbocharged | 358152381 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | 4-Pin ConnectorBolted | View on Amazon |
This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors.
2 Turbocharger Boost Sensor parts for the 2021 BMW X6 come from 2 brands — BECK/ARNLEY and HELLA.
In the Daily Driver grade, BECK/ARNLEY supplies 1 part: grouped for everyday commuting duty. A representative part number is BECK/ARNLEY 1580726.
Standard Replacement: 1 part, from HELLA. A representative part number is HELLA 358152381.
Listed part numbers: BECK/ARNLEY 1580726 and HELLA 358152381.
Turbocharger Coolant Line
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Fits: 3.0L L6 Turbocharged | CHT0972 | 🇺🇸 US 🇨🇦 CA | Return | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | CHT0971 | 🇺🇸 US 🇨🇦 CA | Supply | View on Amazon |
| REIN Fits: 4.4L V8 Turbocharged | CHT0698 | 🇺🇸 US 🇨🇦 CA | Return (Turbocharger To Pipe)M50I Model | View on Amazon |
| REIN Fits: 4.4L V8 Turbocharged | CHT0697 | 🇺🇸 US 🇨🇦 CA | Supply (Turbocharger To Pipe)M50I Model | View on Amazon |
| REIN Fits: 4.4L V8 Turbocharged | CHT0695 | 🇺🇸 US 🇨🇦 CA | Supply (Turbocharger To Pipe)M50I Model | View on Amazon |
This table covers the Turbocharger Coolant lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early.
REIN supplies the 5 Turbocharger Coolant Line parts for the 2021 BMW X6.
This group includes REIN CHT0972, REIN CHT0971 and REIN CHT0698 and the remaining parts above.
Turbocharger Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 3.0L L6 Turbocharged | 087320 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 01158200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Exhaust | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | JTC12221 | 🇺🇸 US 🇨🇦 CA | Mounting Gasket Set | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | JTC12319 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Mounting Gasket Set | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 344890 | 🇺🇸 US 🇨🇦 CA | Inner Diameter [MM]: 37,5Material: FPM (fluoride rubber) | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 720580 | 🇺🇸 US 🇨🇦 CA | Inner Diameter [MM]: 68Material: FPM (fluoride rubber) | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 113510 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 233880 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M CompetitionBody code: F96 | View on Amazon |
| GPD Fits: 3.0L L6 Turbocharged | 2535112 | 🇺🇸 US 🇨🇦 CA | Only Fits Compatible Aftermarket Turbochargers | View on Amazon |
This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
9 Turbocharger Gasket parts for the 2021 BMW X6 come from 3 brands — ELRING, AJUSA and GPD. The "Popular" part is ELRING 087320.
Listed part numbers: ELRING 087320, AJUSA 01158200 and AJUSA JTC12221, plus the other parts above.
Turbocharger Inlet Hose Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Fits: 3.0L L6 Turbocharged | 113670 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
This table covers the gaskets that seal the Turbocharger Inlet Hose. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
One part is listed for the 2021 BMW X6 — ELRING 113670.
Turbocharger Mounting Hardware
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Fits: 3.0L L6 Turbocharged | 114510 | 🇺🇸 US 🇨🇦 CA | with gaskets/sealswith Bolts/Screws | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | TRK0024 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the fasteners that mount the turbocharger.
2 Turbocharger Mounting Hardware parts for the 2021 BMW X6 come from 2 brands — ELRING and REIN.
Part numbers include ELRING 114510 and REIN TRK0024.
Turbocharger Oil Line
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Popular Fits: 4.4L V8 Turbocharged | TFP0346 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M ModelFor Cyl. 5-8 | View on Amazon |
| REIN Popular Fits: 4.4L V8 Turbocharged | TFP0345 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | For Cyl. 1-4Supply Line | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | OP11237 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30CSupply Tube | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | OP11014 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M Competition or M Modelfor Cylinders 5 To 8 Only | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | OP11235 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | for Cylinders 1 To 4 OnlySupply Tube | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | OP11307 | 🇺🇸 US 🇨🇦 CA | M50I Modelfor Cylinders 5 To 8 Only | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | TFP0393 | 🇺🇸 US 🇨🇦 CA | Supply Line | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | TRP0391 | 🇺🇸 US 🇨🇦 CA | Return Line | View on Amazon |
| VAICO Fits: 4.4L V8 Turbocharged | V204576 | 🇺🇸 US 🇨🇦 CA | M Model or M50i ModelFeed Line | View on Amazon |
This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early.
