196 Engine parts are listed for the 2021 BMW X7, in 48 part types, covering both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. Each one has a brand, a manufacturer part number and notes that say where it fits.
The engine on the 2021 BMW X7 covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components. The largest groups are Oil Filter (24 parts), Variable Valve Timing (VVT) Solenoid / Actuator (16 parts) and Crankshaft Seal (12 parts). The other 45 part types cover the remaining 144 parts.
The 2021 BMW X7 was sold with both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. 9 parts fit every engine; the other 187 are engine-specific. Each part shows which engine(s) it fits.
46 brands supply engine parts for the 2021 BMW X7, led by AJUSA (44 parts), REIN (16 parts) and VICTOR REINZ (14 parts), plus 43 more brands. Quality grades include Standard Replacement, Economy and High Performance / Heavy Duty.
A "Popular" badge means the source catalog flagged the part as frequently chosen for the 2021 BMW X7. 25 parts have it, including MAHLE / CLEVITE 68102 (Crankshaft Seal) and ELRING 793491 (Cylinder Head Gasket). Each part number opens a page with every vehicle that part fits.
Camshaft Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 4.4L V8 Turbocharged | TCS46149 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front | View on Amazon |
This table covers the seals at each camshaft end. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
This group shows a single part: FEL-PRO TCS46149.
Conversion / Lower Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 54302500 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 54304500 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers lower / conversion gasket sets for oil-pan and related joints. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
AJUSA supplies both parts for the 2021 BMW X7.
Part numbers include AJUSA 54302500 and AJUSA 54304500.
Crankshaft Main Bearing
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| KING ENGINE BEARINGS Fits: 3.0L L6 Turbocharged | MB7779SM | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | BI-Metal (strengthened aluminum)Set | View on Amazon |
| KING ENGINE BEARINGS Fits: 3.0L L6 Turbocharged | MB7779MC | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | BI-Metal (strengthened aluminum)Set | View on Amazon |
This table covers the main bearings that support the crankshaft in the block. Typical signs include a growl that rises with speed, or play in the shaft or hub. Set preload the way the notes specify. A dry or crushed bearing fails quickly.
2 Crankshaft Main Bearing parts for the 2021 BMW X7 come from KING ENGINE BEARINGS.
Listed part numbers: KING ENGINE BEARINGS MB7779SM and KING ENGINE BEARINGS MB7779MC.
Crankshaft Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| MAHLE / CLEVITE Popular Fits: 3.0L L6 Turbocharged | 68102 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | PTFE (Polytetrafluoroethylene) | View on Amazon |
| VICTOR REINZ Popular Fits: 3.0L L6 Turbocharged | 812941200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Material: ACM (Polyacrylate) | View on Amazon |
| VICTOR REINZ Popular Fits: 4.4L V8 Turbocharged | 813939100 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front | View on Amazon |
| VICTOR REINZ Popular Fits: 4.4L V8 Turbocharged | 811040300 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Rearwith Flange | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 15075200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | FrontClockwise | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 15107900 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RearCounter Clockwise | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 61002100 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | FrontClockwise | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 71010700 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Rear | View on Amazon |
| FEL-PRO Fits: 4.4L V8 Turbocharged | BS40780 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Rear | View on Amazon |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | 68123 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | PTFE (Polytetrafluoroethylene) | View on Amazon |
| MAHLE / CLEVITE Fits: 4.4L V8 Turbocharged | 68040 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RubberIncludes Flange | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 811044800 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RearReplaces OE Part Number(s) 11148602594 | View on Amazon |
This table covers the front and rear seals that keep oil in at the crankshaft. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
12 Crankshaft Seal parts for the 2021 BMW X7 come from 4 brands — VICTOR REINZ, AJUSA, MAHLE / CLEVITE and 1 other brand. The "Popular" part is MAHLE / CLEVITE 68102.
Cylinder Head Bolt
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 81069200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 81061000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 141226103 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Set | View on Amazon |
This table covers the bolts that clamp the cylinder head to the block.
3 Cylinder Head Bolt parts are listed for the 2021 BMW X7, from AJUSA and VICTOR REINZ.
Part numbers include AJUSA 81069200, AJUSA 81061000 and VICTOR REINZ 141226103.
