2025 BMW X6 Engine Parts

Engine:

Showing parts for every engine. Select an engine to see only what fits.

This page lists 53 engine parts for the 2025 BMW X6, across 17 part types, covering both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. Every part shows its brand, manufacturer part number and fitment notes.

On the 2025 BMW X6, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. 32 parts of the 53 listed are Oil Filter (18 parts), Oil (9 parts) and Variable Valve Timing (VVT) Solenoid / Actuator (5 parts). The other 14 part types cover the remaining 21 parts.

Harmonic Balancer Bolt

Brand Part Number Markets Notes Buy
REIN Fits: 3.0L L6 Turbocharged HWB0074
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
10 x 65mm
View on
Amazon

This table covers the Harmonic Balancer bolts.

Intake Manifold Gasket

Brand Part Number Markets Notes Buy
ELRING Fits: 3.0L L6 Turbocharged B26210
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Material: FPM (Fluoride Rubber)
View on
Amazon

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Motor Mount

Brand Part Number Markets Notes Buy
ANCHOR Fits: 3.0L L6 Turbocharged 10258
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front RightHydraulic
View on
Amazon
ANCHOR Fits: 3.0L L6 Turbocharged 10260
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front LeftHydraulic
View on
Amazon
DEA / MARMON RIDE CONTROL Fits: 3.0L L6 Turbocharged A70079
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Left
View on
Amazon
DEA / MARMON RIDE CONTROL Fits: 3.0L L6 Turbocharged A70084
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Right
View on
Amazon

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes.

Oil

Summary: Notes list SAE 0W-20, SAE 0W-30 and SAE 5W-30. Confirm the engine and the weight on the filler cap before you buy. Replacement brands in this table include LIQUI MOLY and VALVOLINE.

Brand Part Number Markets Notes Buy
LIQUI MOLY Popular Fits: 3.0L L6 Turbocharged 22046
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Top Tec 6600 0W-205 Liter
View on
Amazon
VALVOLINE Popular Fits: 4.4L V8 Turbocharged 787301
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
European Vehicle Full Synthetic SAE 5W-301 Quart
View on
Amazon
LIQUI MOLY Fits: 3.0L L6 Turbocharged 22044
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Top Tec 6600 0W-201 Liter
View on
Amazon
LIQUI MOLY Fits: 3.0L L6 Turbocharged 22048
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Top Tec 6600 0W-2020 Liter
View on
Amazon
LIQUI MOLY Fits: 4.4L V8 Turbocharged 22260
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Special Tec B FE 0W-301 Liter
View on
Amazon
LIQUI MOLY Fits: 4.4L V8 Turbocharged 22261
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Special Tec B FE 0W-305 Liter
View on
Amazon
LIQUI MOLY Fits: 4.4L V8 Turbocharged 22269
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Special Tec B FE 0W-3020 Liter
View on
Amazon
VALVOLINE Fits: 3.0L L6 Turbocharged 888048
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
European Vehicle Full Synthetic SAE 0W-201 Quart
View on
Amazon
VALVOLINE Fits: all 2025 X6 engines 893931
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
European Vehicle Full Synthetic SAE 0W-301 Quart
View on
Amazon

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable.

Oil Drain Plug

Brand Part Number Markets Notes Buy
DORMAN Fits: 3.0L L6 Turbocharged 090088
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
MetalStandard
Fitment notes — DORMAN 090088
MetalStandardThread SizeM12-1.50Under-Head Length: 16.95mmHead Size: 17mmHead Style: Hex
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged HWU1041
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the drain plugs in the oil pan.

Oil Filler Cap

Brand Part Number Markets Notes Buy
MOTORAD Fits: all 2025 X6 engines MO214
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the caps on the oil filler neck.

Oil Filter

Economy

Brand Part Number Markets Notes Buy
PRO-TEC Popular Fits: 4.4L V8 Turbocharged PXL57189
🇺🇸 US 🇨🇦 CA
View on
Amazon
CHAMP / LUBER-FINER Fits: 4.4L V8 Turbocharged P987
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
M Competition
View on
Amazon
FAMOUS BRAND Fits: 4.4L V8 Turbocharged 84189
🇺🇸 US 🇨🇦 CA
View on
Amazon
FVP Fits: 3.0L L6 Turbocharged G0342
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
PRO-TEC Fits: 3.0L L6 Turbocharged PXL10342
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
PUROLATOR Fits: 4.4L V8 Turbocharged L25904
🇺🇸 US 🇨🇦 CA
View on
Amazon
ULTRA-POWER Fits: 4.4L V8 Turbocharged 57189
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Fits OE # 11427848321
Fitment notes — ULTRA-POWER 57189
Fits:
OE # 11427848321
or:
OE # 11-42 7 583 220
View on
Amazon
VARIOUS MFR Fits: 4.4L V8 Turbocharged PO5904EX
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Extended Life
View on
Amazon
VARIOUS MFR Fits: 4.4L V8 Turbocharged PG5904
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

