2012 Honda CR-Z Engine Parts

This table covers the Camshaft caps. Typical signs include a leak at the neck, a cap that will not hold pressure, or a missing tether. Match the pressure rating or thread in the notes — radiator, reservoir and fuel caps are not interchangeable. Read more

This group shows a single part: AJUSA 00794900.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Camshaft Seal parts are listed for the 2012 Honda CR-Z, from APEX, FEL-PRO, JAPANESE OE and 1 other brand.

This group includes APEX ATC1540, FEL-PRO TCS46212 and JAPANESE OE A6622 and the remaining parts above.

This table covers the Circular / Semi-Circular plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

2 Circular / Semi-Circular Plug parts are listed for the 2012 Honda CR-Z, from APEX and VICTOR REINZ.

Listed part numbers: APEX ACP101 and VICTOR REINZ 711552200.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Connecting Rod Bearing parts for the 2012 Honda CR-Z come from 3 brands — ENGINETECH, MAHLE / CLEVITE and TOPLINE.

Listed part numbers: ENGINETECH BB1065, MAHLE / CLEVITE CB1862A4 and TOPLINE RBH42.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts for the 2012 Honda CR-Z come from 4 brands — AJUSA, APEX, FEL-PRO and 1 other brand.

Part numbers include AJUSA 54172900, APEX ACS1054 and FEL-PRO CS26529, among others listed above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Crankshaft Main Bearing parts are listed for the 2012 Honda CR-Z, from TOPLINE and ENGINETECH.

Listed part numbers: ENGINETECH BC1050, TOPLINE TWH16 and TOPLINE MBH42.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

5 Crankshaft Repair Sleeve parts are listed for the 2012 Honda CR-Z, from SCHAEFFLER, BCA, NATIONAL and 1 other brand. BCA NS99315 carries the "Popular" badge.

Part numbers include BCA NS99315, NATIONAL 99315 and SCHAEFFLER SR3549, among others listed above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

15 Crankshaft Seal parts are listed for the 2012 Honda CR-Z, from APEX, SCHAEFFLER, VICTOR REINZ and 9 other brands. MAHLE / CLEVITE 66986 carries the "Popular" badge.

This table covers the bolts that clamp the cylinder head to the block. Read more

5 Cylinder Head Bolt parts for the 2012 Honda CR-Z come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO ES72449.

This group includes FEL-PRO ES72449, AJUSA 81034300 and APEX AHB164 and the remaining parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Cylinder Head Gasket parts for the 2012 Honda CR-Z come from 5 brands — FEL-PRO, AJUSA, APEX and 2 other brands. The "Popular" part is FEL-PRO 26529PT.

Listed part numbers: FEL-PRO 26529PT, AJUSA 10193300 and APEX AHG167, plus the other parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

7 Cylinder Head Gasket Set parts for the 2012 Honda CR-Z come from 6 brands — FEL-PRO, APEX, AJUSA and 3 other brands. The "Popular" part is APEX AHS1068.

Part numbers include APEX AHS1068, FEL-PRO HS26529PT2 and AJUSA 52284200, among others listed above.

This table covers the Cylinder Head plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

2 Cylinder Head Plug parts are listed for the 2012 Honda CR-Z, from FEL-PRO and MAHLE / CLEVITE.

Part numbers include FEL-PRO 73868 and MAHLE / CLEVITE B32774.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

KAT'S HEATERS supplies both parts for the 2012 Honda CR-Z.

Part numbers include KAT'S HEATERS 11419 and KAT'S HEATERS 28500.

This table covers the Engine covers. Read more

2 Engine Cover parts for the 2012 Honda CR-Z come from TECHPRO.

Listed part numbers: TECHPRO HO1228127 and TECHPRO HO1228128.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Engine Kit Gasket Set parts for the 2012 Honda CR-Z come from 4 brands — AJUSA, APEX, ITM ENGINE COMPONENTS and 1 other brand.

Listed part numbers: AJUSA 50304000, APEX AFS1068 and ITM ENGINE COMPONENTS 0900960, plus the other parts above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

One part is listed for the 2012 Honda CR-Z — TOPLINE EVH42L.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Intake Manifold Gasket parts for the 2012 Honda CR-Z come from 5 brands — MAHLE / CLEVITE, FEL-PRO, APEX and 2 other brands. The "Popular" part is FEL-PRO MS97174.

This group includes FEL-PRO MS97174, APEX AMS1681 and MAHLE / CLEVITE MS19815 and the remaining parts above.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Plenum Gasket parts are listed for the 2012 Honda CR-Z, from FEL-PRO, APEX, MAHLE / CLEVITE and 2 other brands. FEL-PRO MS97178 carries the "Popular" badge.