Cylinder Head Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ELRING Popular Fits: 3.0L L6 Turbocharged | 793491 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Installed Thickness [MM]: 0,81Material: Multi-Layer Steel (MLS) | View on Amazon |
| ELRING Popular Fits: 3.0L L6 Turbocharged | 739501 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Installed Thickness [MM]: 1,11Material: Multi-Layer Steel (MLS) | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 10248900 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Multi Layered Steel | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 10248910 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Multi Layered Steel | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 10249900 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Multi Layered SteelThickness: 1 MM | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 10249910 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Multi Layered SteelThickness: 0.7 MM | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 52607100 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Right | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 52607200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Left | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 611084400 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | 0.80mm Thickwith Engine Code B58B30C | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 611084410 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | 1.10mm Thickwith Engine Code B58B30C | View on Amazon |
This table covers the head gaskets that seal the block to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
10 Cylinder Head Gasket parts are listed for the 2021 BMW X7, from AJUSA, ELRING and VICTOR REINZ. ELRING 793491 carries the "Popular" badge.
Cylinder Head Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 52561500 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 52607000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Complete Set | View on Amazon |
This table covers multi-piece gasket sets for a cylinder-head job. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
AJUSA supplies both parts for the 2021 BMW X7.
Part numbers include AJUSA 52561500 and AJUSA 52607000.
Engine Cover
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| TECHPRO Fits: all 2021 X7 engines | BM1228191 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front LowerG05 | View on Amazon |
This table covers the Engine covers.
One part is listed for the 2021 BMW X7 — TECHPRO BM1228191.
Engine Kit Gasket Set
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 50515000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 50549100 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers full gasket kits covering the joints opened in an engine rebuild. Typical signs include the leaks that sent the engine or gearbox to the bench. Use every gasket the set is meant for that opening — leftover unused pieces usually belong to another configuration.
AJUSA supplies both parts for the 2021 BMW X7.
Part numbers include AJUSA 50515000 and AJUSA 50549100.
Harmonic Balancer Bolt
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Fits: 3.0L L6 Turbocharged | HWB0074 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | 10 x 65mm | View on Amazon |
This table covers the Harmonic Balancer bolts.
This group shows a single part: REIN HWB0074.
Intake Manifold Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 13313000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 13314000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | MS20642 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | SetMolded Rubber | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 711737500 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the gaskets between the intake manifold and the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
4 Intake Manifold Gasket parts are listed for the 2021 BMW X7, from AJUSA, MAHLE / CLEVITE and VICTOR REINZ.
Part numbers include AJUSA 13313000, AJUSA 13314000 and MAHLE / CLEVITE MS20642, among others listed above.
Motor Mount
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ANCHOR Popular Fits: all 2021 X7 engines | 10258 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front RightHydraulic | View on Amazon |
| ANCHOR Popular Fits: 3.0L L6 Turbocharged | 10260 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front LeftHydraulic | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 3.0L L6 Turbocharged | A70079 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Left | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 3.0L L6 Turbocharged | A70084 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Right | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 4.4L V8 Turbocharged | A70085 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Left | View on Amazon |
| DEA / MARMON RIDE CONTROL Fits: 4.4L V8 Turbocharged | A70086 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Right | View on Amazon |
| PIONEER Fits: all 2021 X7 engines | 610258 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front Right | View on Amazon |
| PIONEER Fits: 3.0L L6 Turbocharged | 611260 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front Left | View on Amazon |
| WESTAR Fits: 3.0L L6 Turbocharged | EM7560 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Right | View on Amazon |
This table covers the mounts that hold the engine to the chassis. Typical signs include a clunk on takeoff, a vibration at idle, or a separated rubber insert. Support the powertrain before unbolting a mount, and torque the fasteners in the notes.
9 Motor Mount parts for the 2021 BMW X7 come from 4 brands — DEA / MARMON RIDE CONTROL, ANCHOR, PIONEER and 1 other brand. The "Popular" part is ANCHOR 10258. 2 parts fit every engine; the other 7 are engine-specific.
Listed part numbers: ANCHOR 10258, ANCHOR 10260 and DEA / MARMON RIDE CONTROL A70079, plus the other parts above.
Oil
Summary: Notes list SAE 0W-20, SAE 0W-30 and SAE 5W-30. Confirm the engine and the weight on the filler cap before you buy. Replacement brands in this table include LIQUI MOLY, VALVOLINE and PENTOSIN.
