2011 Chrysler 300 Drivetrain Parts

This table covers the actuators that engage four-wheel drive at the transfer case or axle. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

One part is listed for the 2011 Chrysler 300 — STANDARD MOTOR PRODUCTS TCA118.

This table covers the Axle / Differential assemblies. Read more

MOPAR supplies both parts for the 2011 Chrysler 300.

Listed part numbers: MOPAR 4593844AA and MOPAR 4593853AA.

This table covers the Axle housings. Read more

This group shows a single part: MOPAR 5143949AA.

This table covers the seals where an axle shaft exits the housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Axle Shaft Seal parts for the 2011 Chrysler 300 come from 4 brands — TIMKEN, SKF, ELRING and 1 other brand. The "Popular" part is SKF 18547A. 3 parts fit every engine; the other 5 are engine-specific.

Part numbers include SKF 18547A, TIMKEN SL260185 and ELRING B12920, among others listed above.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

36 CV Axle parts for the 2011 Chrysler 300 come from 8 brands — TRAKMOTIVE, GSP, TOP NOTCH and 5 other brands. The "Popular" part is FAMOUS BRAND NCV479097. Economy and Standard Replacement are all represented, and Standard Replacement alone accounts for 32 parts.

This table covers the CV Intermediate shafts. Read more

One part is listed for the 2011 Chrysler 300 — DORMAN 630347.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

4 CV Joint Boot parts for the 2011 Chrysler 300 come from 2 brands — MEVOTECH and MOPAR. 3 parts fit every engine; the other 1 is engine-specific.

Listed part numbers: MEVOTECH DX516, MEVOTECH DX571 and MOPAR 5142215AA, plus the other parts above.

This table covers the bearings and races that support the differential carrier. Read more

17 Differential Carrier Bearing / Race parts for the 2011 Chrysler 300 come from 5 brands — WJB / INMOTION PARTS, BCA, SKF and 2 other brands. The "Popular" part is WJB / INMOTION PARTS WT32010X. 5 parts fit every engine; the other 12 are engine-specific.

The Economy section lists 5 options from WJB / INMOTION PARTS — the catalog's value-priced group. WJB / INMOTION PARTS WT32010X is listed in this group.

In the Standard Replacement grade, BCA, SKF, SCHAEFFLER and 1 other brand supply 12 parts: built to original-equipment specification. A representative part number is BCA NBLM503349A.

This table covers the Differential Carrier bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: ENERGY SUSPENSION 51115G.

This table covers the Differential covers. Read more

One part is listed for the 2011 Chrysler 300 — MOPAR 5143120AA.

This table covers the Differential Cover bolts. Read more

This group shows a single part: MOPAR 5143143AA.

This table covers the gaskets that seal the Differential Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: ELRING B12900.

This table covers the Differential mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

MOPAR supplies the 3 Differential Mount parts for the 2011 Chrysler 300.

This group includes MOPAR 4578191AA, MOPAR 4578084AC and MOPAR 4578085AA.

This table covers the bearings and races on the differential pinion. Read more

32 Differential Pinion Bearing / Race parts are listed for the 2011 Chrysler 300, from BCA, WJB / INMOTION PARTS, FAMOUS BRAND and 5 other brands. WJB / INMOTION PARTS WTM86610 carries the "Popular" badge. They are grouped as Economy and Standard Replacement, with Standard Replacement the largest group at 21 parts from BCA, NATIONAL, SCHAEFFLER and 2 other brands.

This table covers the flanges that connect the driveshaft to the differential pinion. Read more

This group shows a single part: DORMAN 697630.

This table covers the wear sleeves used to restore a grooved pinion seal surface. Read more

2 Differential Pinion Repair Sleeve parts for the 2011 Chrysler 300 come from 2 brands — BCA and WJB / INMOTION PARTS.

Part numbers include BCA NS99139 and WJB / INMOTION PARTS WS99139.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

6 Differential Pinion Seal parts for the 2011 Chrysler 300 come from 3 brands — WJB / INMOTION PARTS, NATIONAL and SKF. The "Popular" part is NATIONAL 710996.

Listed part numbers: NATIONAL 710996, NATIONAL 710998 and SKF 23255A, plus the other parts above.

This table covers the Differential Pinion shims. Read more

5 Differential Pinion Shim parts for the 2011 Chrysler 300 come from MOPAR.

Part numbers include MOPAR 5142921AA, MOPAR 5142922AA and MOPAR 5142923AA, among others listed above.

This table covers the ring-and-pinion gear sets that set the axle ratio. Read more

This group shows a single part: RICHMOND 4901641.

This table covers the seals at the Differential. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Differential Seal parts are listed for the 2011 Chrysler 300, from MOPAR, NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: MOPAR 5161591AA, NATIONAL 711050 and WJB / INMOTION PARTS WS711050.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

9 Drive Shaft parts are listed for the 2011 Chrysler 300, from DORMAN, TOP NOTCH, CARDONE and 3 other brands. TOP NOTCH TN1242PS carries the "Popular" badge.

This group includes TOP NOTCH TN1242PS, TOP NOTCH TN1243PS and CARDONE 653000 and the remaining parts above.

This table covers the Drive Shaft Center Support bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

10 Drive Shaft Center Support Bearing parts are listed for the 2011 Chrysler 300, from DORMAN, DEA / MARMON RIDE CONTROL, WESTAR and 7 other brands. DORMAN 934301 carries the "Popular" badge.

Economy: 4 parts, from DORMAN, DEA / MARMON RIDE CONTROL, WESTAR and 1 other brand. A representative part number is DORMAN 934301.

The Standard Replacement section: 6 options from DANA, ANCHOR, BCA and 3 other brands. DANA 252110201X is listed in this group.

This table covers the flex joints in the driveshaft. Read more

9 Drive Shaft Flex Joint parts for the 2011 Chrysler 300 come from 6 brands — MOOG, SKF, ULTRA-POWER and 3 other brands.

Listed part numbers: AAE FJC0109, DORMAN 935601 and MOOG 671, plus the other parts above.