2018 Mitsubishi Outlander Engine Parts

This table covers the chains that drive the balance shafts. Read more

One part is listed for the 2018 Mitsubishi Outlander — S.A. GEAR C1105.

This table covers the guides that keep the balance-shaft chain on its path. Read more

S.A. GEAR supplies both parts for the 2018 Mitsubishi Outlander.

Listed part numbers: S.A. GEAR 71059 and S.A. GEAR 71061.

This table covers the Balance Shaft Chain tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

This group shows a single part: S.A. GEAR 91081.

This table covers the wear sleeves used to restore a Camshaft seal surface. Read more

3 Camshaft Repair Sleeve parts for the 2018 Mitsubishi Outlander come from 3 brands — BCA, NATIONAL and WJB / INMOTION PARTS.

Part numbers include BCA NS99139, NATIONAL 99139 and WJB / INMOTION PARTS WS99139.

This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

7 Camshaft Seal parts for the 2018 Mitsubishi Outlander come from 6 brands — ELRING, FEL-PRO, MAHLE / CLEVITE and 3 other brands. The "Popular" part is FEL-PRO TCS45704.

Part numbers include FEL-PRO TCS45704, MAHLE / CLEVITE 47918 and AJUSA 15013300, among others listed above.

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2018 Mitsubishi Outlander — TOPLINE RBHY11.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

11 Conversion / Lower Gasket Set parts are listed for the 2018 Mitsubishi Outlander, from AJUSA, APEX, FEL-PRO and 4 other brands. ULTRA-POWER CS26410 carries the "Popular" badge.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

2 Crankshaft Main Bearing parts for the 2018 Mitsubishi Outlander come from TOPLINE.

Listed part numbers: TOPLINE TWHY11 and TOPLINE MBHY11.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

4 Crankshaft Repair Sleeve parts for the 2018 Mitsubishi Outlander come from 3 brands — WJB / INMOTION PARTS, BCA and NATIONAL. 3 parts fit every engine; the other 1 is engine-specific.

Listed part numbers: BCA NS99166, NATIONAL 99166 and WJB / INMOTION PARTS WS99166, plus the other parts above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

30 Crankshaft Seal parts for the 2018 Mitsubishi Outlander come from 12 brands — APEX, FEL-PRO, VICTOR REINZ and 9 other brands. The "Popular" part is AJUSA 15052700. A list this long means Crankshaft Seal applications vary by configuration — the notes carry the qualifiers.

This table covers the bolts that clamp the cylinder head to the block. Read more

8 Cylinder Head Bolt parts are listed for the 2018 Mitsubishi Outlander, from AJUSA, TOPLINE, FEL-PRO and 3 other brands. AJUSA 81041900 carries the "Popular" badge.

Listed part numbers: AJUSA 81041900, FEL-PRO ES72472 and AJUSA 81056600, plus the other parts above.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

15 Cylinder Head Gasket parts are listed for the 2018 Mitsubishi Outlander, from APEX, MAHLE / CLEVITE, FEL-PRO and 4 other brands. FEL-PRO 26557PT carries the "Popular" badge.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

12 Cylinder Head Gasket Set parts are listed for the 2018 Mitsubishi Outlander, from AJUSA, FEL-PRO, APEX and 3 other brands. APEX AHS13013 carries the "Popular" badge.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

2 Engine Block Heater parts for the 2018 Mitsubishi Outlander come from KAT'S HEATERS.

Part numbers include KAT'S HEATERS 11812 and KAT'S HEATERS 28812.

This table covers the Engine covers. Read more

TECHPRO supplies the 5 Engine Cover parts for the 2018 Mitsubishi Outlander.

Listed part numbers: TECHPRO MI1228147, TECHPRO MI1228133 and TECHPRO MI1228136, plus the other parts above.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Engine Kit Gasket Set parts are listed for the 2018 Mitsubishi Outlander, from AJUSA and ELRING.

Part numbers include AJUSA 50372000, AJUSA 50574700 and AJUSA 50439500, among others listed above.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

3 Harmonic Balancer parts are listed for the 2018 Mitsubishi Outlander, from ATP, DAYCO and DORMAN.

This group includes ATP 102480, DAYCO PB1772N and DORMAN 594757.

This table covers the Intake manifolds. Typical signs include an exhaust tick, a vacuum leak, or a gasket that has burned through. Replace the gaskets and hardware; a warped flange will leak with a new gasket alone. Read more

This group shows a single part: LARES 33800.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

11 Intake Manifold Gasket parts are listed for the 2018 Mitsubishi Outlander, from FEL-PRO, AJUSA, APEX and 3 other brands. FEL-PRO MS97114 carries the "Popular" badge.

This table covers the gaskets that seal the Intake Plenum. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Intake Plenum Gasket parts for the 2018 Mitsubishi Outlander come from 4 brands — AJUSA, APEX, FEL-PRO and 1 other brand.

Part numbers include AJUSA 01238300, APEX AMS2972 and FEL-PRO MS97076, among others listed above.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Motor Mount parts for the 2018 Mitsubishi Outlander come from 4 brands — ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand.

This group includes ANCHOR 10231, DEA / MARMON RIDE CONTROL A71105 and PIONEER 610001 and the remaining parts above.

This table covers the Motor Mount kits. Read more

This group shows a single part: ANCHOR 301079.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

44 Oil parts for the 2018 Mitsubishi Outlander come from 6 brands — LIQUI MOLY, VALVOLINE, IDEMITSU and 3 other brands. The "Popular" part is LIQUI MOLY 2208. Full Synthetic and High Mileage (>75,000 Miles) are all represented, and Full Synthetic alone accounts for 38 parts.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts for the 2018 Mitsubishi Outlander come from 3 brands — DORMAN, ELRING and SKP. The "Popular" part is DORMAN 090075. 4 parts fit every engine; the other 2 are engine-specific.

