2013 Toyota Sienna Engine Parts

This table covers the bearings in the connecting-rod big ends. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

One part is listed for the 2013 Toyota Sienna — TOPLINE RBTO56.

This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Conversion / Lower Gasket Set parts are listed for the 2013 Toyota Sienna, from AJUSA, FEL-PRO, ITM ENGINE COMPONENTS and 1 other brand.

Listed part numbers: AJUSA 54185000, FEL-PRO CS26562 and ITM ENGINE COMPONENTS 0922711, plus the other parts above.

This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly. Read more

3 Crankshaft Main Bearing parts for the 2013 Toyota Sienna come from 2 brands — TOPLINE and MAHLE / CLEVITE.

Listed part numbers: MAHLE / CLEVITE MS2376A, TOPLINE TWTO56 and TOPLINE MBTO56.

This table covers the sleeves used to restore a grooved crankshaft seal surface. Read more

4 Crankshaft Repair Sleeve parts for the 2013 Toyota Sienna come from 3 brands — WJB / INMOTION PARTS, BCA and NATIONAL.

Part numbers include BCA NS99166, NATIONAL 99166 and WJB / INMOTION PARTS WS99166, among others listed above.

This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

15 Crankshaft Seal parts for the 2013 Toyota Sienna come from 8 brands — ELRING, VICTOR REINZ, FEL-PRO and 5 other brands. The "Popular" part is FEL-PRO BS40741.

This table covers the bolts that clamp the cylinder head to the block. Read more

5 Cylinder Head Bolt parts are listed for the 2013 Toyota Sienna, from FEL-PRO, AJUSA, MAHLE / CLEVITE and 2 other brands. FEL-PRO ES722492 carries the "Popular" badge.

Listed part numbers: FEL-PRO ES722492, AJUSA 81042100 and MAHLE / CLEVITE GS33754, plus the other parts above.

This table covers the Cylinder Head Bolt washers. Read more

2 Cylinder Head Bolt Washer parts are listed for the 2013 Toyota Sienna, from FEL-PRO and VICTOR REINZ.

This group includes FEL-PRO ES72899 and VICTOR REINZ 161001001.

This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

6 Cylinder Head Gasket parts are listed for the 2013 Toyota Sienna, from FEL-PRO, MAHLE / CLEVITE, AJUSA and 3 other brands. FEL-PRO 26562PT carries the "Popular" badge.

This group includes FEL-PRO 26562PT, MAHLE / CLEVITE 54994 and AJUSA 10202100 and the remaining parts above.

This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

8 Cylinder Head Gasket Set parts are listed for the 2013 Toyota Sienna, from FEL-PRO, AJUSA, ITM ENGINE COMPONENTS and 3 other brands. FEL-PRO HS26562PT carries the "Popular" badge.

Listed part numbers: FEL-PRO HS26562PT, ITM ENGINE COMPONENTS 0911846 and AJUSA 52357100, plus the other parts above.

This table covers the block heaters that warm the coolant or oil in cold weather. Read more

2 Engine Block Heater parts for the 2013 Toyota Sienna come from KAT'S HEATERS.

This group includes KAT'S HEATERS 11813 and KAT'S HEATERS 28813.

This table covers the Engine covers. Read more

5 Engine Cover parts are listed for the 2013 Toyota Sienna, from TECHPRO and VARIOUS MFR. TECHPRO TO1228174 carries the "Popular" badge.

Listed part numbers: TECHPRO TO1228174, TECHPRO LX1228131 and TECHPRO LX1228166, plus the other parts above.

This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration. Read more

4 Engine Kit Gasket Set parts are listed for the 2013 Toyota Sienna, from AJUSA, TOPLINE and VICTOR REINZ.

Part numbers include AJUSA 50322800, AJUSA 50323500 and TOPLINE CGSTO56, among others listed above.

This table covers the exhaust valves that let combustion gas out of the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: TOPLINE EVTO56.

