This page lists 2 ignition parts for the 1968 Datsun Pickup, across 2 part types, covering the 1.3L L4 engine. Every part shows its brand, manufacturer part number and fitment notes.
On the 1968 Datsun Pickup, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules. All 2 listed parts are Condenser / Capacitor (1 part) and Distributor Rotor (1 part).
The 1968 Datsun Pickup came with a single engine, the 1.3L L4, and every part is verified against it.
Every ignition part listed for the 1968 Datsun Pickup comes from WELLS.
Each part number listed for the 1968 Datsun Pickup opens a page with every vehicle that part fits.
Condenser / Capacitor
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| WELLS | 5H1049 | 🇲🇽 MX | Standard Duty | View on Amazon |
This table covers the capacitors used in this electrical or A/C circuit.
This group shows a single part: WELLS 5H1049.
Distributor Rotor
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| WELLS | 4R1105 | 🇲🇽 MX | Contact Material: Brass | View on Amazon |
This table covers the Distributor rotors. Typical signs include shudder under braking, or a lip at the outer edge. Do not put new pads on a rotor that is below minimum thickness.
One part is listed for the 1968 Datsun Pickup — WELLS 4R1105.
Buying Ignition Parts for a 1968 Datsun Pickup
On this vehicle, the ignition system delivers spark at the right moment — plugs, coils, wires, distributors and ignition modules.
- Confirm you have the 1.3L L4 engine — every part on this page is matched to it.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Condenser / Capacitor and Distributor Rotor .
Frequently Asked Questions
How many ignition parts fit the 1968 Datsun Pickup?
Our catalog currently lists 2 ignition parts for the 1968 Datsun Pickup across 2 subcategories and 1 brand, covering the 1.3L L4 engine. Each part is matched to the engine(s) it fits.
What are the signs of ignition problems on a 1968 Datsun Pickup?
Common symptoms include misfires under load, rough idle, flashing check-engine light, or poor starting in damp weather. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace plugs and wires (or coil boots) as a set — one weak cylinder makes the whole set feel bad.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 1968 Datsun Pickup was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 1968 Datsun Pickup?
Every part on this page is matched to the 1.3L L4 engine. Then gap matters even on “pre-gapped” plugs — verify against spec, and replace coil boots when they come off a high-mileage engine. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 1968 Datsun Pickup
Ignition Parts for Other Datsun Pickup Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.