High Performance / Heavy Duty

Brand Part Number Markets Notes Buy
MOBIL Fits: 3.0L L6 Turbocharged M1C457A
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Extended Performance
View on
Amazon

Standard Replacement

Brand Part Number Markets Notes Buy
HENGST Popular Fits: 3.0L L6 Turbocharged E859HD352
🇺🇸 US 🇨🇦 CA
Includes Gasket SetCartridge
View on
Amazon
MANN Popular Fits: 3.0L L6 Turbocharged HU6022Z
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
WIX Popular Fits: 4.4L V8 Turbocharged 57189
🇺🇸 US 🇨🇦 CA
View on
Amazon
HASTINGS / BALDWIN Fits: 3.0L L6 Turbocharged P40076
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Element
View on
Amazon
HASTINGS / BALDWIN Fits: 4.4L V8 Turbocharged LF665
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
MILD Hybrid EV-GAS MHEVElement
View on
Amazon
MANN Fits: 4.4L V8 Turbocharged HU8007Z
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
VARIOUS MFR Fits: 3.0L L6 Turbocharged PG99256EX
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Extended Life
View on
Amazon
WIX Fits: 3.0L L6 Turbocharged WL10342
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.

Oil Filter Cover

Brand Part Number Markets Notes Buy
MOTORAD Fits: 3.0L L6 Turbocharged MO388
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged CPL0070
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the Oil Filter covers.

Oil Filter Housing

Brand Part Number Markets Notes Buy
DORMAN Fits: 3.0L L6 Turbocharged 926453
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
OE FIX
View on
Amazon

This table covers the Oil Filter housings.

Oil Level Sensor Gasket / O-Ring

Brand Part Number Markets Notes Buy
AJUSA Fits: 4.4L V8 Turbocharged 16078650
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.

Timing Cover Seal

Brand Part Number Markets Notes Buy
FEL-PRO Fits: 4.4L V8 Turbocharged TCS46311
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front
View on
Amazon
MAHLE / CLEVITE Fits: 4.4L V8 Turbocharged 67930
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
PTFE (Polytetrafluoroethylene)
Fitment notes — MAHLE / CLEVITE 67930
PTFE (Polytetrafluoroethylene)
MILD HYBRID EV-GAS (MHEV)
View on
Amazon

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Turbocharger Boost Sensor

Daily Driver

Brand Part Number Markets Notes Buy
BECK/ARNLEY Fits: 4.4L V8 Turbocharged 1580726
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

Economy

Brand Part Number Markets Notes Buy
WELLS Fits: 4.4L V8 Turbocharged 5S13286
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors.

Turbocharger Gasket

Brand Part Number Markets Notes Buy
AJUSA Fits: 4.4L V8 Turbocharged 01158200
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Exhaust
View on
Amazon

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Valve Cover

Brand Part Number Markets Notes Buy
SKP Fits: all 2025 X6 engines SK743462
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the Valve covers.

Valve Stem Seal

Brand Part Number Markets Notes Buy
MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged SS46008
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
SetMetal with Molded Rubber
Fitment notes — MAHLE / CLEVITE SS46008
SetMetal with Molded Rubber
Exhaust6mm Shaft Diameter
View on
Amazon

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Variable Valve Timing (VVT) Solenoid / Actuator

Brand Part Number Markets Notes Buy
WELLS Popular Fits: 4.4L V8 Turbocharged 2T1247
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Oil Control
View on
Amazon
VNE Fits: all 2025 X6 engines 4022005
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Oil Pump Control Valve
View on
Amazon
VNE Fits: 4.4L V8 Turbocharged 4022002
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Actuator
View on
Amazon
WELLS Fits: all 2025 X6 engines 2T1249
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
WELLS Fits: 4.4L V8 Turbocharged 2T1286
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Adjuster Magnet
View on
Amazon

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same.

Variable Valve Timing (VVT) Solenoid Gasket / Seal

Brand Part Number Markets Notes Buy
AJUSA Fits: 4.4L V8 Turbocharged 01907000
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Buying Engine Parts for a 2025 BMW X6

On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.

  • Match the engine first. Some engine parts fit every engine; others are engine-specific. Each row shows which engine(s) it fits.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Oil Filter and Oil .

Frequently Asked Questions

How many engine parts fit the 2025 BMW X6?

Our catalog currently lists 53 engine parts for the 2025 BMW X6 across 17 subcategories and 27 brands, covering both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. Each part is matched to the engine(s) it fits.

Do engine parts differ between 2025 BMW X6 engines?

Some do. 5 parts fit every engine; the other 48 are engine-specific. Each row (and the filter at the top) shows which. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.

What are the signs of engine problems on a 2025 BMW X6?

Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What oil viscosity is listed for the 2025 BMW X6?

Oil rows on this page include SAE 0W-20, SAE 0W-30 and SAE 5W-30. Confirm the engine and the weight on the filler cap before you buy — high-mileage and standard fills can differ.

What should I replace at the same time?

Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2025 BMW X6 was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 2025 BMW X6?

First match the engine — each row shows which engine(s) the part fits. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 2025 BMW X6

Engine Parts for Other BMW X6 Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.