2023 BMW Z4 Engine Parts

Engine:

Showing parts for every engine. Select an engine to see only what fits.

97 Engine parts are listed for the 2023 BMW Z4, in 35 part types, covering both the 2.0L L4 Turbocharged and the 3.0L L6 Turbocharged. Each one has a brand, a manufacturer part number and notes that say where it fits.

The engine on the 2023 BMW Z4 covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. The largest groups are Oil Filter (9 parts), Motor Mount (7 parts) and Oil (7 parts). The other 32 part types cover the remaining 74 parts.

Conversion / Lower Gasket Set

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 54302500
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 113340
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with Crankshaft Seal, Oil Sump Gasket
View on
Amazon

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.

Crankshaft Seal

Brand Part Number Markets Notes Buy
ELRING Popular Fits: 3.0L L6 Turbocharged 575970
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Height [MM]: 8Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)
Fitment notes — ELRING 575970
Height [MM]: 8Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)Radial Shaft Seal Design: ASWFront
View on
Amazon
ELRING Popular Fits: 3.0L L6 Turbocharged 586550
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with Mounting SleeveMaterial: PTFE (polytetrafluoroethylene)
Fitment notes — ELRING 586550
with Mounting SleeveMaterial: PTFE (polytetrafluoroethylene)
RearTransmission Side
View on
Amazon
AJUSA Fits: 3.0L L6 Turbocharged 15075200
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
FrontClockwise
View on
Amazon
AJUSA Fits: 3.0L L6 Turbocharged 15107900
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
RearCounter Clockwise
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 813700200
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 811044800
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Rear
View on
Amazon

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Cylinder Head Bolt

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 81069200
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 794480
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
SetBolt Head-/Nut Design: Female Torx
Fitment notes — ELRING 794480
SetBolt Head-/Nut Design: Female TorxNumber of Bolts/Screws: 14Thread Size: M11X1,5x188
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 141226103
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Set
View on
Amazon

This table covers the bolts that clamp the cylinder head to the block.

Cylinder Head Gasket

Brand Part Number Markets Notes Buy
ELRING Popular Fits: 3.0L L6 Turbocharged 793491
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Installed Thickness [MM]: 0,81Material: Multi-Layer Steel (MLS)
View on
Amazon
ELRING Popular Fits: 3.0L L6 Turbocharged 739501
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Installed Thickness [MM]: 1,11Material: Multi-Layer Steel (MLS)
View on
Amazon
AJUSA Fits: 3.0L L6 Turbocharged 10248900
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Multi Layered Steel
Fitment notes — AJUSA 10248900
Multi Layered Steel
83 Bore Diameter
View on
Amazon
AJUSA Fits: 3.0L L6 Turbocharged 10248910
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Multi Layered Steel
Fitment notes — AJUSA 10248910
Multi Layered Steel
83 Bore Diameter(+0.30) Thickness
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 611084400
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
0.80mm Thickwith Engine Code B58B30B
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 611084410
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
1.10mm Thickwith Engine Code B58B30B
View on
Amazon

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Cylinder Head Gasket Set

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 52635900
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.

Engine Kit Gasket Set

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 50565600
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.

Harmonic Balancer Bolt

Brand Part Number Markets Notes Buy
REIN Fits: 3.0L L6 Turbocharged HWB0074
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
10 x 65mm
View on
Amazon

This table covers the Harmonic Balancer bolts.

Intake Manifold Gasket

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 13313000
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 711737500
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Motor Mount

Brand Part Number Markets Notes Buy
ANCHOR Popular Fits: 3.0L L6 Turbocharged 10258
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front RightHydraulic
View on
Amazon
ANCHOR Popular Fits: 3.0L L6 Turbocharged 10259
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front LeftHydraulic
View on
Amazon
DEA / MARMON RIDE CONTROL Fits: 3.0L L6 Turbocharged A70098
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Left
View on
Amazon
PIONEER Fits: 3.0L L6 Turbocharged 610258
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front Right
View on
Amazon
PIONEER Fits: 3.0L L6 Turbocharged 610259
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Front Left
View on
Amazon
WESTAR Fits: 3.0L L6 Turbocharged EM7559
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Left
View on
Amazon
WESTAR Fits: 3.0L L6 Turbocharged EM7560
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Right
View on
Amazon

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes.