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| LIQUI MOLY Popular Fits: 3.0L L6 Turbocharged | 22044 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Top Tec 6600 0W-201 Liter | View on Amazon |
| LIQUI MOLY Popular Fits: 3.0L L6 Turbocharged | 22046 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Top Tec 6600 0W-205 Liter | View on Amazon |
| MOBIL Popular Fits: 4.4L V8 Turbocharged | 127568 | 🇺🇸 US | ESP 5W30 1 Quart | View on Amazon |
| VALVOLINE Popular Fits: 4.4L V8 Turbocharged | 787301 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | European Vehicle Full Synthetic SAE 5W-301 Quart | View on Amazon |
| LIQUI MOLY Fits: 3.0L L6 Turbocharged | 22048 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Top Tec 6600 0W-2020 Liter | View on Amazon |
| LIQUI MOLY Fits: 4.4L V8 Turbocharged | 22260 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Special Tec B FE 0W-301 Liter | View on Amazon |
| LIQUI MOLY Fits: 4.4L V8 Turbocharged | 22261 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Special Tec B FE 0W-305 Liter | View on Amazon |
| LIQUI MOLY Fits: 4.4L V8 Turbocharged | 22269 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Special Tec B FE 0W-3020 Liter | View on Amazon |
| PENTOSIN Fits: 3.0L L6 Turbocharged | 8044317 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Pento Speed FESAE 0W-20 | View on Amazon |
| PENTOSIN Fits: 3.0L L6 Turbocharged | 8044319 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Pento Speed FESAE 0W-20 | View on Amazon |
| VALVOLINE Fits: 3.0L L6 Turbocharged | 888048 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | European Vehicle Full Synthetic SAE 0W-201 Quart | View on Amazon |
| VALVOLINE Fits: 4.4L V8 Turbocharged | 893931 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | European Vehicle Full Synthetic SAE 0W-301 Quart | View on Amazon |
This table covers the engine oils listed by grade and specification for this engine. Typical signs include a low-oil lamp, knocking after a long interval, or oil that has gone thin and black well before the next service. Match the viscosity and spec in the notes (and on the filler cap). The tables group grades — they are not interchangeable.
12 Oil parts for the 2021 BMW X7 come from 4 brands — LIQUI MOLY, VALVOLINE, PENTOSIN and 1 other brand. The "Popular" part is LIQUI MOLY 22044.
Oil Cooler
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| NISSENS Fits: 3.0L L6 Turbocharged | 91359 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | without Housing | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | ECK0273 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ÜRO PARTS Fits: 3.0L L6 Turbocharged | 11428583901 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Located on oil filter housing. | View on Amazon |
| VEMO Fits: 3.0L L6 Turbocharged | V20600077 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the heat exchangers that cool engine oil. Typical signs include oil at the cooler fittings, or coolant that looks like a milkshake. Pressure-test both circuits after a cooler swap — a leak here mixes oil and coolant.
4 Oil Cooler parts for the 2021 BMW X7 come from 4 brands — NISSENS, REIN, ÜRO PARTS and 1 other brand.
Part numbers include NISSENS 91359, REIN ECK0273 and ÜRO PARTS 11428583901, among others listed above.
Oil Cooler Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 77010300 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | UpperEngine # B58B30C | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 77010400 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | LowerEngine # B58B30C | View on Amazon |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | B33793 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine Oil Cooler GasketMolded Rubber | View on Amazon |
This table covers the gaskets that seal the Oil Cooler. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
3 Oil Cooler Gasket parts are listed for the 2021 BMW X7, from AJUSA and MAHLE / CLEVITE.
Listed part numbers: AJUSA 77010300, AJUSA 77010400 and MAHLE / CLEVITE B33793.
Oil Drain Plug
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AGS Fits: 3.0L L6 Turbocharged | ODP00010 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | M12x1.50 | View on Amazon |
| DORMAN Fits: 3.0L L6 Turbocharged | 090088 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | MetalStandard | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | HWU1041 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| REIN Fits: 4.4L V8 Turbocharged | HWU0115 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the drain plugs in the oil pan.
4 Oil Drain Plug parts for the 2021 BMW X7 come from 3 brands — REIN, AGS and DORMAN.
Listed part numbers: AGS ODP00010, DORMAN 090088 and REIN HWU1041, plus the other parts above.
Oil Drain Plug Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 21010400 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30Cwith Original Equipment (OE) # 7119963132 | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 21016800 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 417005800 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the crush washers and gaskets under the oil drain plug. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
3 Oil Drain Plug Gasket parts are listed for the 2021 BMW X7, from AJUSA and VICTOR REINZ.
Listed part numbers: AJUSA 21010400, AJUSA 21016800 and VICTOR REINZ 417005800.