This table covers the crankshaft pulleys / harmonic balancers at the front of the engine. Read more

4 Harmonic Balancer parts are listed for the 2013 Toyota Sienna, from SKP, ATP, DAYCO and 1 other brand.

In the Economy grade, SKP supplies 1 part: the catalog's value-priced group. A representative part number is SKP SK594403.

The Standard Replacement section lists 3 options from ATP, DAYCO and PIONEER — built to original-equipment specification. ATP 102346 is listed in this group.

Listed part numbers: SKP SK594403, ATP 102346 and DAYCO PB1719N, plus the other parts above.

This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Intake Manifold Gasket parts are listed for the 2013 Toyota Sienna, from FEL-PRO, AJUSA, ELRING and 2 other brands. FEL-PRO MS97232 carries the "Popular" badge.

Part numbers include FEL-PRO MS97232, AJUSA 13244500 and ELRING 179680, among others listed above.

This table covers the Intake Manifold Runner Control Valve solenoids. Typical signs include a harsh or missing shift, or a code for this solenoid circuit. Check resistance and the connector before dropping the pan for a solenoid. Read more

One part is listed for the 2013 Toyota Sienna — STANDARD MOTOR PRODUCTS IMRC15.

This table covers the intake valves that let air (and fuel, on port-injected engines) into the cylinder. Typical signs include a circuit that will not hold, a whistle, or a code for this valve. A stuck valve is often debris. Clean the ports before installing the new one. Read more

This group shows a single part: TOPLINE IVTO56.

This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

9 Motor Mount parts for the 2013 Toyota Sienna come from 6 brands — ANCHOR, WESTAR, PIONEER and 3 other brands. The "Popular" part is ANCHOR 9694.

The Economy section: 1 option from SKP. SKP SKM9694 is listed in this group.

Standard Replacement: 8 parts, from ANCHOR, WESTAR, PIONEER and 2 other brands. A representative part number is ANCHOR 9694.

Listed part numbers: ANCHOR 9694, SKP SKM9694 and WESTAR EM5900, plus the other parts above.

This table covers the Motor Mount kits. Read more

This group shows a single part: ANCHOR 300420.

This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable. Read more

14 Oil parts for the 2013 Toyota Sienna come from 3 brands — MOBIL, VALVOLINE and PENTOSIN. The "Popular" part is MOBIL 124184.

The Full Synthetic section lists 9 options from PENTOSIN, MOBIL and VALVOLINE — full-synthetic oils. MOBIL 124184 is listed in this group.

In the High Mileage (>75,000 Miles) grade, MOBIL and VALVOLINE supply 5 parts: oils grouped for high-mileage engines. A representative part number is MOBIL 125203.

This table covers the Oil Dipstick tubes. Read more

This group shows a single part: DORMAN 921135.

This table covers the drain plugs in the oil pan. Read more

6 Oil Drain Plug parts for the 2013 Toyota Sienna come from 4 brands — DORMAN, ELRING, AGS and 1 other brand. The "Popular" part is DORMAN 090038.

Listed part numbers: DORMAN 090038, DORMAN 090049 and AGS ODP00011, plus the other parts above.

This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

5 Oil Drain Plug Gasket parts are listed for the 2013 Toyota Sienna, from DORMAN, AJUSA, ELRING and 2 other brands. DORMAN 095156 carries the "Popular" badge.

Listed part numbers: DORMAN 095156, AJUSA 22005800 and ELRING 473500, plus the other parts above.

This table covers the caps on the oil filler neck. Read more

6 Oil Filler Cap parts for the 2013 Toyota Sienna come from 6 brands — DORMAN, STANT, CALORSTAT and 3 other brands. The "Popular" part is DORMAN 84111.

This group includes DORMAN 84111, STANT 10135 and CALORSTAT OC2329 and the remaining parts above.

This table covers the gaskets that seal the Oil Filler Cap. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

One part is listed for the 2013 Toyota Sienna — AJUSA 00519100.

This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive. Read more

11 Oil Filter parts for the 2013 Toyota Sienna come from 9 brands — VARIOUS MFR, WIX, PRO-TEC and 6 other brands. The "Popular" part is PRO-TEC PXL57047.

