1997 Geo Tracker Engine Parts

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

3 Camshaft Repair Sleeve parts are listed for the 1997 Geo Tracker, from NATIONAL, SKF and WJB / INMOTION PARTS.

This group includes NATIONAL 99128 and WJB / INMOTION PARTS WS99128 and the remaining parts above.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

8 Camshaft Seal parts are listed for the 1997 Geo Tracker, from FEL-PRO, NATIONAL, AJUSA and 5 other brands. FEL-PRO TCS45852 carries the "Popular" badge.

This group includes FEL-PRO TCS45852, NATIONAL 710310 and AJUSA 15010600 and the remaining parts above.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

7 Connecting Rod Bearing parts for the 1997 Geo Tracker come from 6 brands — MAHLE / CLEVITE, ENGINETECH, ITM ENGINE COMPONENTS and 3 other brands. The "Popular" part is ENGINETECH BB8340.

This group includes ENGINETECH BB8340, MAHLE / CLEVITE CB1477A4 and ITM ENGINE COMPONENTS 4B9549 and the remaining parts above.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Conversion / Lower Gasket Set parts for the 1997 Geo Tracker come from 6 brands — APEX, ENGINETECH, AJUSA and 3 other brands. The "Popular" part is APEX ACS7006.

Listed part numbers: APEX ACS7006, ENGINETECH SU16CS and AJUSA 54124100, plus the other parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Crankshaft Main Bearing parts are listed for the 1997 Geo Tracker, from TOPLINE, ENGINETECH, MAHLE / CLEVITE and 2 other brands. ENGINETECH BC8339 carries the "Popular" badge.

Part numbers include ENGINETECH BC8339, MAHLE / CLEVITE MS1820A and ITM ENGINE COMPONENTS 5M9378, among others listed above.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

2 Crankshaft Repair Sleeve parts are listed for the 1997 Geo Tracker, from NATIONAL and WJB / INMOTION PARTS.

This group includes NATIONAL 99128 and WJB / INMOTION PARTS WS99128.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

16 Crankshaft Seal parts are listed for the 1997 Geo Tracker, from FEL-PRO, NATIONAL, WJB / INMOTION PARTS and 7 other brands. FEL-PRO TCS45895 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

3 Cylinder Head Bolt parts for the 1997 Geo Tracker come from 3 brands — APEX, SKP and TOPLINE.

This group includes APEX AHB706, SKP SKAHB706 and TOPLINE HBSZ5.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts for the 1997 Geo Tracker come from 6 brands — APEX, FEL-PRO, ENGINETECH and 3 other brands. The "Popular" part is APEX AHG703.

Listed part numbers: APEX AHG703, FEL-PRO 9683PT1 and ENGINETECH HSU16A, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

6 Cylinder Head Gasket Set parts for the 1997 Geo Tracker come from 6 brands — APEX, ENGINETECH, AJUSA and 3 other brands. The "Popular" part is APEX AHS7006.

Part numbers include APEX AHS7006, ENGINETECH SU16HSA and AJUSA 52098500, among others listed above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 1997 Geo Tracker — GM GENUINE 94033681.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

One part is listed for the 1997 Geo Tracker — KAT'S HEATERS 16400.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

5 Engine Kit Gasket Set parts for the 1997 Geo Tracker come from 5 brands — ENGINETECH, AJUSA, APEX and 2 other brands. The "Popular" part is ENGINETECH SU16K2.

This group includes ENGINETECH SU16K2, AJUSA 50111500 and APEX AFS7006 and the remaining parts above.

This table covers the Engine rebuild kits. Read more

This group shows a single part: ENGINETECH RCGM16BP.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Exhaust Valve parts are listed for the 1997 Geo Tracker, from ENGINETECH, ITM ENGINE COMPONENTS, QUALCAST and 2 other brands. ENGINETECH EM2697 carries the "Popular" badge.

Listed part numbers: ENGINETECH EM2697, ITM ENGINE COMPONENTS RX9541 and QUALCAST 1010517, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Intake Manifold Gasket parts for the 1997 Geo Tracker come from 6 brands — APEX, FEL-PRO, AJUSA and 3 other brands. The "Popular" part is APEX AMS7060.

This group includes APEX AMS7060, FEL-PRO MS95402 and AJUSA 13080500 and the remaining parts above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 1997 Geo Tracker — APEX AMS7062.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

5 Intake Valve parts are listed for the 1997 Geo Tracker, from ENGINETECH, ITM ENGINE COMPONENTS, QUALCAST and 2 other brands. ENGINETECH IM2696 carries the "Popular" badge.

Part numbers include ENGINETECH IM2696, ITM ENGINE COMPONENTS RV9538 and QUALCAST 1010516, among others listed above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Motor Mount parts are listed for the 1997 Geo Tracker, from ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand.