9 Turbocharger Oil Line parts are listed for the 2021 BMW X6, from REIN, AJUSA and VAICO. REIN TFP0346 carries the "Popular" badge.
This group includes REIN TFP0346, REIN TFP0345 and AJUSA OP11237 and the remaining parts above.
Turbocharger Oil Line Gasket / O-Ring
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 16007800 | 🇺🇸 US 🇨🇦 CA | Turbocharger Coolant Line O-Ring | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 876070 | 🇺🇸 US 🇨🇦 CA | AWDBody code: G06 | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 202790 | 🇺🇸 US 🇨🇦 CA | Inner Diameter [MM]: 9.5Material: FPM (fluoride rubber) | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 239251 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M CompetitionBody code: F96 | View on Amazon |
This table covers the Turbocharger Oil Line Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.
4 Turbocharger Oil Line Gasket / O-Ring parts are listed for the 2021 BMW X6, from ELRING and AJUSA.
This group includes AJUSA 16007800, ELRING 876070 and ELRING 202790 and the remaining parts above.
Valve Cover
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| SKP Fits: all 2021 X6 engines | SK743462 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VAICO Fits: 3.0L L6 Turbocharged | V205366 | 🇺🇸 US 🇨🇦 CA | Plastic | View on Amazon |
This table covers the Valve covers.
2 Valve Cover parts for the 2021 BMW X6 come from 2 brands — SKP and VAICO. 1 part fits every engine; the other 1 is engine-specific.
This group includes SKP SK743462 and VAICO V205366.
Valve Cover Bolt / Screw
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ÜRO PARTS Fits: 3.0L L6 Turbocharged | 11129454322 | 🇺🇸 US 🇨🇦 CA | 6x30.0mm Torx Head | View on Amazon |
This table covers the Valve Cover Bolt screws. Typical signs include a rounded head, a seeping bleeder, or a fastener that will not hold torque. Do not force a new screw into a stripped hole — repair the thread first.
This group shows a single part: ÜRO PARTS 11129454322.
Valve Cover Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 56080600 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 56081400 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | LeftFor Cylinders 5 to 8 Only | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 56081500 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RightFor Cylinders 1 to 4 Only | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 811530 | 🇺🇸 US 🇨🇦 CA | Material: Zinc-Copper brazing alloy (ZN-CU) | View on Amazon |
| ELRING Fits: 3.0L L6 Turbocharged | 091010 | 🇺🇸 US 🇨🇦 CA | Material: DI HT | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 795130 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RightM Competition | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 795120 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | LeftM Competition | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 151120501 | 🇺🇸 US 🇨🇦 CA | Set | View on Amazon |
This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
8 Valve Cover Gasket parts are listed for the 2021 BMW X6, from ELRING, AJUSA and VICTOR REINZ.
Listed part numbers: AJUSA 56080600, AJUSA 56081400 and AJUSA 56081500, plus the other parts above.
Valve Lifter
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: all 2021 X6 engines | 85022300 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
This table covers the lifters / tappets that transfer cam motion to the valves.
One part is listed for the 2021 BMW X6 — AJUSA 85022300.
Valve Stem Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 3.0L L6 Turbocharged | 364500 | 🇺🇸 US 🇨🇦 CA | SetMaterial: FPM (fluoride rubber) | View on Amazon |
| ELRING Popular Fits: 3.0L L6 Turbocharged | 660360 | 🇺🇸 US 🇨🇦 CA | SetMaterial: FPM (fluoride rubber) | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 57051500 | 🇺🇸 US 🇨🇦 CA | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 12033700 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| AJUSA Fits: 4.4L V8 Turbocharged | 57069600 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ELRING Fits: 3.0L L6 Turbocharged | 584820 | 🇺🇸 US 🇨🇦 CA | Set | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 198770 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Height [MM]: 16Outer Diameter [MM]: 23 | View on Amazon |
| ELRING Fits: 4.4L V8 Turbocharged | 199440 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | SetMaterial: FPM (fluoride rubber) | View on Amazon |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | SS46008 | 🇺🇸 US 🇨🇦 CA | SetMetal with Molded Rubber | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 123686601 | 🇺🇸 US 🇨🇦 CA | SetContains 12 Pieces | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 123725601 | 🇺🇸 US 🇨🇦 CA | SetContains 12 Pieces | View on Amazon |
This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
11 Valve Stem Seal parts are listed for the 2021 BMW X6, from ELRING, AJUSA, VICTOR REINZ and 1 other brand. ELRING 364500 carries the "Popular" badge.