The Economy section: 4 options from PRO-TEC, BOSCH, FVP and 1 other brand. PRO-TEC PXL57047 is listed in this group.

The High Performance / Heavy Duty section lists 2 options from WIX and MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. WIX 57047XP is listed in this group.

Standard Replacement: 5 parts, from WIX, ACDELCO, FEL-PRO and 2 other brands. A representative part number is WIX 57047.

This table covers the Oil Filter covers. Read more

4 Oil Filter Cover parts are listed for the 2013 Toyota Sienna, from MOTORAD, AUTOTECNICA and DORMAN.

This group includes AUTOTECNICA TY1420831, DORMAN 917016 and MOTORAD MO300 and the remaining parts above.

This table covers the oil pans that hold the engine's oil sump. Read more

8 Oil Pan parts are listed for the 2013 Toyota Sienna, from AUTOTECNICA, SKP, ACKOJA and 5 other brands. AUTOTECNICA TY1414689 carries the "Popular" badge.

Listed part numbers: AUTOTECNICA TY1414689, SKP SK264474 and ACKOJA A700432, plus the other parts above.

This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

3 Oil Pan Gasket parts for the 2013 Toyota Sienna come from 3 brands — FEL-PRO, MAHLE / CLEVITE and VICTOR REINZ.

This group includes FEL-PRO OS30842, MAHLE / CLEVITE OS32456 and VICTOR REINZ 711550300.

This table covers the Oil pumps. Typical signs include noise from the pump, no pressure, or fluid that never arrives at the outlet. Prime or fill the pump as the notes require. A dry start is a common way to kill a new unit. Read more

2 Oil Pump parts for the 2013 Toyota Sienna come from 2 brands — ITM ENGINE COMPONENTS and TOPLINE.

This group includes ITM ENGINE COMPONENTS 85000 and TOPLINE OPTO56.

This table covers the pistons that travel in each cylinder. Typical signs include knock, blow-by, or a cylinder that will not hold compression. Piston work is a short-block job. Match bore, pin and ring pack in the notes — not the photo. Read more

One part is listed for the 2013 Toyota Sienna — TOPLINE PATO57.

This table covers the Piston Pin bushings. Typical signs include a clunk over bumps, or a torn or walked-out bushing you can see. Press the new bushing square. A cocked bushing will tear in a few thousand miles. Read more

This group shows a single part: TOPLINE PBD34.

This table covers the rings that seal each piston to the cylinder wall. Read more

One part is listed for the 2013 Toyota Sienna — TOPLINE RSTO56.

This table covers the Thrust washers. Read more

This group shows a single part: MAHLE / CLEVITE TW742S.

This table covers the timing chains that keep the cams in time with the crank. Read more

3 Timing Chain parts are listed for the 2013 Toyota Sienna, from AISIN, CLOYES and FVP.

Listed part numbers: AISIN ETCT003 and CLOYES 94313, plus the other parts above.

This table covers kits that group a timing chain with the related tensioners and guides. Read more

5 Timing Chain & Component Kit parts for the 2013 Toyota Sienna come from 4 brands — CLOYES, GATES, ITM ENGINE COMPONENTS and 1 other brand. The "Popular" part is CLOYES 94313S.

The Economy section: 2 options from GATES and ITM ENGINE COMPONENTS. GATES CHK148 is listed in this group.

Standard Replacement: 3 parts, from CLOYES and TOPLINE. A representative part number is CLOYES 94313S.

Part numbers include CLOYES 94313S, GATES CHK148 and ITM ENGINE COMPONENTS 05392301, among others listed above.

This table covers the guides and dampers that keep the timing chain on its path. Read more

6 Timing Chain Guide / Damper parts are listed for the 2013 Toyota Sienna, from CLOYES and FVP. CLOYES 95798 carries the "Popular" badge.

Part numbers include CLOYES 95798, CLOYES 95795 and CLOYES 95796, among others listed above.

