2000 Honda CR-V Drivetrain Parts

This table covers the seals where an axle shaft exits the housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

TIMKEN supplies both parts for the 2000 Honda CR-V.

Listed part numbers: TIMKEN 710629 and TIMKEN SL260470.

This table covers the complete CV axle shafts from differential (or hub) to wheel. Typical signs include a click in tight turns, grease flung around the wheel well, or a vibration that builds with speed. A torn boot caught early is a boot kit; caught late it is the whole axle. Torque the axle nut to the method in the notes. Read more

17 CV Axle parts are listed for the 2000 Honda CR-V, from TRAKMOTIVE, TOP NOTCH, GSP and 1 other brand. GSP NCV36546 carries the "Popular" badge.

This table covers the CV Axle Support bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

This group shows a single part: BECK/ARNLEY 0514288.

This table covers the boots that keep grease in a CV joint. Typical signs include a split boot, grease flung around the joint, or a click once grit is inside. A boot caught early is a kit. Once the joint has clicked, the joint itself is usually worn. Read more

8 CV Joint Boot parts are listed for the 2000 Honda CR-V, from DORMAN, MEVOTECH and BECK/ARNLEY. DORMAN 03680 carries the "Popular" badge.

Listed part numbers: DORMAN 03680, MEVOTECH DX610 and BECK/ARNLEY 1032314, plus the other parts above.

This table covers the bearings and races that support the differential carrier. Read more

2 Differential Carrier Bearing / Race parts are listed for the 2000 Honda CR-V, from BECK/ARNLEY and SKF.

Part numbers include BECK/ARNLEY 0513879 and SKF 6208ZJ.

This table covers the Differential Carrier bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

3 Differential Carrier Bushing parts are listed for the 2000 Honda CR-V, from BECK/ARNLEY and ENERGY SUSPENSION.

Part numbers include BECK/ARNLEY 1042421, BECK/ARNLEY 1042406 and ENERGY SUSPENSION 161114G.

This table covers the dampers that quiet the differential. Read more

3 Differential Dampener parts are listed for the 2000 Honda CR-V, from DORMAN, SKP and ULTRA-POWER.

Listed part numbers: DORMAN 924448 and SKP SK924448, plus the other parts above.

This table covers the Differential mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

2 Differential Mount parts for the 2000 Honda CR-V come from 2 brands — DEA / MARMON RIDE CONTROL and WESTAR.

Listed part numbers: DEA / MARMON RIDE CONTROL A65009 and WESTAR EM5995.

This table covers the bearings and races on the differential pinion. Read more

This group shows a single part: SCHAEFFLER KT4.

This table covers the seals at the differential pinion yoke. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Differential Pinion Seal parts are listed for the 2000 Honda CR-V, from NATIONAL and TIMKEN.

Listed part numbers: NATIONAL 711177 and TIMKEN 712551.

This table covers the driveshafts that carry torque from the transmission or transfer case. Read more

5 Drive Shaft parts for the 2000 Honda CR-V come from 5 brands — SKP, DORMAN, TRAKMOTIVE and 2 other brands. The "Popular" part is SKP SK654002.

This group includes SKP SK654002, DORMAN 936003 and TRAKMOTIVE HOP003 and the remaining parts above.

This table covers the Drive Shaft Center Support bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

5 Drive Shaft Center Support Bearing parts for the 2000 Honda CR-V come from 5 brands — DEA / MARMON RIDE CONTROL, DORMAN, WESTAR and 2 other brands. The "Popular" part is DANA 25141745X.

The Economy section lists 3 options from DEA / MARMON RIDE CONTROL, DORMAN and WESTAR — the catalog's value-priced group. DEA / MARMON RIDE CONTROL A6032 is listed in this group.

In the Standard Replacement grade, DANA and ANCHOR supply 2 parts: built to original-equipment specification. A representative part number is DANA 25141745X.

This group includes DANA 25141745X, DEA / MARMON RIDE CONTROL A6032 and DORMAN 934003 and the remaining parts above.

This table covers the gear oils specified for the axle or transfer case. Typical signs include a low-oil lamp, knocking, or oil that has gone thin before the next interval. Match the viscosity and spec in the notes, not just the weight on the bottle. Read more

VALVOLINE supplies the 3 Gear Oil parts for the 2000 Honda CR-V.

This group includes VALVOLINE VV3246, VALVOLINE 773775 and VALVOLINE 881051.

This table covers the Transfer Case Input Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Transfer Case Input Shaft Bearing parts are listed for the 2000 Honda CR-V, from SCHAEFFLER, SKF and TIMKEN.

Part numbers include SCHAEFFLER 32008XA, SKF 32008XVP and TIMKEN 207.

This table covers the wear sleeves used to restore a Transfer Case Input Shaft seal surface. Read more

2 Transfer Case Input Shaft Repair Sleeve parts for the 2000 Honda CR-V come from 2 brands — SCHAEFFLER and TIMKEN.

This group includes SCHAEFFLER SR3477 and TIMKEN KWK99149.

This table covers the seals at the Transfer Case Input Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: TIMKEN 710247.

This table covers the Transfer Case Output Shaft bearings. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

6 Transfer Case Output Shaft Bearing parts for the 2000 Honda CR-V come from 4 brands — SKF, SCHAEFFLER, WJB / INMOTION PARTS and 1 other brand. The "Popular" part is SKF L44610VP.

The Economy section: 1 option from WJB / INMOTION PARTS. WJB / INMOTION PARTS WTL44610 is listed in this group.

Standard Replacement: 5 parts, from SKF, SCHAEFFLER and TIMKEN. A representative part number is SKF L44610VP.

Listed part numbers: SKF L44610VP, WJB / INMOTION PARTS WTL44610 and SKF BR4, plus the other parts above.

This table covers the seals at the Transfer Case Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Transfer Case Output Shaft Seal parts are listed for the 2000 Honda CR-V, from SCHAEFFLER and SKF.

Listed part numbers: SCHAEFFLER SS2622 and SKF 15709.