Part numbers include ANCHOR 8568, DEA / MARMON RIDE CONTROL A6827 and PIONEER 602856, among others listed above.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

22 Oil parts are listed for the 1997 Geo Tracker, from MOBIL, VALVOLINE and IDEMITSU. MOBIL 125195 carries the "Popular" badge.

In the Conventional grade, VALVOLINE supplies 3 parts: grouped under the catalog's "Conventional" designation — the notes column spells out what sets them apart. A representative part number is VALVOLINE 797578.

In the Full Synthetic grade, MOBIL and VALVOLINE supply 8 parts: full-synthetic oils. A representative part number is MOBIL 125195.

The High Mileage (>75,000 Miles) section lists 8 options from MOBIL and VALVOLINE — oils grouped for high-mileage engines. MOBIL 103767 is listed in this group.

In the Racing grade, IDEMITSU supplies 1 part: grouped under the catalog's "Racing" designation — the notes column spells out what sets them apart. A representative part number is IDEMITSU 30018100750.

In the Synthetic Blend grade, MOBIL supplies 2 parts: synthetic-blend oils. A representative part number is MOBIL 124406.

This table covers the Oil Cooler Mounting kits. Read more

2 Oil Cooler Mounting Kit parts for the 1997 Geo Tracker come from HAYDEN.

Part numbers include HAYDEN 238 and HAYDEN 153.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts are listed for the 1997 Geo Tracker, from DORMAN, AGS, ENGINETECH and 1 other brand. AGS ODP00007 carries the "Popular" badge.

This group includes AGS ODP00007, DORMAN 090053 and DORMAN 090075 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts for the 1997 Geo Tracker come from 4 brands — DORMAN, FEL-PRO, JAPANESE OE and 1 other brand. The "Popular" part is DORMAN 095147.

Part numbers include DORMAN 095147, DORMAN 995147CD and FEL-PRO 73351, among others listed above.

This table covers the caps on the oil filler neck. Read more

5 Oil Filler Cap parts are listed for the 1997 Geo Tracker, from BECK/ARNLEY, MOTORAD, GATES and 1 other brand. MOTORAD MO81 carries the "Popular" badge.

Listed part numbers: MOTORAD MO81, BECK/ARNLEY 0160131 and BECK/ARNLEY 0160125, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts are listed for the 1997 Geo Tracker, from BOSCH, VARIOUS MFR, WIX and 9 other brands. WIX 51348XP carries the "Popular" badge.

In the Economy grade, BOSCH, FRAM, FVP and 2 other brands supply 5 parts: the catalog's value-priced group. A representative part number is BOSCH 72161WS.

In the High Performance / Heavy Duty grade, WIX and MOBIL supply 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 51348XP.

The Standard Replacement section lists 10 options from MOTORCRAFT, HASTINGS / BALDWIN, BOSCH and 5 other brands — built to original-equipment specification. BOSCH 3330 is listed in this group.

This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors. Read more

One part is listed for the 1997 Geo Tracker — WELLS 1S6556.

This table covers the oil pans that hold the engine's oil sump. Read more

3 Oil Pan parts for the 1997 Geo Tracker come from 3 brands — ATP, PIONEER and SPECTRA PREMIUM.

Part numbers include ATP 103269, PIONEER 501118 and SPECTRA PREMIUM GMP38A.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Pan Gasket parts are listed for the 1997 Geo Tracker, from VICTOR REINZ, AJUSA, APEX and 2 other brands. VICTOR REINZ 703141410 carries the "Popular" badge.

Part numbers include VICTOR REINZ 703141410, AJUSA 14063000 and APEX AOP706, among others listed above.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

5 Oil Pump parts are listed for the 1997 Geo Tracker, from SKP, ENGINETECH, ITM ENGINE COMPONENTS and 2 other brands. ENGINETECH EP005A carries the "Popular" badge.

Economy: 1 part, from SKP. A representative part number is SKP SKOM238.

The Standard Replacement section: 4 options from ENGINETECH, ITM ENGINE COMPONENTS, MELLING and 1 other brand. ENGINETECH EP005A is listed in this group.

This group includes ENGINETECH EP005A, SKP SKOM238 and ITM ENGINE COMPONENTS 0571328 and the remaining parts above.

This table covers the gaskets that seal the Oil Pump. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: BECK/ARNLEY 0398011.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

3 Piston parts for the 1997 Geo Tracker come from 2 brands — ENGINETECH and TOPLINE.

This group includes ENGINETECH P4630, ENGINETECH K46304P and TOPLINE PASZ5.

This table covers the rings that seal each piston to the cylinder wall. Read more

5 Piston Ring parts for the 1997 Geo Tracker come from 5 brands — ENGINETECH, MAHLE / CLEVITE, HASTINGS MANUFACTURING and 2 other brands. The "Popular" part is ENGINETECH S75254.

In the Premium grade, ENGINETECH and MAHLE / CLEVITE supply 2 parts: a step above OE specification in materials, tolerances or warranty terms. A representative part number is ENGINETECH S75254.