Motor Mount Kit

Brand Part Number Markets Notes Buy
ANCHOR Fits: 3.0L L6 Turbocharged 300956
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the Motor Mount kits.

Oil

Summary: Notes list SAE 0W-20. Confirm the engine and the weight on the filler cap before you buy. Replacement brands in this table include LIQUI MOLY, PENTOSIN and MOBIL.

Brand Part Number Markets Notes Buy
LIQUI MOLY Popular Fits: 3.0L L6 Turbocharged 22044
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Top Tec 6600 0W-201 Liter
View on
Amazon
LIQUI MOLY Popular Fits: 3.0L L6 Turbocharged 22046
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Top Tec 6600 0W-205 Liter
View on
Amazon
LIQUI MOLY Fits: 3.0L L6 Turbocharged 22048
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Top Tec 6600 0W-2020 Liter
View on
Amazon
MOBIL Fits: 3.0L L6 Turbocharged 127568
🇺🇸 US
ESP 5W30 1 Quart
View on
Amazon
PENTOSIN Fits: 3.0L L6 Turbocharged 8044317
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Pento Speed FESAE 0W-20
Fitment notes — PENTOSIN 8044317
Pento Speed FESAE 0W-201 Liter
View on
Amazon
PENTOSIN Fits: 3.0L L6 Turbocharged 8044319
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Pento Speed FESAE 0W-20
Fitment notes — PENTOSIN 8044319
Pento Speed FESAE 0W-205 Liters
View on
Amazon
VALVOLINE Fits: 3.0L L6 Turbocharged 888048
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
European Vehicle Full Synthetic SAE 0W-201 Quart
View on
Amazon

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable.

Oil Cooler

Brand Part Number Markets Notes Buy
NISSENS Fits: 3.0L L6 Turbocharged 91359
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
without Housing
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged ECK0273
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant.

Oil Cooler Gasket

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 77010300
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Upper
View on
Amazon
AJUSA Fits: 3.0L L6 Turbocharged 77010400
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Lower
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 784680
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Oil Drain Plug

Brand Part Number Markets Notes Buy
DORMAN Fits: 3.0L L6 Turbocharged 090088
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
MetalStandard
Fitment notes — DORMAN 090088
MetalStandardThread SizeM12-1.50Under-Head Length: 16.95mmHead Size: 17mmHead Style: Hex
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 455740
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with Seal RingBolt Head-/Nut Design: Male Hex
Fitment notes — ELRING 455740
with Seal RingBolt Head-/Nut Design: Male HexThread Size: M12X1,5x16
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 427210
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
without Seal RingBolt Head-/Nut Design: Male Hex
Fitment notes — ELRING 427210
without Seal RingBolt Head-/Nut Design: Male HexThread Size: M12X1,5x16
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged HWU1041
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the drain plugs in the oil pan.

Oil Drain Plug Gasket

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 21010400
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with Original Equipment (OE) # 7119963132
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 110507
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Material: CopperOutside Diameter: 16.0 mm
View on
Amazon

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Oil Filler Cap

Brand Part Number Markets Notes Buy
MOTORAD Fits: 3.0L L6 Turbocharged MO214
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the caps on the oil filler neck.

Oil Filter

Economy

Brand Part Number Markets Notes Buy
FVP Fits: 3.0L L6 Turbocharged G0342
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
PRO-TEC Fits: 3.0L L6 Turbocharged PXL10342
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

High Performance / Heavy Duty

Brand Part Number Markets Notes Buy
MOBIL Fits: 3.0L L6 Turbocharged M1C457A
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Extended Performance
View on
Amazon

Standard Replacement

Brand Part Number Markets Notes Buy
HENGST Popular Fits: 3.0L L6 Turbocharged E859HD352
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Includes Gasket SetCartridge
View on
Amazon
MANN Popular Fits: 3.0L L6 Turbocharged HU6022Z
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
HASTINGS / BALDWIN Fits: 3.0L L6 Turbocharged P40076
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
M40I
View on
Amazon
MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged OX1146D
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Cartridge
View on
Amazon
VARIOUS MFR Fits: 3.0L L6 Turbocharged PG99256EX
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Extended Life
View on
Amazon
WIX Fits: 3.0L L6 Turbocharged WL10342
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.