This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage. Read more

2 Timing Chain Tensioner parts for the 2013 Toyota Sienna come from 2 brands — CLOYES and FVP.

This group includes CLOYES 95797 and the remaining parts above.

This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

This group shows a single part: MAHLE / CLEVITE JV5185.

This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

4 Timing Cover Seal parts for the 2013 Toyota Sienna come from 4 brands — MAHLE / CLEVITE, SCHAEFFLER, SKF and 1 other brand.

This group includes MAHLE / CLEVITE 68018, SCHAEFFLER SS6638 and SKF 16538A and the remaining parts above.

This table covers the crankshaft sprockets that drive the timing chain or belt. Read more

2 Timing Crank Sprocket parts for the 2013 Toyota Sienna come from 2 brands — CLOYES and FVP.

This group includes CLOYES S1037 and the remaining parts above.

This table covers the Torque Strut mounts. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes. Read more

4 Torque Strut Mount parts are listed for the 2013 Toyota Sienna, from ANCHOR, DEA / MARMON RIDE CONTROL, PIONEER and 1 other brand.

Listed part numbers: ANCHOR 9746, DEA / MARMON RIDE CONTROL A42010 and PIONEER 639737, plus the other parts above.

This table covers the Valve covers. Read more

One part is listed for the 2013 Toyota Sienna — ACKOJA A700621.

This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for. Read more

7 Valve Cover Gasket parts for the 2013 Toyota Sienna come from 5 brands — ELRING, VICTOR REINZ, FEL-PRO and 2 other brands. The "Popular" part is FEL-PRO VS50825R.

Listed part numbers: FEL-PRO VS50825R, MAHLE / CLEVITE VS50721 and AJUSA 56051300, plus the other parts above.

This table covers the pressed-in bronze and cast-iron guides that align valve stems. Typical signs include oil smoke on startup, a guide that has gone oval, or a valve that no longer seats quietly. Guides are a machine-shop fit. Confirm stem diameter in the notes before ordering. Read more

This group shows a single part: QUALCAST 303134.

This table covers the lifters / tappets that transfer cam motion to the valves. Read more

3 Valve Lifter parts for the 2013 Toyota Sienna come from 2 brands — TOPLINE and QUALCAST.

Part numbers include QUALCAST 367082, TOPLINE A2319 and TOPLINE LIFTO55P.

This table covers the keepers that lock each valve-spring retainer to the stem. Read more

2 Valve Spring Retainer Keeper parts are listed for the 2013 Toyota Sienna, from MELLING and QUALCAST.

Part numbers include MELLING VL1100 and QUALCAST 345023.

This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again. Read more

11 Valve Stem Seal parts for the 2013 Toyota Sienna come from 6 brands — ELRING, MAHLE / CLEVITE, QUALCAST and 3 other brands. The "Popular" part is FEL-PRO SS728781.

This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same. Read more

10 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2013 Toyota Sienna come from 9 brands — CLOYES, SKP, DORMAN and 6 other brands. The "Popular" part is SKP SK917235.

The Economy section: 5 options from SKP, DORMAN, HOLSTEIN and 2 other brands. SKP SK917235 is listed in this group.

Standard Replacement: 5 parts, from CLOYES, STANDARD MOTOR PRODUCTS, ACKOJA and 1 other brand. A representative part number is STANDARD MOTOR PRODUCTS VVT201.

This table covers the cam phaser sprockets used by the variable-valve-timing system. Read more

4 Variable Valve Timing (VVT) Sprocket parts for the 2013 Toyota Sienna come from 3 brands — CLOYES, SPECTRA PREMIUM and WELLS.

The Economy section: 1 option from SPECTRA PREMIUM. SPECTRA PREMIUM CSP1019 is listed in this group.

Standard Replacement: 3 parts, from CLOYES and WELLS. A representative part number is CLOYES VC140.

This group includes SPECTRA PREMIUM CSP1019, CLOYES VC140 and CLOYES VC159 and the remaining parts above.

This table covers the Variable Valve Timing (VVT) Sprocket bolts. Read more

One part is listed for the 2013 Toyota Sienna — CLOYES VCB103.