2008 Chrysler Crossfire Engine Parts

This table covers the camshafts that open the valves. Read more

MOPAR supplies both parts for the 2008 Chrysler Crossfire.

This group includes MOPAR 5097134AA and MOPAR 5097135AA.

This table covers the connecting rods between each piston and the crankshaft. Read more

One part is listed for the 2008 Chrysler Crossfire — MOPAR 5096538AA.

This table covers the Connecting Rod bolts. Read more

This group shows a single part: MOPAR 5073698AA.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Conversion / Lower Gasket Set parts are listed for the 2008 Chrysler Crossfire, from ELRING, APEX, FEL-PRO and 2 other brands. ELRING 137130 carries the "Popular" badge.

Listed part numbers: ELRING 137130, APEX ACS9014 and FEL-PRO CS26433, plus the other parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: MOPAR 5102911AA.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

4 Crankshaft Repair Sleeve parts for the 2008 Chrysler Crossfire come from 4 brands — BCA, NATIONAL, SCHAEFFLER and 1 other brand.

This group includes BCA NS99177, NATIONAL 99177 and SCHAEFFLER SR3499 and the remaining parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

22 Crankshaft Seal parts for the 2008 Chrysler Crossfire come from 10 brands — FEL-PRO, ELRING, VICTOR REINZ and 7 other brands. The "Popular" part is ELRING 466042.

This table covers the cylinder heads that close the top of the block. Read more

2 Cylinder Head parts for the 2008 Chrysler Crossfire come from MOPAR.

This group includes MOPAR 5096475AA and MOPAR 5096476AA.

This table covers the bolts that clamp the cylinder head to the block. Read more

6 Cylinder Head Bolt parts are listed for the 2008 Chrysler Crossfire, from AJUSA, ELRING, APEX and 3 other brands. AJUSA 81050800 carries the "Popular" badge.

Listed part numbers: AJUSA 81050800, ELRING 759970 and APEX AHB914, plus the other parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

14 Cylinder Head Gasket parts are listed for the 2008 Chrysler Crossfire, from ELRING, FEL-PRO, AJUSA and 4 other brands. ELRING 104600 carries the "Popular" badge.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

10 Cylinder Head Gasket Set parts are listed for the 2008 Chrysler Crossfire, from FEL-PRO, ELRING, VICTOR REINZ and 4 other brands. APEX AHS9014 carries the "Popular" badge.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

2 Engine Block Heater parts for the 2008 Chrysler Crossfire come from 2 brands — KAT'S HEATERS and MOPAR.

This group includes KAT'S HEATERS 11483 and MOPAR 5099809AA.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 2008 Chrysler Crossfire — AJUSA 50231800.

This table covers the brackets that mount the Engine Lift. Typical signs include a cracked mount, a rattle, or a bracket that no longer holds alignment. Confirm position in the notes. Many brackets look alike and bolt to different corners. Read more

MOPAR supplies both parts for the 2008 Chrysler Crossfire.

Listed part numbers: MOPAR 5097162AA and MOPAR 5097163AA.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 2008 Chrysler Crossfire — MOPAR 5096861AB.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

3 Harmonic Balancer parts are listed for the 2008 Chrysler Crossfire, from SKP, ATP and DAYCO.

In the Economy grade, SKP supplies 1 part: the catalog's value-priced group. A representative part number is SKP SK594415.

The Standard Replacement section lists 2 options from ATP and DAYCO — built to original-equipment specification. ATP 102377 is listed in this group.

This group includes SKP SK594415, ATP 102377 and DAYCO PB1700N.

This table covers the Intake manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

This group shows a single part: MOPAR 5179739AA.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

9 Intake Manifold Gasket parts are listed for the 2008 Chrysler Crossfire, from VICTOR REINZ, FEL-PRO, MAHLE / CLEVITE and 5 other brands. FEL-PRO MS97091 carries the "Popular" badge.

Part numbers include FEL-PRO MS97091, MAHLE / CLEVITE MS19392 and AJUSA 13190200, among others listed above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: MOPAR 5097170AB.

This table covers the long-block engine assemblies (block, crank, heads). Read more

One part is listed for the 2008 Chrysler Crossfire — MOPAR 5096472AA.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

3 Motor Mount parts for the 2008 Chrysler Crossfire come from 3 brands — ANCHOR, DEA / MARMON RIDE CONTROL and WESTAR.

Part numbers include ANCHOR 9853, DEA / MARMON RIDE CONTROL A5693 and WESTAR EM7130.

This table covers the isolators in an engine mount. Read more

One part is listed for the 2008 Chrysler Crossfire — MOPAR 5098310AB.

This table covers the Motor Mount kits. Read more

This group shows a single part: ANCHOR 301131.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

12 Oil parts for the 2008 Chrysler Crossfire come from 4 brands — VALVOLINE, MOBIL, LIQUI MOLY and 1 other brand. The "Popular" part is MOBIL 112628.

The Full Synthetic section lists 10 options from VALVOLINE, MOBIL, LIQUI MOLY and 1 other brand — full-synthetic oils. MOBIL 112628 is listed in this group.

The Synthetic Blend section lists 2 options from VALVOLINE — synthetic-blend oils. VALVOLINE 797975 is listed in this group.

This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

ELRING supplies both parts for the 2008 Chrysler Crossfire.

Listed part numbers: ELRING 130250 and ELRING 130240.

This table covers the Oil Cooler Hose pipes. Read more

This group shows a single part: MOPAR 5097766AA.

This table covers the Oil Dipstick tubes. Read more

This group shows a single part: MOPAR 5099318AA.

This table covers the seals at the Oil Dipstick / Tube. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2008 Chrysler Crossfire — FEL-PRO 73668.