Part numbers include FEL-PRO MS97178, APEX AMS1680 and MAHLE / CLEVITE MS19816, among others listed above.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

One part is listed for the 2012 Honda CR-Z — TOPLINE IVH42L.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

27 Oil parts are listed for the 2012 Honda CR-Z, from VALVOLINE, MOBIL, LIQUI MOLY and 3 other brands. LIQUI MOLY 2208 carries the "Popular" badge. They are grouped as Full Synthetic and High Mileage (>75,000 Miles), with Full Synthetic the largest group at 20 parts from VALVOLINE, LIQUI MOLY, PENTOSIN and 3 other brands.

This table covers the Oil Dipstick tubes. Read more

One part is listed for the 2012 Honda CR-Z — DORMAN 921097.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts are listed for the 2012 Honda CR-Z, from DORMAN, AGS, REIN and 1 other brand. DORMAN 090033 carries the "Popular" badge.

Listed part numbers: DORMAN 090033, DORMAN 090053 and AGS ODP00007, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts for the 2012 Honda CR-Z come from 5 brands — DORMAN, AJUSA, APEX and 2 other brands. The "Popular" part is DORMAN 095144.

Part numbers include DORMAN 095144, AJUSA 22007400 and APEX ADP1909, among others listed above.

This table covers the caps on the oil filler neck. Read more

4 Oil Filler Cap parts are listed for the 2012 Honda CR-Z, from CALORSTAT, DORMAN, GATES and 1 other brand.

Part numbers include CALORSTAT OC2335, DORMAN 80985 and GATES 31284, among others listed above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

17 Oil Filter parts are listed for the 2012 Honda CR-Z, from BOSCH, VARIOUS MFR, WIX and 11 other brands. WIX 57356XP carries the "Popular" badge.

In the Economy grade, BOSCH, FVP, PRO-TEC and 1 other brand supply 4 parts: the catalog's value-priced group. A representative part number is BOSCH 72226WS.

In the High Performance / Heavy Duty grade, WIX and MOBIL supply 2 parts: grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. A representative part number is WIX 57356XP.

The Standard Replacement section lists 11 options from BOSCH, DENSO, WIX and 8 other brands — built to original-equipment specification. BOSCH 3323 is listed in this group.

This table covers the Oil Filter Support tubes. Read more

This group shows a single part: AUTOTECNICA HA1416938.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Oil Pan Gasket parts are listed for the 2012 Honda CR-Z, from VICTOR REINZ, FEL-PRO, AJUSA and 2 other brands. FEL-PRO OS30837R carries the "Popular" badge.

Listed part numbers: FEL-PRO OS30837R, VICTOR REINZ 703141410 and AJUSA 14090600, plus the other parts above.

This table covers the seals at the Oil Pressure Sender / Switch. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2012 Honda CR-Z — FEL-PRO 73196.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

3 Oil Pump parts are listed for the 2012 Honda CR-Z, from SKP, MELLING and TOPLINE.

Economy: 1 part, from SKP. A representative part number is SKP SKM533.

The Standard Replacement section: 2 options from MELLING and TOPLINE. MELLING M533 is listed in this group.

Part numbers include SKP SKM533, MELLING M533 and TOPLINE OPH42.

This table covers the wear sleeves used to restore a Oil Pump seal surface. Read more

3 Oil Pump Repair Sleeve parts for the 2012 Honda CR-Z come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: BCA NS99157, NATIONAL 99157 and WJB / INMOTION PARTS WS99157.

This table covers the seals at the Oil Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Oil Pump Seal parts for the 2012 Honda CR-Z come from 2 brands — NATIONAL and WJB / INMOTION PARTS.

Listed part numbers: NATIONAL 711005 and WJB / INMOTION PARTS WS711005.

This table covers the gaskets that seal the Oil Strainer. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: AJUSA 01239000.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

This group shows a single part: TOPLINE PAH42L.

This table covers the rings that seal each piston to the cylinder wall. Read more

4 Piston Ring parts for the 2012 Honda CR-Z come from 3 brands — HASTINGS MANUFACTURING, ENGINETECH and TOPLINE.

In the Premium grade, ENGINETECH supplies 1 part: a step above OE specification in materials, tolerances or warranty terms. A representative part number is ENGINETECH S73124.

Standard Replacement: 3 parts, from HASTINGS MANUFACTURING and TOPLINE. A representative part number is HASTINGS MANUFACTURING 2C5253S.

Part numbers include ENGINETECH S73124, HASTINGS MANUFACTURING 2C5253S and HASTINGS MANUFACTURING 2C5253, among others listed above.

This table covers the Thrust washers. Read more

2 Thrust Washer parts are listed for the 2012 Honda CR-Z, from ENGINETECH and ITM ENGINE COMPONENTS.

Listed part numbers: ENGINETECH TW1516 and ITM ENGINE COMPONENTS 1T1001.

This table covers the Timing Cam sprockets. Read more

4 Timing Cam Sprocket parts are listed for the 2012 Honda CR-Z, from CLOYES, FVP, INA and 1 other brand.

This group includes CLOYES S968T and INA ZSS968T and the remaining parts above.

