2011 Honda CR-Z Engine Parts

This table covers the Camshaft caps. Typical signs include a leak at the neck, a cap that will not hold pressure, or a missing tether. Match the pressure rating or thread in the notes — radiator, reservoir and fuel caps are not interchangeable. Read more

One part is listed for the 2011 Honda CR-Z — AJUSA 00794900.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Camshaft Seal parts for the 2011 Honda CR-Z come from 5 brands — FEL-PRO, APEX, ELRING and 2 other brands. The "Popular" part is FEL-PRO TCS46212.

Part numbers include FEL-PRO TCS46212, APEX ATC1540 and ELRING 290710, among others listed above.

This table covers the Circular / Semi-Circular plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

2 Circular / Semi-Circular Plug parts for the 2011 Honda CR-Z come from 2 brands — APEX and VICTOR REINZ.

Part numbers include APEX ACP101 and VICTOR REINZ 711552200.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Connecting Rod Bearing parts are listed for the 2011 Honda CR-Z, from ENGINETECH, MAHLE / CLEVITE and TOPLINE.

Part numbers include ENGINETECH BB1065, MAHLE / CLEVITE CB1862A4 and TOPLINE RBH42.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts are listed for the 2011 Honda CR-Z, from AJUSA, APEX, FEL-PRO and 1 other brand.

This group includes AJUSA 54172900, APEX ACS1054 and FEL-PRO CS26529 and the remaining parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Crankshaft Main Bearing parts for the 2011 Honda CR-Z come from 2 brands — TOPLINE and ENGINETECH.

This group includes ENGINETECH BC1050, TOPLINE TWH16 and TOPLINE MBH42.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

5 Crankshaft Repair Sleeve parts for the 2011 Honda CR-Z come from 4 brands — SCHAEFFLER, BCA, NATIONAL and 1 other brand. The "Popular" part is BCA NS99315.

This group includes BCA NS99315, NATIONAL 99315 and SCHAEFFLER SR3549 and the remaining parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

16 Crankshaft Seal parts for the 2011 Honda CR-Z come from 12 brands — APEX, ELRING, SCHAEFFLER and 9 other brands. The "Popular" part is APEX ABS128.

This table covers the bolts that clamp the cylinder head to the block. Read more

6 Cylinder Head Bolt parts are listed for the 2011 Honda CR-Z, from APEX, FEL-PRO, AJUSA and 3 other brands. APEX AHB164 carries the "Popular" badge.

This group includes APEX AHB164, FEL-PRO ES72449 and AJUSA 81034300 and the remaining parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Cylinder Head Gasket parts are listed for the 2011 Honda CR-Z, from FEL-PRO, AJUSA, APEX and 2 other brands. FEL-PRO 26529PT carries the "Popular" badge.

Listed part numbers: FEL-PRO 26529PT, AJUSA 10193300 and APEX AHG167, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Cylinder Head Gasket Set parts are listed for the 2011 Honda CR-Z, from FEL-PRO, APEX, AJUSA and 3 other brands. APEX AHS1068 carries the "Popular" badge.

Listed part numbers: APEX AHS1068, FEL-PRO HS26529PT2 and AJUSA 52284200, plus the other parts above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

2 Cylinder Head Plug parts for the 2011 Honda CR-Z come from 2 brands — FEL-PRO and MAHLE / CLEVITE.

Part numbers include FEL-PRO 73868 and MAHLE / CLEVITE B32774.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

2 Engine Block Heater parts for the 2011 Honda CR-Z come from KAT'S HEATERS.

Part numbers include KAT'S HEATERS 11419 and KAT'S HEATERS 28500.

This table covers the Engine covers. Read more

TECHPRO supplies both parts for the 2011 Honda CR-Z.

Part numbers include TECHPRO HO1228127 and TECHPRO HO1228128.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Engine Kit Gasket Set parts are listed for the 2011 Honda CR-Z, from AJUSA, APEX, ITM ENGINE COMPONENTS and 1 other brand.

Listed part numbers: AJUSA 50304000, APEX AFS1068 and ITM ENGINE COMPONENTS 0900960, plus the other parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: TOPLINE EVH42L.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts are listed for the 2011 Honda CR-Z, from FEL-PRO, APEX, ELRING and 2 other brands. FEL-PRO MS97174 carries the "Popular" badge.

This group includes FEL-PRO MS97174, APEX AMS1681 and ELRING 694290 and the remaining parts above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Plenum Gasket parts for the 2011 Honda CR-Z come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO MS97178.