Oil Filter Cover

Brand Part Number Markets Notes Buy
MOTORAD Fits: 3.0L L6 Turbocharged MO388
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged CPL0070
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the Oil Filter covers.

Oil Filter Housing

Brand Part Number Markets Notes Buy
DORMAN Fits: 3.0L L6 Turbocharged 926453
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
OE FIX
View on
Amazon
HENGST Fits: 3.0L L6 Turbocharged H811H
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with E859H D352 Filter, Oil Cooler and Bolts/Screws
View on
Amazon

This table covers the Oil Filter housings.

Oil Filter Housing Seal

Brand Part Number Markets Notes Buy
ELRING Fits: 3.0L L6 Turbocharged 784620
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Engine Side
View on
Amazon

This table covers the seals at the Oil Filter Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Oil Level Sensor Gasket / O-Ring

Brand Part Number Markets Notes Buy
ELRING Fits: 3.0L L6 Turbocharged 351210
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Colour: BlackMaterial: AEM (Ethylene Acrylate Rubber)
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 078500
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Material: AEM (Ethylene Acrylate Rubber)
View on
Amazon

This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.

Oil Pan

Brand Part Number Markets Notes Buy
REIN Fits: 3.0L L6 Turbocharged ESK0247
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Kit
View on
Amazon

This table covers the oil pans that hold the engine's oil sump.

Oil Pan Gasket

Brand Part Number Markets Notes Buy
VICTOR REINZ Fits: 3.0L L6 Turbocharged 703141410
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
RTV Silicone
View on
Amazon

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Turbocharger

Brand Part Number Markets Notes Buy
BORG-WARNER Fits: 3.0L L6 Turbocharged 18559880116
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with OE No. 11657934387
View on
Amazon

This table covers the turbochargers that compress intake air.

Turbocharger Coolant Line

Brand Part Number Markets Notes Buy
REIN Fits: 3.0L L6 Turbocharged CHT0972
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Return
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged CHT0971
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Supply
View on
Amazon

This table covers the Turbocharger Coolant lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early.

Turbocharger Gasket

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged JTC12750
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Mounting Gasket Set
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 113510
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 074140
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Suction PipeInlet Gasket
View on
Amazon

This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Turbocharger Inlet Hose Gasket

Brand Part Number Markets Notes Buy
ELRING Fits: 3.0L L6 Turbocharged 113670
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the gaskets that seal the Turbocharger Inlet Hose. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Turbocharger Mounting Hardware

Brand Part Number Markets Notes Buy
ELRING Fits: 3.0L L6 Turbocharged 113440
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
with gaskets/sealswith Bolts/Screws
View on
Amazon

This table covers the fasteners that mount the turbocharger.

Turbocharger Oil Line

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged OP11237
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Supply tube
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged TFP0393
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Supply Line
View on
Amazon
REIN Fits: 3.0L L6 Turbocharged TRP0391
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Return Line
View on
Amazon

This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early.

Valve Cover

Brand Part Number Markets Notes Buy
SKP Fits: 3.0L L6 Turbocharged SK743462
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
ÜRO PARTS Fits: 3.0L L6 Turbocharged 11128691779
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Includes Valve Cover Gasket Set
View on
Amazon
VAICO Fits: 3.0L L6 Turbocharged V204929
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Description: with valve cover gasket
View on
Amazon

This table covers the Valve covers.

Valve Cover Gasket

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 56080600
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
ELRING Fits: 3.0L L6 Turbocharged 091010
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Material: DI HT
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 151120501
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Set
Fitment notes — VICTOR REINZ 151120501
Set
with Engine Code B58B30B
View on
Amazon

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.