Oil Filler Cap
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| MOTORAD Fits: all 2021 X7 engines | MO214 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VAICO Fits: all 2021 X7 engines | V204688 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the caps on the oil filler neck.
2 Oil Filler Cap parts for the 2021 BMW X7 come from 2 brands — MOTORAD and VAICO. Every part fits both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged.
Listed part numbers: MOTORAD MO214 and VAICO V204688.
Oil Filter
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| PRO-TEC Popular Fits: 4.4L V8 Turbocharged | PXL57189 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| CHAMP / LUBER-FINER Fits: 4.4L V8 Turbocharged | P987 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| FAMOUS BRAND Fits: 4.4L V8 Turbocharged | 84189 | 🇺🇸 US 🇨🇦 CA | View on Amazon | |
| FVP Fits: 3.0L L6 Turbocharged | G0342 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| PRO-TEC Fits: 3.0L L6 Turbocharged | PXL10342 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| PUROLATOR Fits: 4.4L V8 Turbocharged | L25904 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ULTRA-POWER Fits: 4.4L V8 Turbocharged | 57189 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Fits or OE # 11-42 7 583 220~ | View on Amazon |
| VARIOUS MFR Fits: 4.4L V8 Turbocharged | PO5904EX | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Extended Life | View on Amazon |
| VARIOUS MFR Fits: 4.4L V8 Turbocharged | PG5904 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
High Performance / Heavy Duty
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| MOBIL Fits: 3.0L L6 Turbocharged | M1C457A | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Extended Performance | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| HENGST Popular Fits: 3.0L L6 Turbocharged | E859HD352 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Gasket SetCartridge | View on Amazon |
| MAHLE / CLEVITE Popular Fits: 4.4L V8 Turbocharged | OX3537D | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Cartridge | View on Amazon |
| MANN Popular Fits: 3.0L L6 Turbocharged | HU6022Z | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| WIX Popular Fits: 4.4L V8 Turbocharged | 57189 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| BECK/ARNLEY Fits: 4.4L V8 Turbocharged | 0410872 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| FEL-PRO Fits: 4.4L V8 Turbocharged | OFCS2006 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Cap and Filter | View on Amazon |
| HASTINGS / BALDWIN Fits: 3.0L L6 Turbocharged | P40076 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| HASTINGS / BALDWIN Fits: 4.4L V8 Turbocharged | LF665 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| HENGST Fits: 4.4L V8 Turbocharged | E359HD306 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Gasket SetCartridge | View on Amazon |
| HENGST Fits: 4.4L V8 Turbocharged | E359HD801 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Gasket SetCartridge | View on Amazon |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | OX1146D | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Cartridge | View on Amazon |
| MANN Fits: 4.4L V8 Turbocharged | HU8007Z | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VARIOUS MFR Fits: 3.0L L6 Turbocharged | PG99256EX | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Extended Life | View on Amazon |
| WIX Fits: 3.0L L6 Turbocharged | WL10342 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the oil filters that screw onto this engine's filter mount. Typical signs include low oil pressure after a service, or a filter that will not spin off because the old gasket stayed on the block. Lube the new gasket and tighten to the spec on the box; a double-gasket install dumps the sump on the first drive.
24 Oil Filter parts for the 2021 BMW X7 come from 15 brands — VARIOUS MFR, HENGST, PRO-TEC and 12 other brands. The "Popular" part is PRO-TEC PXL57189.
The Economy section lists 9 options from PRO-TEC, VARIOUS MFR, CHAMP / LUBER-FINER and 4 other brands — the catalog's value-priced group. PRO-TEC PXL57189 is listed in this group.
The High Performance / Heavy Duty section lists 1 option from MOBIL — grouped under the catalog's "High Performance / Heavy Duty" designation — the notes column spells out what sets them apart. MOBIL M1C457A is listed in this group.
In the Standard Replacement grade, HENGST, MAHLE / CLEVITE, MANN and 5 other brands supply 14 parts: built to original-equipment specification. A representative part number is HENGST E859HD352.
Oil Filter Adapter Gasket / O-Ring
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | B33794 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Filter Adapter GasketMolded Rubber | View on Amazon |
This table covers the Oil Filter Adapter Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.
One part is listed for the 2021 BMW X7 — MAHLE / CLEVITE B33794.
