2013 Toyota Sequoia Automatic Transmission Parts

This table covers the Boost valves. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

2 Boost Valve parts are listed for the 2013 Toyota Sequoia, from SONNAX and TRANSGO.

Listed part numbers: SONNAX A750LB1 and TRANSGO A750BOOST.

This table covers the vents on a transmission or axle housing. Read more

DORMAN supplies both parts for the 2013 Toyota Sequoia.

Part numbers include DORMAN 924284 and DORMAN 924262.

This table covers the clutch-plate packs inside the transmission or transfer case. Read more

4 Clutch Plate Pack parts for the 2013 Toyota Sequoia come from RAYBESTOS POWERTRAIN.

In the Friction Plate Pack grade, RAYBESTOS POWERTRAIN supplies 3 parts: grouped under the catalog's "Friction Plate Pack" designation — the notes column spells out what sets them apart. A representative part number is RAYBESTOS POWERTRAIN RGPZ023.

The Steel Plate Pack section lists 1 option from RAYBESTOS POWERTRAIN — grouped under the catalog's "Steel Plate Pack" designation — the notes column spells out what sets them apart. RAYBESTOS POWERTRAIN STMTOYTA55 is listed in this group.

This group includes RAYBESTOS POWERTRAIN RGPZ023, RAYBESTOS POWERTRAIN FRMTOYTA55 and RAYBESTOS POWERTRAIN RCP96261 and the remaining parts above.

This table covers the End plugs. Typical signs include a leak at the drain or glow-plug hole, or a plug that has rounded off. Replace the crush washer and torque to the spec in the notes. Read more

One part is listed for the 2013 Toyota Sequoia — TRANSGO 960VBPLGS.

This table covers the seals at the Extension Housing. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

5 Extension Housing Seal parts are listed for the 2013 Toyota Sequoia, from NATIONAL, WJB / INMOTION PARTS and BCA. NATIONAL 710689 carries the "Popular" badge.

Part numbers include NATIONAL 710689, BCA NS710689 and NATIONAL 710779, among others listed above.

This table covers the replacement filters for this application — the table heading and notes say which circuit. Typical signs include restricted flow — long cranking, weak airflow, or dirty fluid after a short interval. Seat the new filter so it cannot bypass, and use the grade the notes call for. Read more

5 Filter parts for the 2013 Toyota Sequoia come from 5 brands — VARIOUS MFR, ATP, BECK/ARNLEY and 2 other brands. The "Popular" part is VARIOUS MFR PT99109.

The Economy section lists 1 option from VARIOUS MFR — the catalog's value-priced group. VARIOUS MFR PT99109 is listed in this group.

In the Standard Replacement grade, ATP, BECK/ARNLEY, RAYBESTOS POWERTRAIN and 1 other brand supply 4 parts: built to original-equipment specification. A representative part number is ATP B332.

Part numbers include VARIOUS MFR PT99109, ATP B332 and BECK/ARNLEY 0440396, among others listed above.

This table covers the heat exchangers that cool transmission fluid. Typical signs include fluid that overheats, a leak at the cooler fittings, or milky fluid that says coolant and ATF have mixed. Flush the lines when you replace a cooler. Cross-contamination is how a small leak becomes a transmission job. Read more

2 Fluid Cooler parts for the 2013 Toyota Sequoia come from 2 brands — AUTOTECNICA and DORMAN.

This group includes AUTOTECNICA TY1220027 and DORMAN 918678.

This table covers the gaskets that seal the Fluid Pan. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

4 Fluid Pan Gasket parts for the 2013 Toyota Sequoia come from 4 brands — FEL-PRO, MAHLE / CLEVITE, VAICO and 1 other brand.

This group includes FEL-PRO TOS18760, MAHLE / CLEVITE W33242 and VAICO V700733 and the remaining parts above.

This table covers the seals at the Fluid Pump. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2013 Toyota Sequoia — WJB / INMOTION PARTS WS710778.

This table covers the seals at the Manual Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

3 Manual Shaft Seal parts are listed for the 2013 Toyota Sequoia, from BCA, NATIONAL and WJB / INMOTION PARTS.

This group includes BCA NS221207, NATIONAL 221207 and WJB / INMOTION PARTS WS221207.