Valve Lifter

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 85022300
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the lifters / tappets that transfer cam motion to the valves.

Valve Stem Seal

Brand Part Number Markets Notes Buy
ELRING Popular Fits: 3.0L L6 Turbocharged 364500
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
SetMaterial: FPM (fluoride rubber)
Fitment notes — ELRING 364500
SetMaterial: FPM (fluoride rubber)Valve Stem Diameter [MM]: 5
Valve type: For inlet valves
View on
Amazon
ELRING Popular Fits: 3.0L L6 Turbocharged 660360
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
SetMaterial: FPM (fluoride rubber)
Fitment notes — ELRING 660360
SetMaterial: FPM (fluoride rubber)Valve Stem Diameter [MM]: 6
Valve type: for exhaust valves
View on
Amazon
AJUSA Fits: 3.0L L6 Turbocharged 57051500
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged SS46008
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
SetMetal with Molded Rubber
Fitment notes — MAHLE / CLEVITE SS46008
SetMetal with Molded Rubber
Exhaust6mm Shaft Diameter
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 123686603
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
SetContains 8 Pieces
Fitment notes — VICTOR REINZ 123686603
SetContains 8 Pieces
Intake
View on
Amazon
VICTOR REINZ Fits: 3.0L L6 Turbocharged 123725601
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
SetContains 12 Pieces
Fitment notes — VICTOR REINZ 123725601
SetContains 12 Pieces
Exhaust
View on
Amazon

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Variable Valve Timing (VVT) Solenoid / Actuator

Brand Part Number Markets Notes Buy
GATES Popular Fits: 3.0L L6 Turbocharged VVS229
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon
HOLSTEIN Fits: 3.0L L6 Turbocharged 2VTS0370
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Adjuster Magnet
View on
Amazon
VEMO Fits: 3.0L L6 Turbocharged V20540005
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Oil Control
View on
Amazon
WELLS Fits: 3.0L L6 Turbocharged 2T1286
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
Adjuster Magnet
View on
Amazon
WELLS Fits: 3.0L L6 Turbocharged 2T1249
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same.

Variable Valve Timing (VVT) Solenoid Gasket / Seal

Brand Part Number Markets Notes Buy
AJUSA Fits: 3.0L L6 Turbocharged 01907000
🇺🇸 US 🇨🇦 CA 🇲🇽 MX
View on
Amazon

This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.

Buying Engine Parts for a 2023 BMW Z4

On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.

  • Match the engine first. Every engine part here is engine-specific; each row shows which engine(s) it fits.
  • Read the notes on each row for position, trim and spec qualifiers before you order.
  • Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
  • Cross-reference the manufacturer part number against your old part or a service-manual listing.

Start with the largest groups on this page: Oil Filter and Motor Mount .

Frequently Asked Questions

How many engine parts fit the 2023 BMW Z4?

Our catalog currently lists 97 engine parts for the 2023 BMW Z4 across 35 subcategories and 31 brands, covering both the 2.0L L4 Turbocharged and the 3.0L L6 Turbocharged. Each part is matched to the engine(s) it fits.

Do engine parts differ between 2023 BMW Z4 engines?

Yes. Every engine part on this page is engine-specific. Each row shows which engine(s) it fits — use the filter at the top to hide the rest. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.

What are the signs of engine problems on a 2023 BMW Z4?

Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.

What oil viscosity is listed for the 2023 BMW Z4?

Oil rows on this page include SAE 0W-20. Confirm the engine and the weight on the filler cap before you buy — high-mileage and standard fills can differ.

What should I replace at the same time?

Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.

What do the market flags (US, CA, MX) on each part mean?

They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2023 BMW Z4 was originally sold in the US, the safest choice is a part marked for the US market.

How do I make sure a part fits my 2023 BMW Z4?

First match the engine — each row shows which engine(s) the part fits. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.

Other Parts for the 2023 BMW Z4

Engine Parts for Other BMW Z4 Years

Switch vehicle or jump to a subcategory

Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.