Standard Replacement: 3 parts, from HASTINGS MANUFACTURING, ITM ENGINE COMPONENTS and TOPLINE. A representative part number is HASTINGS MANUFACTURING 2C4901.

Part numbers include ENGINETECH S75254, MAHLE / CLEVITE 41612 and HASTINGS MANUFACTURING 2C4901, among others listed above.

This table covers the Re-Ring kits. Read more

One part is listed for the 1997 Geo Tracker — ENGINETECH RMGM16BP.

This table covers the rocker arms that transfer cam motion to the valves. Read more

One part is listed for the 1997 Geo Tracker — TOPLINE RASZ5I.

This table covers the Thrust washers. Read more

4 Thrust Washer parts are listed for the 1997 Geo Tracker, from ENGINETECH, ITM ENGINE COMPONENTS, KING ENGINE BEARINGS and 1 other brand.

Listed part numbers: ENGINETECH TW8339, ITM ENGINE COMPONENTS 1T1000 and KING ENGINE BEARINGS TW144AM, plus the other parts above.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

10 Timing Belt parts for the 1997 Geo Tracker come from 10 brands — CLOYES, ITM ENGINE COMPONENTS, GATES and 7 other brands. The "Popular" part is CLOYES B212.

The Economy section: 2 options from CLOYES and ITM ENGINE COMPONENTS. CLOYES B212 is listed in this group.

Standard Replacement: 8 parts, from GATES, ACDELCO, BANDO and 5 other brands. A representative part number is GATES T212.

This table covers the Timing Belt & component kits. Read more

10 Timing Belt & Component Kit parts are listed for the 1997 Geo Tracker, from CONTINENTAL, INA, CLOYES and 5 other brands. CLOYES BK212 carries the "Popular" badge.

Economy: 2 parts, from CLOYES and CONTINENTAL. A representative part number is CLOYES BK212.

The Standard Replacement section: 8 options from INA, ITM ENGINE COMPONENTS, ACDELCO and 4 other brands. ITM ENGINE COMPONENTS ITM212 is listed in this group.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

One part is listed for the 1997 Geo Tracker — GMB 4658640.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

11 Timing Belt Tensioner parts are listed for the 1997 Geo Tracker, from S.A. GEAR, CLOYES, ACDELCO and 7 other brands. CLOYES 95282 carries the "Popular" badge.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Timing Cover Gasket parts are listed for the 1997 Geo Tracker, from MAHLE / CLEVITE and ULTRA-POWER.

Part numbers include MAHLE / CLEVITE JV1047 and MAHLE / CLEVITE JV1110, among others listed above.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

One part is listed for the 1997 Geo Tracker — SKF 99128.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 1997 Geo Tracker — SKF 12724.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

5 Torque Strut Mount parts for the 1997 Geo Tracker come from 3 brands — ANCHOR, WESTAR and DEA / MARMON RIDE CONTROL. The "Popular" part is ANCHOR 8657.

This group includes ANCHOR 8657, ANCHOR 8656 and DEA / MARMON RIDE CONTROL A6815 and the remaining parts above.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Valve Cover Gasket parts are listed for the 1997 Geo Tracker, from APEX, FEL-PRO, ITM ENGINE COMPONENTS and 2 other brands. APEX AVC706S carries the "Popular" badge.

Listed part numbers: APEX AVC706S, FEL-PRO VS50473R and APEX AVC706, plus the other parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

5 Valve Guide parts are listed for the 1997 Geo Tracker, from ITM ENGINE COMPONENTS, SBI, QUALCAST and 1 other brand. SBI 1408324 carries the "Popular" badge.

Part numbers include SBI 1408324, ITM ENGINE COMPONENTS VG1056CI and ITM ENGINE COMPONENTS VG1056BR, among others listed above.

This table covers the Valve seats. Read more

4 Valve Seat parts for the 1997 Geo Tracker come from 3 brands — SBI, DURA-BOND and QUALCAST.

Part numbers include DURA-BOND 31047, QUALCAST 21106250 and SBI SB125054, among others listed above.

This table covers the Valve Spring retainers. Read more

This group shows a single part: ITM ENGINE COMPONENTS 051221.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

5 Valve Spring Retainer Keeper parts for the 1997 Geo Tracker come from 4 brands — PIONEER, SBI, MELLING and 1 other brand. The "Popular" part is SBI 1211060.

Part numbers include SBI 1211060, MELLING VL1060 and PIONEER PF555HD, among others listed above.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Valve Stem Seal parts are listed for the 1997 Geo Tracker, from FEL-PRO, APEX, ITM ENGINE COMPONENTS and 2 other brands. FEL-PRO SS70360 carries the "Popular" badge.

Part numbers include FEL-PRO SS70360, APEX AVS7002 and ITM ENGINE COMPONENTS SS273, among others listed above.