Oil Filter Cover
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ULTRA-POWER Popular Fits: 4.4L V8 Turbocharged | 921111 | 🇺🇸 US 🇨🇦 CA | Oil Filter Cover or CapCover | View on Amazon |
| DORMAN Fits: 4.4L V8 Turbocharged | 921111 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | without Drain Plug | View on Amazon |
| MOTORAD Fits: 3.0L L6 Turbocharged | MO388 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| MOTORAD Fits: 4.4L V8 Turbocharged | MO308 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| REIN Fits: 3.0L L6 Turbocharged | CPL0070 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| REIN Fits: 4.4L V8 Turbocharged | CPL0071 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | with Oil Filter OE# 11427583220 | View on Amazon |
| SKP Fits: 4.4L V8 Turbocharged | SK121443 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | without Drain Plug | View on Amazon |
This table covers the Oil Filter covers.
7 Oil Filter Cover parts are listed for the 2021 BMW X7, from MOTORAD, REIN, ULTRA-POWER and 2 other brands. ULTRA-POWER 921111 carries the "Popular" badge.
Listed part numbers: ULTRA-POWER 921111 and MOTORAD MO388, plus the other parts above.
Oil Filter Housing
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| DORMAN Fits: 3.0L L6 Turbocharged | 926453 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | OE FIX | View on Amazon |
| HENGST Fits: 3.0L L6 Turbocharged | H811H | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | with E859H D352 Filter, Oil Cooler and Bolts/Screws | View on Amazon |
| VEMO Fits: 3.0L L6 Turbocharged | V20601662 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes: Oil cooler, Oil filter housing, seal rings | View on Amazon |
This table covers the Oil Filter housings.
3 Oil Filter Housing parts are listed for the 2021 BMW X7, from DORMAN, HENGST and VEMO.
This group includes DORMAN 926453, HENGST H811H and VEMO V20601662.
Oil Level Sensor
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| HELLA Fits: 4.4L V8 Turbocharged | 010497721 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | 3-Pin ConnectorIncludes Seal | View on Amazon |
| STANDARD MOTOR PRODUCTS Fits: 4.4L V8 Turbocharged | FLS325 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ÜRO PARTS Fits: 4.4L V8 Turbocharged | 12618638754 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | 12VTerminal Type: Blade | View on Amazon |
This table covers the Oil Level sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors.
3 Oil Level Sensor parts for the 2021 BMW X7 come from 3 brands — HELLA, STANDARD MOTOR PRODUCTS and ÜRO PARTS.
Listed part numbers: HELLA 010497721, STANDARD MOTOR PRODUCTS FLS325 and ÜRO PARTS 12618638754.
Oil Level Sensor Gasket / O-Ring
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 4.4L V8 Turbocharged | 16078650 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the Oil Level Sensor Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.
This group shows a single part: AJUSA 16078650.
Oil Pan
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Fits: 3.0L L6 Turbocharged | ESK0249 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Kit | View on Amazon |
This table covers the oil pans that hold the engine's oil sump.
One part is listed for the 2021 BMW X7 — REIN ESK0249.
Oil Pan Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 4.4L V8 Turbocharged | 59018100 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 703141410 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RTV Silicone | View on Amazon |
This table covers the gaskets between the oil pan and the block. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
2 Oil Pan Gasket parts for the 2021 BMW X7 come from 2 brands — AJUSA and VICTOR REINZ.
This group includes AJUSA 59018100 and VICTOR REINZ 703141410.
Oil Pump Chain
Kit
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| VAICO Popular Fits: 3.0L L6 Turbocharged | V203921 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Expert Kits +Oil Pump Drive Set | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| S.A. GEAR Fits: 3.0L L6 Turbocharged | C1213 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| S.A. GEAR Fits: 3.0L L6 Turbocharged | 76437P | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes Chain, Oil Pump SprocketOil Pump Drive Set | View on Amazon |
| S.A. GEAR Fits: 3.0L L6 Turbocharged | C1165 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | C530 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine Oil Pump Chain | View on Amazon |
| VAICO Fits: 4.4L V8 Turbocharged | V203921 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Expert Kits +Oil Pump Drive Set | View on Amazon |
This table covers the chains that drive the oil pump.
6 Oil Pump Chain parts are listed for the 2021 BMW X7, from S.A. GEAR, VAICO and CLOYES. VAICO V203921 carries the "Popular" badge.