Listed part numbers: DORMAN 090075, DORMAN 090053 and DORMAN 092020, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts are listed for the 2018 Mitsubishi Outlander, from DORMAN, AJUSA, APEX and 2 other brands. DORMAN 095141 carries the "Popular" badge. 4 parts fit every engine; the other 1 is engine-specific.

This group includes DORMAN 095141, AJUSA 18001100 and APEX ADP1906 and the remaining parts above.

This table covers the caps on the oil filler neck. Read more

5 Oil Filler Cap parts for the 2018 Mitsubishi Outlander come from 5 brands — GATES, CALORSTAT, MOTORAD and 2 other brands. The "Popular" part is GATES 31118. 1 part fits every engine; the other 4 are engine-specific.

Listed part numbers: GATES 31118, CALORSTAT OC2333 and MOTORAD MO154, plus the other parts above.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

18 Oil Filter parts for the 2018 Mitsubishi Outlander come from 14 brands — BOSCH, VARIOUS MFR, WIX and 11 other brands. The "Popular" part is MOBIL M1110A. 15 parts fit every engine; the other 3 are engine-specific.

The Economy section lists 6 options from BOSCH, FRAM, FVP and 3 other brands — the catalog's value-priced group. BOSCH 72226WS is listed in this group.

The High Performance / Heavy Duty section lists 2 options from MOBIL and WIX — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1110A is listed in this group.

In the Standard Replacement grade, ACKOJA, BOSCH, WIX and 6 other brands supply 10 parts: built to original-equipment specification. A representative part number is BOSCH 3323.

This table covers the oil pans that hold the engine's oil sump. Read more

5 Oil Pan parts are listed for the 2018 Mitsubishi Outlander, from AUTOTECNICA, DORMAN, SKP and 2 other brands.

Part numbers include AUTOTECNICA MI1416200, DORMAN 264312 and SKP SKOP427, among others listed above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Oil Pan Gasket parts for the 2018 Mitsubishi Outlander come from 4 brands — APEX, FEL-PRO, VICTOR REINZ and 1 other brand.

This group includes APEX AOP1170, APEX AOP297 and FEL-PRO OS30824 and the remaining parts above.

This table covers the Timing belts. Typical signs include squeal on cold start, cracked ribs, or glazing. Spin the tensioner and idlers by hand while the belt is off. Read more

6 Timing Belt parts are listed for the 2018 Mitsubishi Outlander, from CONTINENTAL, DAYCO, GATES and 2 other brands. DAYCO 95339 carries the "Popular" badge.

Economy: 1 part, from CONTINENTAL. A representative part number is CONTINENTAL CD339.

The Standard Replacement section: 5 options from DAYCO, GATES, ACDELCO and 2 other brands. DAYCO 95339 is listed in this group.

Part numbers include DAYCO 95339, CONTINENTAL CD339 and GATES T339, among others listed above.

This table covers the Timing Belt & component kits. Read more

8 Timing Belt & Component Kit parts for the 2018 Mitsubishi Outlander come from 5 brands — GMB, CONTINENTAL, DAYCO and 2 other brands. The "Popular" part is DAYCO WP339K1A.

This group includes DAYCO WP339K1A, CONTINENTAL CK339LK1 and CONTINENTAL TB339K1 and the remaining parts above.

This table covers the Timing Belt pulleys. Typical signs include a growl or chirp that follows engine speed, or a pulley that will not spin freely by hand. Spin each pulley with the belt off. Roughness or play means replace it with the belt. Read more

This group shows a single part: GMB 4481100.

This table covers the Timing Belt tensioners. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

3 Timing Belt Tensioner parts for the 2018 Mitsubishi Outlander come from 3 brands — AISIN, DAYCO and GATES.

This group includes AISIN BTM501, DAYCO 85028 and GATES T43189.

This table covers the timing chains that keep the cams in time with the crank. Read more

2 Timing Chain parts are listed for the 2018 Mitsubishi Outlander, from MELLING and S.A. GEAR.

Listed part numbers: MELLING 900C and S.A. GEAR C1248.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

This group shows a single part: S.A. GEAR 76470S.

This table covers the guides and dampers that keep the timing chain on its path. Read more

3 Timing Chain Guide / Damper parts are listed for the 2018 Mitsubishi Outlander, from S.A. GEAR and MELLING.

Part numbers include MELLING BG5558, S.A. GEAR 71321 and S.A. GEAR 91438.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

4 Timing Chain Tensioner parts for the 2018 Mitsubishi Outlander come from 4 brands — CLOYES, FVP, MELLING and 1 other brand.

Listed part numbers: CLOYES 95559 and MELLING BT5559, plus the other parts above.

This table covers the Timing idlers. Typical signs include a chirp that follows engine speed, or an idler that feels rough or has play. Replace a noisy idler with the belt — the labor is already paid for. Read more

2 Timing Idler parts for the 2018 Mitsubishi Outlander come from 2 brands — GATES and INA.

Listed part numbers: GATES T42308 and INA FP0646.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Torque Strut Mount parts are listed for the 2018 Mitsubishi Outlander, from ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand. 3 parts fit every engine; the other 1 is engine-specific.

This group includes ANCHOR 10217, DEA / MARMON RIDE CONTROL A4657 and PIONEER 634657 and the remaining parts above.