This table covers the timing chains that keep the cams in time with the crank. Read more

4 Timing Chain parts for the 2012 Honda CR-Z come from 4 brands — CLOYES, FVP, INA and 1 other brand.

Listed part numbers: CLOYES C731F and INA ZCC731F, plus the other parts above.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

7 Timing Chain & Component Kit parts are listed for the 2012 Honda CR-Z, from S.A. GEAR, CLOYES, INA and 1 other brand. CLOYES 90731SX carries the "Popular" badge.

Economy: 2 parts, from S.A. GEAR. A representative part number is S.A. GEAR 76329S.

The Standard Replacement section: 5 options from CLOYES, INA and TOPLINE. CLOYES 90731SX is listed in this group.

Listed part numbers: CLOYES 90731SX, S.A. GEAR 76329S and S.A. GEAR 76329, plus the other parts above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

5 Timing Chain Guide / Damper parts for the 2012 Honda CR-Z come from 3 brands — S.A. GEAR, CLOYES and INA. The "Popular" part is S.A. GEAR 91163.

Part numbers include S.A. GEAR 91163, CLOYES 95643 and CLOYES 95642, among others listed above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

4 Timing Chain Tensioner parts are listed for the 2012 Honda CR-Z, from CLOYES, FVP, INA and 1 other brand.

Listed part numbers: CLOYES 95641 and INA ZT95641, plus the other parts above.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2012 Honda CR-Z — MAHLE / CLEVITE JV5159.

This table covers the wear sleeves used to restore a Timing Cover seal surface. Read more

One part is listed for the 2012 Honda CR-Z — SCHAEFFLER SR3487.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

2 Timing Cover Seal parts are listed for the 2012 Honda CR-Z, from MAHLE / CLEVITE and SCHAEFFLER.

This group includes MAHLE / CLEVITE 67932 and SCHAEFFLER SS5126.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

5 Timing Crank Sprocket parts are listed for the 2012 Honda CR-Z, from S.A. GEAR, CLOYES, FVP and 2 other brands. S.A. GEAR S1388 carries the "Popular" badge.

This group includes S.A. GEAR S1388 and CLOYES S967 and the remaining parts above.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

6 Torque Strut Mount parts for the 2012 Honda CR-Z come from 5 brands — DEA / MARMON RIDE CONTROL, SKP, ANCHOR and 2 other brands. The "Popular" part is SKP SKMA4574.

The Economy section: 1 option from SKP. SKP SKMA4574 is listed in this group.

Standard Replacement: 5 parts, from DEA / MARMON RIDE CONTROL, ANCHOR, PIONEER and 1 other brand. A representative part number is DEA / MARMON RIDE CONTROL A4574.

Listed part numbers: SKP SKMA4574, DEA / MARMON RIDE CONTROL A4574 and ANCHOR 9695, plus the other parts above.

This table covers the Valve covers. Read more

This group shows a single part: ACKOJA A260331.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Valve Cover Gasket parts are listed for the 2012 Honda CR-Z, from FEL-PRO, APEX, BECK/ARNLEY and 2 other brands. FEL-PRO VS50785R carries the "Popular" badge.

This group includes FEL-PRO VS50785R, APEX AVC168 and BECK/ARNLEY 0361976 and the remaining parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

5 Valve Guide parts are listed for the 2012 Honda CR-Z, from SBI, QUALCAST and TOPLINE. SBI 1408157 carries the "Popular" badge.

Part numbers include SBI 1408157, QUALCAST 308157 and QUALCAST 308158, among others listed above.

This table covers the Valve Spring retainers. Read more

This group shows a single part: MELLING VSR729.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

3 Valve Spring Retainer Keeper parts for the 2012 Honda CR-Z come from 3 brands — MELLING, QUALCAST and SBI.

Listed part numbers: MELLING VL1060, QUALCAST 345008 and SBI 1211060.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Valve Stem Seal parts are listed for the 2012 Honda CR-Z, from MAHLE / CLEVITE, SBI, APEX and 6 other brands. APEX AVS1003 carries the "Popular" badge.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

6 Variable Valve Timing (VVT) Solenoid / Actuator parts are listed for the 2012 Honda CR-Z, from DORMAN, GATES, ROSTRA and 3 other brands. DORMAN 916987 carries the "Popular" badge.

Economy: 4 parts, from DORMAN, GATES, ROSTRA and 1 other brand. A representative part number is DORMAN 916987.

The Standard Replacement section: 2 options from STANDARD MOTOR PRODUCTS and ACKOJA. STANDARD MOTOR PRODUCTS VVT304 is listed in this group.

This group includes DORMAN 916987, GATES VVS323 and ROSTRA 790152 and the remaining parts above.

This table covers the Variable Valve Timing (VVT) Solenoid filters. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

5 Variable Valve Timing (VVT) Solenoid Filter parts are listed for the 2012 Honda CR-Z, from FEL-PRO, BECK/ARNLEY, GATES and 2 other brands. FEL-PRO ES73072 carries the "Popular" badge.

Listed part numbers: FEL-PRO ES73072, BECK/ARNLEY 0396631 and GATES VVS909, plus the other parts above.