In the Kit grade, VAICO supplies 1 part: grouped under the catalog's "Kit" designation — the notes column spells out what sets them apart. A representative part number is VAICO V203921.
The Standard Replacement section: 3 options from S.A. GEAR. S.A. GEAR C1213 is listed in this group.
2 ungrouped parts are not assigned to a grade, with the same engine-level match.
Listed part numbers: VAICO V203921, S.A. GEAR C1213 and S.A. GEAR 76437P, plus the other parts above.
Oil Pump Sprocket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | S1172 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the Oil Pump sprockets.
One part is listed for the 2021 BMW X7 — CLOYES S1172.
Timing Chain
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | C528 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the timing chains that keep the cams in time with the crank.
One part is listed for the 2021 BMW X7 — CLOYES C528.
Timing Chain & Component Kit
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| S.A. GEAR Popular Fits: 3.0L L6 Turbocharged | 76399 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | 90528SAX | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Does Not Include SprocketsIncludes Timing Chain Tensioner, Chain Guide (2), Chain Tensioner Guide, Timing Chain, Oil Pump Chain | View on Amazon |
| CLOYES Fits: 3.0L L6 Turbocharged | 90528SA | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes: Timing Chain Tensioner, Timing Chain Guide (2), Timing Chain Tensioner Guide, Timing Chain, Oil Pump Chain, Oil Pump Sprocket | View on Amazon |
| VAICO Fits: 3.0L L6 Turbocharged | V2010026BEK | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes: Timing chains, Tensioner, Guides | View on Amazon |
| VAICO Fits: 3.0L L6 Turbocharged | V2010026 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Includes: Timing Chain, Tensioner, Guides, camshaft adjusters, bolts | View on Amazon |
This table covers kits that group a timing chain with the related tensioners and guides.
5 Timing Chain & Component Kit parts for the 2021 BMW X7 come from 3 brands — CLOYES, VAICO and S.A. GEAR. The "Popular" part is S.A. GEAR 76399.
The Economy section: 1 option from S.A. GEAR. S.A. GEAR 76399 is listed in this group.
Standard Replacement: 4 parts, from CLOYES and VAICO. A representative part number is CLOYES 90528SAX.
Listed part numbers: S.A. GEAR 76399, CLOYES 90528SAX and CLOYES 90528SA, plus the other parts above.
Timing Chain Guide / Damper
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | 96180 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine Timing Chain Guide | View on Amazon |
| CLOYES Fits: 3.0L L6 Turbocharged | 96181 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine Timing Chain Guide | View on Amazon |
| CLOYES Fits: 3.0L L6 Turbocharged | 96182 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine Timing Chain Tensioner Guide | View on Amazon |
This table covers the guides and dampers that keep the timing chain on its path.
CLOYES supplies the 3 Timing Chain Guide / Damper parts for the 2021 BMW X7.
This group includes CLOYES 96180, CLOYES 96181 and CLOYES 96182.
Timing Chain Tensioner
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| CLOYES Fits: 3.0L L6 Turbocharged | 96179 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine Timing Chain Tensioner | View on Amazon |
This table covers the tensioners that keep the timing chain taut. Typical signs include belt flutter, a chirp that returns after a new belt, or an arm that no longer damps. Replace the tensioner with the belt at higher mileage.
This group shows a single part: CLOYES 96179.
Timing Cover Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 4.4L V8 Turbocharged | 77031300 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the gaskets that seal the Timing Cover. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
This group shows a single part: AJUSA 77031300.
Timing Cover Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| FEL-PRO Fits: 4.4L V8 Turbocharged | TCS46311 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Front | View on Amazon |
| MAHLE / CLEVITE Fits: 4.4L V8 Turbocharged | 67930 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | PTFE (Polytetrafluoroethylene) | View on Amazon |
This table covers the seals at the Timing Cover. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
2 Timing Cover Seal parts for the 2021 BMW X7 come from 2 brands — FEL-PRO and MAHLE / CLEVITE.
Listed part numbers: FEL-PRO TCS46311 and MAHLE / CLEVITE 67930.
Turbocharger
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| BORG-WARNER Fits: 3.0L L6 Turbocharged | 18559880115 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | with OE No. 11657934386 | View on Amazon |
| GPD Fits: 3.0L L6 Turbocharged | 2512001 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | with Electronic Actuator | View on Amazon |
This table covers the turbochargers that compress intake air.