Part numbers include FEL-PRO MS97178, AJUSA 13232900 and APEX AMS1680, among others listed above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: TOPLINE IVH42L.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

27 Oil parts for the 2011 Honda CR-Z come from 6 brands — VALVOLINE, MOBIL, LIQUI MOLY and 3 other brands. The "Popular" part is LIQUI MOLY 2208. Grades run from Full Synthetic through High Mileage (>75,000 Miles); Full Synthetic is the most populated section, led by VALVOLINE, LIQUI MOLY, PENTOSIN and 3 other brands.

This table covers the Oil Dipstick tubes. Read more

This group shows a single part: DORMAN 921097.

This table covers the drain plugs in the oil pan. Read more

8 Oil Drain Plug parts for the 2011 Honda CR-Z come from 5 brands — DORMAN, ELRING, AGS and 2 other brands. The "Popular" part is DORMAN 090033.

This group includes DORMAN 090033, DORMAN 090053 and AGS ODP00007 and the remaining parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Drain Plug Gasket parts are listed for the 2011 Honda CR-Z, from DORMAN, FEL-PRO, AJUSA and 3 other brands. DORMAN 095144 carries the "Popular" badge.

Part numbers include DORMAN 095144, FEL-PRO 73346 and AJUSA 22007400, among others listed above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts for the 2011 Honda CR-Z come from 4 brands — CALORSTAT, DORMAN, GATES and 1 other brand.

Part numbers include CALORSTAT OC2335, DORMAN 80985 and GATES 31284, among others listed above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts for the 2011 Honda CR-Z come from 14 brands — BOSCH, VARIOUS MFR, WIX and 11 other brands. The "Popular" part is WIX 57356XP.

The Economy section lists 4 options from BOSCH, FVP, PRO-TEC and 1 other brand — the catalog's value-priced group. BOSCH 72226WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 57356XP is listed in this group.

In the Standard Replacement grade, BOSCH, DENSO, WIX and 8 other brands supply 11 parts: built to original-equipment specification. A representative part number is BOSCH 3323.

This table covers the Oil Filter Support tubes. Read more

One part is listed for the 2011 Honda CR-Z — AUTOTECNICA HA1416938.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Pan Gasket parts for the 2011 Honda CR-Z come from 5 brands — VICTOR REINZ, FEL-PRO, AJUSA and 2 other brands. The "Popular" part is FEL-PRO OS30837R.

Part numbers include FEL-PRO OS30837R, VICTOR REINZ 703141410 and AJUSA 14090600, among others listed above.

This table covers the seals at the Oil Pressure Sender / Switch. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: FEL-PRO 73196.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

3 Oil Pump parts for the 2011 Honda CR-Z come from 3 brands — SKP, MELLING and TOPLINE.

The Economy section: 1 option from SKP. SKP SKM533 is listed in this group.

Standard Replacement: 2 parts, from MELLING and TOPLINE. A representative part number is MELLING M533.

This group includes SKP SKM533, MELLING M533 and TOPLINE OPH42.

This table covers the wear sleeves used to restore a Oil Pump seal surface. Read more

3 Oil Pump Repair Sleeve parts are listed for the 2011 Honda CR-Z, from BCA, NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: BCA NS99157, NATIONAL 99157 and WJB / INMOTION PARTS WS99157.

This table covers the seals at the Oil Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Oil Pump Seal parts are listed for the 2011 Honda CR-Z, from NATIONAL and WJB / INMOTION PARTS.

Part numbers include NATIONAL 711005 and WJB / INMOTION PARTS WS711005.

This table covers the gaskets that seal the Oil Strainer. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2011 Honda CR-Z — AJUSA 01239000.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

One part is listed for the 2011 Honda CR-Z — TOPLINE PAH42L.

This table covers the rings that seal each piston to the cylinder wall. Read more

4 Piston Ring parts are listed for the 2011 Honda CR-Z, from HASTINGS MANUFACTURING, ENGINETECH and TOPLINE.

The Premium section lists 1 option from ENGINETECH — a step above OE specification in materials, tolerances or warranty terms. ENGINETECH S73124 is listed in this group.

The Standard Replacement section: 3 options from HASTINGS MANUFACTURING and TOPLINE. HASTINGS MANUFACTURING 2C5253S is listed in this group.

Part numbers include ENGINETECH S73124, HASTINGS MANUFACTURING 2C5253S and HASTINGS MANUFACTURING 2C5253, among others listed above.

This table covers the Thrust washers. Read more

2 Thrust Washer parts for the 2011 Honda CR-Z come from 2 brands — ENGINETECH and ITM ENGINE COMPONENTS.

Listed part numbers: ENGINETECH TW1516 and ITM ENGINE COMPONENTS 1T1001.

This table covers the Timing Cam sprockets. Read more

4 Timing Cam Sprocket parts for the 2011 Honda CR-Z come from 4 brands — CLOYES, FVP, INA and 1 other brand.

Listed part numbers: CLOYES S968T and INA ZSS968T, plus the other parts above.

