4 Wheel parts are listed for the 2011 Ferrari 458, in 1 part type, covering the 4.5L V8 engine. Each one has a brand, a manufacturer part number and notes that say where it fits.
The wheel hardware on the 2011 Ferrari 458 covers lug nuts, studs, hub caps, TPMS sensors and trim rings. Every listed part is a Tire Pressure Monitoring System (TPMS) Sensor.
Every part on this page is matched to the 4.5L V8 — the only engine offered in the 2011 Ferrari 458.
The most listed brands for 2011 Ferrari 458 wheel parts are ULTRA-POWER (1 part), BH SENS (1 part) and DENSO (1 part), plus 1 more brand. Quality grades include OE Replacement and Aftermarket / Multi-Application.
Each part number listed for the 2011 Ferrari 458 opens a page with every vehicle that part fits.
Tire Pressure Monitoring System (TPMS) Sensor
Aftermarket / Multi-Application (Programmed)
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ULTRA-POWER | TPM3 | 🇺🇸 US 🇨🇦 CA | Tire Pressure Monitoring System Sensorwith 433 MHz Sensor | View on Amazon |
OE Replacement (Programmed)
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| BH SENS | RDE048V21 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | OE Quality 433MHZ Replacement SensorNo Programming Required | View on Amazon |
| DENSO | 5501911 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | OE ManufacturedProgrammed | View on Amazon |
| STANDARD MOTOR PRODUCTS | TPM3 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Core Material: Nickel Coated CoreProgrammed | View on Amazon |
This table covers the TPMS sensors mounted in each wheel. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors.
4 Tire Pressure Monitoring System (TPMS) Sensor parts for the 2011 Ferrari 458 come from 4 brands — ULTRA-POWER, BH SENS, DENSO and 1 other brand.
The Aftermarket / Multi-Application (Programmed) section lists 1 option from ULTRA-POWER — grouped under the catalog's "Aftermarket / Multi-Application (Programmed)" designation — the notes column spells out what sets them apart. ULTRA-POWER TPM3 is listed in this group.
In the OE Replacement (Programmed) grade, BH SENS, DENSO and STANDARD MOTOR PRODUCTS supply 3 parts: manufactured to match the original-equipment part in form, fit and function. A representative part number is BH SENS RDE048V21.
Listed part numbers: ULTRA-POWER TPM3, BH SENS RDE048V21 and DENSO 5501911, plus the other parts above.
Buying Wheel Parts for a 2011 Ferrari 458
On this vehicle, the wheel hardware covers lug nuts, studs, hub caps, TPMS sensors and trim rings.
- Confirm you have the 4.5L V8 engine — every part on this page is matched to it.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace the TPMS service kit (valve core, seal, nut) with every tire change on sensor-equipped wheels.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Tire Pressure Monitoring System (TPMS) Sensor .
Frequently Asked Questions
How many wheel parts fit the 2011 Ferrari 458?
Our catalog currently lists 4 wheel parts for the 2011 Ferrari 458 across 1 subcategory and 4 brands, covering the 4.5L V8 engine. Each part is matched to the engine(s) it fits.
What are the signs of wheel problems on a 2011 Ferrari 458?
Common symptoms include a TPMS light that will not clear, vibration after a wheel was serviced, or studs damaged by past over-torquing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What should I replace at the same time?
Where labor overlaps, replace the TPMS service kit (valve core, seal, nut) with every tire change on sensor-equipped wheels.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2011 Ferrari 458 was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 2011 Ferrari 458?
Every part on this page is matched to the 4.5L V8 engine. Then always torque lug nuts to spec in a star pattern — impact guns without torque sticks warp rotors and stretch studs. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 2011 Ferrari 458
Wheel Parts for Other Ferrari 458 Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.