This table covers the drain plugs in the oil pan. Read more

3 Oil Drain Plug parts for the 2008 Chrysler Crossfire come from 3 brands — AGS, DORMAN and MOPAR.

This group includes AGS ODP00007, DORMAN 090164 and MOPAR 5073945AA.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Drain Plug Gasket parts are listed for the 2008 Chrysler Crossfire, from DORMAN, ELRING, FEL-PRO and 1 other brand.

Listed part numbers: DORMAN 097135, ELRING 115100 and FEL-PRO 73352, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

6 Oil Filler Cap parts for the 2008 Chrysler Crossfire come from 6 brands — MOTORAD, ÜRO PARTS, CALORSTAT and 3 other brands. The "Popular" part is MOTORAD MO132.

Listed part numbers: MOTORAD MO132, ÜRO PARTS 1110180302 and CALORSTAT OC2327, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

20 Oil Filter parts for the 2008 Chrysler Crossfire come from 15 brands — VARIOUS MFR, FAMOUS BRAND, WIX and 12 other brands. The "Popular" part is MOBIL M1C253A.

The Economy section: 11 options from VARIOUS MFR, FAMOUS BRAND, CHAMP / LUBER-FINER and 5 other brands. CHAMP / LUBER-FINER P8153 is listed in this group.

The High Performance / Heavy Duty section lists 2 options from MOBIL and WIX — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1C253A is listed in this group.

Standard Replacement: 7 parts, from HENGST, MAHLE / CLEVITE, MANN and 3 other brands. A representative part number is HENGST E11H02D155.

This table covers the Oil Filter covers. Read more

3 Oil Filter Cover parts are listed for the 2008 Chrysler Crossfire, from DORMAN, MOTORAD and SKP.

Part numbers include DORMAN 921176, MOTORAD MO362 and SKP SK121462.

This table covers the Oil Filter housings. Read more

One part is listed for the 2008 Chrysler Crossfire — HENGST H812H.

This table covers the seals at the Oil Filter Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Oil Filter Housing Seal parts for the 2008 Chrysler Crossfire come from ELRING.

Listed part numbers: ELRING 137100 and ELRING 055330.

This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

2 Oil Level Sensor parts for the 2008 Chrysler Crossfire come from 2 brands — STANDARD MOTOR PRODUCTS and WELLS.

Part numbers include STANDARD MOTOR PRODUCTS FLS161 and WELLS 5S3017.

This table covers the oil pans that hold the engine's oil sump. Read more

6 Oil Pan parts are listed for the 2008 Chrysler Crossfire, from SKP, DORMAN, LILAND GLOBAL and 3 other brands. SKP SK264720 carries the "Popular" badge.

Listed part numbers: SKP SK264720, DORMAN 264720 and LILAND GLOBAL IMDP01A, plus the other parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts for the 2008 Chrysler Crossfire come from 4 brands — VICTOR REINZ, APEX, FEL-PRO and 1 other brand. The "Popular" part is VICTOR REINZ 703141410.

This group includes VICTOR REINZ 703141410, APEX AOP914 and FEL-PRO OS30813 and the remaining parts above.

This table covers the Rocker Arm shafts. Read more

2 Rocker Arm Shaft parts for the 2008 Chrysler Crossfire come from MOPAR.

This group includes MOPAR 5097142AA and MOPAR 5097144AA.

This table covers the Spring retainers. Read more

MOPAR supplies the 4 Spring Retainer parts for the 2008 Chrysler Crossfire.

This group includes MOPAR 5098374AA, MOPAR 52108058AA and MOPAR 52108138AB and the remaining parts above.

This table covers the Timing Cam sprockets. Read more

This group shows a single part: MOPAR 5098420AA.

This table covers the guides and dampers that keep the timing chain on its path. Read more

MOPAR supplies both parts for the 2008 Chrysler Crossfire.

Part numbers include MOPAR 5099338AA and MOPAR 5101533AA.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: MAHLE / CLEVITE JV5078.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts for the 2008 Chrysler Crossfire come from 2 brands — MAHLE / CLEVITE and SKF.

Listed part numbers: MAHLE / CLEVITE 67769 and SKF 17733.

This table covers the Valve covers. Read more

MOPAR supplies both parts for the 2008 Chrysler Crossfire.

This group includes MOPAR 5096479AA and MOPAR 5096480AA.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

12 Valve Cover Gasket parts for the 2008 Chrysler Crossfire come from 6 brands — MAHLE / CLEVITE, VICTOR REINZ, ELRING and 3 other brands. The "Popular" part is ELRING 130270.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

2 Valve Guide parts for the 2008 Chrysler Crossfire come from MOPAR.

Part numbers include MOPAR 5101538AA and MOPAR 5101539AA.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

2 Valve Lifter parts for the 2008 Chrysler Crossfire come from AJUSA.

Part numbers include AJUSA 85012500 and AJUSA 85012400.

This table covers the Valve seats. Read more

One part is listed for the 2008 Chrysler Crossfire — MOPAR 5098921AA.

This table covers the springs that close each intake and exhaust valve. Typical signs include a sagging corner, a broken coil, or a clunk from the spring pocket. Replace springs in axle pairs and inspect the seats. Read more

One part is listed for the 2008 Chrysler Crossfire — MOPAR 5096541AA.

This table covers the Valve Spring retainers. Read more

One part is listed for the 2008 Chrysler Crossfire — MOPAR 5099282AA.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Valve Stem Seal parts for the 2008 Chrysler Crossfire come from 5 brands — ELRING, VICTOR REINZ, MAHLE / CLEVITE and 2 other brands. The "Popular" part is ELRING 830489.

This group includes ELRING 830489, MAHLE / CLEVITE SS45945 and APEX AVS9014 and the remaining parts above.