2 Turbocharger parts for the 2021 BMW X7 come from 2 brands — BORG-WARNER and GPD.
Listed part numbers: BORG-WARNER 18559880115 and GPD 2512001.
Turbocharger Boost Sensor
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| BECK/ARNLEY Fits: 4.4L V8 Turbocharged | 1581726 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| HELLA Fits: 4.4L V8 Turbocharged | 358152381 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | 4-Pin ConnectorBolted | View on Amazon |
This table covers the Turbocharger Boost sensors. Typical signs include a warning lamp, a stored code, or a reading that drops out when the harness is wiggled. Inspect the connector and ground before replacing the sensor — wiring faults are often condemned as bad sensors.
2 Turbocharger Boost Sensor parts are listed for the 2021 BMW X7, from BECK/ARNLEY and HELLA.
This group includes BECK/ARNLEY 1581726 and HELLA 358152381.
Turbocharger Coolant Line
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Fits: 3.0L L6 Turbocharged | CHT0972 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Return | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | CHT0971 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Supply | View on Amazon |
| REIN Fits: 4.4L V8 Turbocharged | CHT0698 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Return (Turbocharger To Pipe)For Cylinder 5-8 | View on Amazon |
| REIN Fits: 4.4L V8 Turbocharged | CHT0697 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Supply (Turbocharger To Pipe)For Cylinder 1-4 | View on Amazon |
| REIN Fits: 4.4L V8 Turbocharged | CHT0695 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Supply (Turbocharger To Pipe)For Cylinder 5-8 | View on Amazon |
This table covers the Turbocharger Coolant lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early.
5 Turbocharger Coolant Line parts for the 2021 BMW X7 come from REIN.
Listed part numbers: REIN CHT0972, REIN CHT0971 and REIN CHT0698, plus the other parts above.
Turbocharger Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | JTC12513 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Mounting Gasket Set | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 01158200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Exhaust | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | JTC12221 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Mounting Gasket Set | View on Amazon |
| ELRING Fits: all 2021 X7 engines | 074140 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Suction PipeInlet Gasket | View on Amazon |
| GPD Fits: 3.0L L6 Turbocharged | 2535112 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Only Fits Compatible Aftermarket Turbochargers | View on Amazon |
This table covers the gaskets that seal the Turbocharger. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
5 Turbocharger Gasket parts are listed for the 2021 BMW X7, from AJUSA, ELRING and GPD. 1 part fits every engine; the other 4 are engine-specific.
Part numbers include AJUSA JTC12513, AJUSA 01158200 and AJUSA JTC12221, among others listed above.
Turbocharger Mounting Hardware
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| REIN Fits: 3.0L L6 Turbocharged | TRK0024 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the fasteners that mount the turbocharger.
One part is listed for the 2021 BMW X7 — REIN TRK0024.
Turbocharger Oil Line
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | OP11237 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30CSupply Tube | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | OP11235 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | for Cylinders 1 To 4 OnlySupply Tube | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | OP11307 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | for Cylinders 5 To 8 OnlySupply Tube | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | TFP0393 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Supply Line | View on Amazon |
| REIN Fits: 3.0L L6 Turbocharged | TRP0391 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Return Line | View on Amazon |
| REIN Fits: 4.4L V8 Turbocharged | TFP0345 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | For Cyl. 1-4Supply Line | View on Amazon |
| VAICO Fits: 4.4L V8 Turbocharged | V204576 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Feed Line | View on Amazon |
This table covers the Turbocharger Oil lines. Typical signs include a wet fitting, a rusted pipe, or a pressure loss in this circuit. Flare or thread the new line the way the notes specify; a kinked replacement will fail early.
7 Turbocharger Oil Line parts for the 2021 BMW X7 come from 3 brands — AJUSA, REIN and VAICO.
This group includes AJUSA OP11237, AJUSA OP11235 and AJUSA OP11307 and the remaining parts above.
Turbocharger Oil Line Gasket / O-Ring
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 16007800 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Turbocharger Coolant Line O-Ring | View on Amazon |
This table covers the Turbocharger Oil Line Gasket O-rings. Typical signs include a seep at a fitting or a housing that weeps after a service. Lube the new O-ring with the fluid it will see, and do not roll it into the groove.
This group shows a single part: AJUSA 16007800.
Valve Cover
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| SKP Fits: all 2021 X7 engines | SK743462 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| VAICO Fits: 3.0L L6 Turbocharged | V205366 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Plastic | View on Amazon |
This table covers the Valve covers.