This table covers the timing chains that keep the cams in time with the crank. Read more

4 Timing Chain parts are listed for the 2011 Honda CR-Z, from CLOYES, FVP, INA and 1 other brand.

Part numbers include CLOYES C731F and INA ZCC731F, among others listed above.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

7 Timing Chain & Component Kit parts for the 2011 Honda CR-Z come from 4 brands — S.A. GEAR, CLOYES, INA and 1 other brand. The "Popular" part is CLOYES 90731SX.

The Economy section: 2 options from S.A. GEAR. S.A. GEAR 76329S is listed in this group.

Standard Replacement: 5 parts, from CLOYES, INA and TOPLINE. A representative part number is CLOYES 90731SX.

Listed part numbers: CLOYES 90731SX, S.A. GEAR 76329S and S.A. GEAR 76329, plus the other parts above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

5 Timing Chain Guide / Damper parts are listed for the 2011 Honda CR-Z, from S.A. GEAR, CLOYES and INA. S.A. GEAR 91163 carries the "Popular" badge.

Part numbers include S.A. GEAR 91163, CLOYES 95643 and CLOYES 95642, among others listed above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

4 Timing Chain Tensioner parts for the 2011 Honda CR-Z come from 4 brands — CLOYES, FVP, INA and 1 other brand.

This group includes CLOYES 95641 and INA ZT95641 and the remaining parts above.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: MAHLE / CLEVITE JV5159.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: MAHLE / CLEVITE 67932.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

5 Timing Crank Sprocket parts for the 2011 Honda CR-Z come from 5 brands — S.A. GEAR, CLOYES, FVP and 2 other brands. The "Popular" part is S.A. GEAR S1388.

Part numbers include S.A. GEAR S1388 and CLOYES S967, among others listed above.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

6 Torque Strut Mount parts are listed for the 2011 Honda CR-Z, from DEA / MARMON RIDE CONTROL, SKP, ANCHOR and 2 other brands. SKP SKMA4574 carries the "Popular" badge.

Economy: 1 part, from SKP. A representative part number is SKP SKMA4574.

The Standard Replacement section: 5 options from DEA / MARMON RIDE CONTROL, ANCHOR, PIONEER and 1 other brand. DEA / MARMON RIDE CONTROL A4574 is listed in this group.

Part numbers include SKP SKMA4574, DEA / MARMON RIDE CONTROL A4574 and ANCHOR 9695, among others listed above.

This table covers the Valve covers. Read more

One part is listed for the 2011 Honda CR-Z — ACKOJA A260331.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Valve Cover Gasket parts for the 2011 Honda CR-Z come from 6 brands — BECK/ARNLEY, FEL-PRO, APEX and 3 other brands. The "Popular" part is BECK/ARNLEY 0361976.

Listed part numbers: BECK/ARNLEY 0361976, FEL-PRO VS50785R and APEX AVC168, plus the other parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

5 Valve Guide parts for the 2011 Honda CR-Z come from 3 brands — SBI, QUALCAST and TOPLINE. The "Popular" part is SBI 1408157.

Listed part numbers: SBI 1408157, QUALCAST 308157 and QUALCAST 308158, plus the other parts above.

This table covers the Valve Spring retainers. Read more

One part is listed for the 2011 Honda CR-Z — MELLING VSR729.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

3 Valve Spring Retainer Keeper parts are listed for the 2011 Honda CR-Z, from MELLING, QUALCAST and SBI.

Listed part numbers: MELLING VL1060, QUALCAST 345008 and SBI 1211060.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

14 Valve Stem Seal parts for the 2011 Honda CR-Z come from 10 brands — ELRING, MAHLE / CLEVITE, SBI and 7 other brands. The "Popular" part is APEX AVS1003.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

6 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2011 Honda CR-Z come from 6 brands — DORMAN, GATES, ROSTRA and 3 other brands. The "Popular" part is DORMAN 916987.

The Economy section: 4 options from DORMAN, GATES, ROSTRA and 1 other brand. DORMAN 916987 is listed in this group.

Standard Replacement: 2 parts, from STANDARD MOTOR PRODUCTS and ACKOJA. A representative part number is STANDARD MOTOR PRODUCTS VVT304.

Listed part numbers: DORMAN 916987, GATES VVS323 and ROSTRA 790152, plus the other parts above.

This table covers the Variable Valve Timing (VVT) Solenoid filters. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

5 Variable Valve Timing (VVT) Solenoid Filter parts for the 2011 Honda CR-Z come from 5 brands — FEL-PRO, BECK/ARNLEY, GATES and 2 other brands. The "Popular" part is FEL-PRO ES73072.

Part numbers include FEL-PRO ES73072, BECK/ARNLEY 0396631 and GATES VVS909, among others listed above.

This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2011 Honda CR-Z — ELRING 703510.