Variable Valve Timing (VVT) Eccentric Shaft Actuator
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ÜRO PARTS Fits: 4.4L V8 Turbocharged | 11378652738 | 🇺🇸 US 🇨🇦 CA | M50I Modelfor Valvetronic System | View on Amazon |
This table covers the Variable Valve Timing (VVT) Eccentric Shaft actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same.
One part is listed for the 2021 BMW X6 — ÜRO PARTS 11378652738.
Variable Valve Timing (VVT) Solenoid / Actuator
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| GATES Popular Fits: 4.4L V8 Turbocharged | VVS229 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| HOLSTEIN Fits: 4.4L V8 Turbocharged | 2VTS0370 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Adjuster Magnet | View on Amazon |
| VAICO Fits: 4.4L V8 Turbocharged | V204822 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| VEMO Fits: 4.4L V8 Turbocharged | V20540005 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| VAICO Fits: 4.4L V8 Turbocharged | V203994 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| GATES Popular Fits: 3.0L L6 Turbocharged | VVS229 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| HOLSTEIN Fits: 3.0L L6 Turbocharged | 2VTS0370 | 🇺🇸 US 🇨🇦 CA | Adjuster Magnet | View on Amazon |
| VEMO Fits: 3.0L L6 Turbocharged | V20540005 | 🇺🇸 US 🇨🇦 CA | Oil Control | View on Amazon |
| WELLS Fits: 3.0L L6 Turbocharged | 2T1286 | 🇺🇸 US 🇨🇦 CA | Adjuster Magnet | View on Amazon |
| WELLS Fits: 3.0L L6 Turbocharged | 2T1249 | 🇺🇸 US 🇨🇦 CA | View on Amazon |
This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same.
10 Variable Valve Timing (VVT) Solenoid / Actuator parts are listed for the 2021 BMW X6, from GATES, HOLSTEIN, VAICO and 2 other brands. GATES VVS229 carries the "Popular" badge.
Economy: 4 parts, from GATES, HOLSTEIN, VAICO and 1 other brand. A representative part number is GATES VVS229.
The Standard Replacement section: 1 option from VAICO. VAICO V203994 is listed in this group.
5 ungrouped parts are not assigned to a grade, with the same engine-level match.
Variable Valve Timing (VVT) Solenoid Gasket / Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: all 2021 X6 engines | 01907000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
This group shows a single part: AJUSA 01907000.
Buying Engine Parts for a 2021 BMW X6
On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.
- Match the engine first. Some engine parts fit every engine; others are engine-specific. Each row shows which engine(s) it fits.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Oil Filter and Crankshaft Seal .
Frequently Asked Questions
How many engine parts fit the 2021 BMW X6?
Our catalog currently lists 261 engine parts for the 2021 BMW X6 across 54 subcategories and 48 brands, covering both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. Each part is matched to the engine(s) it fits.
Do engine parts differ between 2021 BMW X6 engines?
Some do. 13 parts fit every engine; the other 248 are engine-specific. Each row (and the filter at the top) shows which. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.
What are the signs of engine problems on a 2021 BMW X6?
Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What oil viscosity is listed for the 2021 BMW X6?
Oil rows on this page include SAE 0W-20, SAE 0W-30 and SAE 5W-30. Confirm the engine and the weight on the filler cap before you buy — high-mileage and standard fills can differ.
What should I replace at the same time?
Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2021 BMW X6 was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 2021 BMW X6?
First match the engine — each row shows which engine(s) the part fits. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 2021 BMW X6
Engine Parts for Other BMW X6 Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.