This table covers the seals at the Output Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

This group shows a single part: SKF 20001.

This table covers the Pressure Control (EPC) solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

4 Pressure Control (EPC) Solenoid parts for the 2013 Toyota Sequoia come from 3 brands — ROSTRA, STANDARD MOTOR PRODUCTS and WELLS.

This group includes ROSTRA 520590, ROSTRA 520591 and STANDARD MOTOR PRODUCTS TCS126 and the remaining parts above.

This table covers the Shift Improvement kits. Read more

This group shows a single part: TRANSGO SKA750WTA.

This table covers the Shift Linkage bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2013 Toyota Sequoia — DORMAN 14103.

This table covers the seals at the Shift Shaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

One part is listed for the 2013 Toyota Sequoia — SCHAEFFLER SS2111.

This table covers the Shift solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

11 Shift Solenoid parts are listed for the 2013 Toyota Sequoia, from ROSTRA, BECK/ARNLEY, STANDARD MOTOR PRODUCTS and 1 other brand. ROSTRA 520587 carries the "Popular" badge.

This table covers the Torque converters. Typical signs include a sulfur smell, rattling substrate, or an efficiency code. Confirm CARB vs Federal certification in the notes before ordering. Read more

This group shows a single part: TC REMANUFACTURING TO92.

This table covers the Torque Converter Clutch solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

3 Torque Converter Clutch Solenoid parts for the 2013 Toyota Sequoia come from 3 brands — BECK/ARNLEY, STANDARD MOTOR PRODUCTS and WELLS.

This group includes BECK/ARNLEY 0470023, STANDARD MOTOR PRODUCTS TCS332 and WELLS 2N1423.

This table covers the automatic-transmission fluids specified for this gearbox. Typical signs include harsh or delayed shifts, fluid that smells burnt, or a shudder at light throttle. Use exactly the specification in the notes. Automatic transmissions are unforgiving of the wrong fluid. Read more

18 Transmission Fluid parts for the 2013 Toyota Sequoia come from 9 brands — VALVOLINE, LIQUI MOLY, PENTOSIN and 6 other brands. The "Popular" part is ACDELCO 109243.

In the ATF 64 grade, PENTOSIN supplies 2 parts: grouped under the catalog's "ATF 64" designation — the notes column spells out what sets them apart. A representative part number is PENTOSIN 1058113.

The Dexron section lists 1 option from ACDELCO — grouped under the catalog's "Dexron" designation — the notes column spells out what sets them apart. ACDELCO 109243 is listed in this group.

The Multi-Vehicle section lists 11 options from VALVOLINE, LIQUI MOLY, LUCAS OIL and 2 other brands — grouped under the catalog's "Multi-Vehicle" designation — the notes column spells out what sets them apart. MOBIL 126505 is listed in this group.

The World Standard (WS) section lists 3 options from IDEMITSU and AISIN — grouped under the catalog's "World Standard (WS)" designation — the notes column spells out what sets them apart. AISIN ATF0WS is listed in this group.

1 further part sits outside the graded sections, with the same engine-level match.

This table covers the conditioners and additives used with this transmission fluid. Read more

8 Transmission Fluid Additive parts for the 2013 Toyota Sequoia come from LUBEGARD. The "Popular" part is LUBEGARD 19610.

This group includes LUBEGARD 19610, LUBEGARD 60902 and LUBEGARD 19689 and the remaining parts above.

This table covers the mounts that hold the transmission to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

9 Transmission Mount parts are listed for the 2013 Toyota Sequoia, from ULTRA-POWER, ANCHOR, DEA / MARMON RIDE CONTROL and 2 other brands. ANCHOR 9522 carries the "Popular" badge.

Economy: 2 parts, from ULTRA-POWER. A representative part number is ULTRA-POWER A62095.

The Standard Replacement section: 7 options from ANCHOR, DEA / MARMON RIDE CONTROL, WESTAR and 1 other brand. ANCHOR 9522 is listed in this group.

Listed part numbers: ANCHOR 9522, ULTRA-POWER A62095 and ULTRA-POWER A42016, plus the other parts above.

This table covers the Transmission Mount bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

One part is listed for the 2013 Toyota Sequoia — ENERGY SUSPENSION 81110.