1980 Fiat Brava Engine Parts

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

3 Camshaft Repair Sleeve parts for the 1980 Fiat Brava come from 3 brands — NATIONAL, SKF and WJB / INMOTION PARTS.

This group includes NATIONAL 99114 and WJB / INMOTION PARTS WS99114 and the remaining parts above.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Camshaft Seal parts for the 1980 Fiat Brava come from 7 brands — BCA, NATIONAL, AJUSA and 4 other brands. The "Popular" part is BCA NS223035.

Part numbers include BCA NS223035, NATIONAL 223035 and AJUSA 15009700, among others listed above.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Connecting Rod Bearing parts are listed for the 1980 Fiat Brava, from ITM ENGINE COMPONENTS, KING ENGINE BEARINGS and MAHLE / CLEVITE.

This group includes ITM ENGINE COMPONENTS 4B2825, KING ENGINE BEARINGS CR4488AM and MAHLE / CLEVITE CB1138AL.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 1980 Fiat Brava — AJUSA 54009700.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Crankshaft Main Bearing parts for the 1980 Fiat Brava come from 2 brands — ITM ENGINE COMPONENTS and KING ENGINE BEARINGS.

Listed part numbers: ITM ENGINE COMPONENTS 5M2826 and KING ENGINE BEARINGS MB562AM.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

3 Crankshaft Repair Sleeve parts for the 1980 Fiat Brava come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

Part numbers include BCA NS99157, NATIONAL 99157 and WJB / INMOTION PARTS WS99157.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Crankshaft Seal parts for the 1980 Fiat Brava come from 5 brands — NATIONAL, WJB / INMOTION PARTS, AJUSA and 2 other brands. The "Popular" part is NATIONAL 224025.

Listed part numbers: NATIONAL 224025, WJB / INMOTION PARTS WS224025 and AJUSA 15033900, plus the other parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Cylinder Head Gasket parts are listed for the 1980 Fiat Brava, from AJUSA, MAHLE / CLEVITE and VICTOR REINZ.

Part numbers include AJUSA 10004800, MAHLE / CLEVITE 3635 and VICTOR REINZ 613180000.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Cylinder Head Gasket Set parts are listed for the 1980 Fiat Brava, from AJUSA, ITM ENGINE COMPONENTS, MAHLE / CLEVITE and 1 other brand.

Listed part numbers: AJUSA 52011200, ITM ENGINE COMPONENTS 0916323 and MAHLE / CLEVITE HS3635X, plus the other parts above.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

This group shows a single part: KAT'S HEATERS 11401.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

One part is listed for the 1980 Fiat Brava — AJUSA 50045000.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: ITM ENGINE COMPONENTS RX34400.

This table covers the Expansion plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

DORMAN supplies the 4 Expansion Plug parts for the 1980 Fiat Brava.

Listed part numbers: DORMAN 555027, DORMAN 568009 and DORMAN 565027, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Intake Manifold Gasket parts are listed for the 1980 Fiat Brava, from AJUSA, ITM ENGINE COMPONENTS, MAHLE / CLEVITE and 1 other brand.

Listed part numbers: AJUSA 13026200, ITM ENGINE COMPONENTS 0956300 and MAHLE / CLEVITE MS15244, plus the other parts above.

This table covers the O-rings that seal this joint. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove. Read more

This group shows a single part: VICTOR REINZ 411043100.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

11 Oil Filter parts for the 1980 Fiat Brava come from 9 brands — VARIOUS MFR, BOSCH, FAMOUS BRAND and 6 other brands. The "Popular" part is VARIOUS MFR PG4670.

The Economy section lists 4 options from VARIOUS MFR, BOSCH, FAMOUS BRAND and 1 other brand — the catalog's value-priced group. VARIOUS MFR PG4670 is listed in this group.

The High Performance / Heavy Duty section lists 1 option from MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1204A is listed in this group.

In the Standard Replacement grade, ACDELCO, BOSCH, HASTINGS / BALDWIN and 3 other brands supply 6 parts: built to original-equipment specification. A representative part number is ACDELCO PF53.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Oil Pan Gasket parts for the 1980 Fiat Brava come from 4 brands — AJUSA, ELRING, MAHLE / CLEVITE and 1 other brand.

Part numbers include AJUSA 14030900, ELRING 671100 and MAHLE / CLEVITE OS30586, among others listed above.

This table covers the rings that seal each piston to the cylinder wall. Read more

One part is listed for the 1980 Fiat Brava — ITM ENGINE COMPONENTS 0216045.

This table covers the Thrust washers. Read more

2 Thrust Washer parts for the 1980 Fiat Brava come from 2 brands — ITM ENGINE COMPONENTS and KING ENGINE BEARINGS.

Listed part numbers: ITM ENGINE COMPONENTS 1T2826 and KING ENGINE BEARINGS TW113AM.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

One part is listed for the 1980 Fiat Brava — ITM ENGINE COMPONENTS 4071.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

2 Timing Cover Repair Sleeve parts for the 1980 Fiat Brava come from 2 brands — SCHAEFFLER and SKF.

This group includes SCHAEFFLER SS3480 and SKF 99153.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts for the 1980 Fiat Brava come from 2 brands — ITM ENGINE COMPONENTS and SKF.

This group includes ITM ENGINE COMPONENTS 1506301 and SKF 15826.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Valve Cover Gasket parts for the 1980 Fiat Brava come from 5 brands — ITM ENGINE COMPONENTS, AJUSA, FEL-PRO and 2 other brands. The "Popular" part is AJUSA 11002700.

This group includes AJUSA 11002700, FEL-PRO VS26065C and BECK/ARNLEY 0360263 and the remaining parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

2 Valve Guide parts for the 1980 Fiat Brava come from ITM ENGINE COMPONENTS.

Listed part numbers: ITM ENGINE COMPONENTS VG1147CI and ITM ENGINE COMPONENTS VG1147BR.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

One part is listed for the 1980 Fiat Brava — ITM ENGINE COMPONENTS 051101.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Valve Stem Seal parts for the 1980 Fiat Brava come from 3 brands — AJUSA, ELRING and ITM ENGINE COMPONENTS.

This group includes AJUSA 12004500, AJUSA 57004900 and ELRING 197378 and the remaining parts above.