2 Valve Cover parts are listed for the 2021 BMW X7, from SKP and VAICO. 1 part fits every engine; the other 1 is engine-specific.
Part numbers include SKP SK743462 and VAICO V205366.
Valve Cover Gasket
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: 3.0L L6 Turbocharged | 56080600 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 56081400 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | LeftFor Cylinders 5 to 8 Only | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 56081500 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | RightFor Cylinders 1 to 4 Only | View on Amazon |
| VICTOR REINZ Fits: 3.0L L6 Turbocharged | 151120501 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Set | View on Amazon |
This table covers the gaskets that seal the valve cover to the cylinder head. Typical signs include seepage at the joint, a burnt-oil smell, or a leak that appears only after a long drive. Clean both flanges and torque in the sequence the notes or the manual call for.
4 Valve Cover Gasket parts for the 2021 BMW X7 come from 2 brands — AJUSA and VICTOR REINZ.
Part numbers include AJUSA 56080600, AJUSA 56081400 and AJUSA 56081500, among others listed above.
Valve Lifter
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: all 2021 X7 engines | 85022300 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
This table covers the lifters / tappets that transfer cam motion to the valves.
This group shows a single part: AJUSA 85022300.
Valve Stem Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| VICTOR REINZ Popular Fits: 3.0L L6 Turbocharged | 123686601 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | SetContains 12 Pieces | View on Amazon |
| VICTOR REINZ Popular Fits: 3.0L L6 Turbocharged | 123725601 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | SetContains 12 Pieces | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 57051500 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Engine # B58B30C | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 12027900 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | IntakeEngine # B58B30C | View on Amazon |
| AJUSA Fits: 3.0L L6 Turbocharged | 12028200 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | ExhaustEngine # B58B30C | View on Amazon |
| AJUSA Fits: 4.4L V8 Turbocharged | 12033700 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| AJUSA Fits: 4.4L V8 Turbocharged | 57069600 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| MAHLE / CLEVITE Fits: 3.0L L6 Turbocharged | SS46008 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | SetMetal with Molded Rubber | View on Amazon |
| VICTOR REINZ Fits: 4.4L V8 Turbocharged | 123728101 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Set | View on Amazon |
This table covers the seals on each valve stem that control oil into the guides. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
9 Valve Stem Seal parts for the 2021 BMW X7 come from 3 brands — AJUSA, VICTOR REINZ and MAHLE / CLEVITE. The "Popular" part is VICTOR REINZ 123686601.
Part numbers include VICTOR REINZ 123686601, VICTOR REINZ 123725601 and AJUSA 57051500, among others listed above.
Variable Valve Timing (VVT) Eccentric Shaft Actuator
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| ÜRO PARTS Fits: 4.4L V8 Turbocharged | 11378652738 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | For Valvetronic System | View on Amazon |
This table covers the Variable Valve Timing (VVT) Eccentric Shaft actuators. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same.
This group shows a single part: ÜRO PARTS 11378652738.
Variable Valve Timing (VVT) Solenoid / Actuator
Economy
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| GATES Popular Fits: 4.4L V8 Turbocharged | VVS229 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| ÜRO PARTS Popular Fits: 4.4L V8 Turbocharged | 11367614288 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | For Vanos System | View on Amazon |
| HOLSTEIN Fits: 4.4L V8 Turbocharged | 2VTS0370 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Adjuster Magnet | View on Amazon |
| VAICO Fits: 4.4L V8 Turbocharged | V204822 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| VEMO Fits: 4.4L V8 Turbocharged | V20540005 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| WELLS Fits: 4.4L V8 Turbocharged | 2T1286 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Adjuster Magnet | View on Amazon |
| WELLS Fits: 4.4L V8 Turbocharged | 2T1247 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| WELLS Fits: 4.4L V8 Turbocharged | 2T1249 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
Standard Replacement
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| VAICO Fits: 4.4L V8 Turbocharged | V203994 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| GATES Popular Fits: 3.0L L6 Turbocharged | VVS229 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon | |
| HOLSTEIN Fits: 3.0L L6 Turbocharged | 2VTS0370 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Adjuster Magnet | View on Amazon |
| ÜRO PARTS Fits: 3.0L L6 Turbocharged | 11368696446 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| VAICO Fits: 3.0L L6 Turbocharged | V204625 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| VEMO Fits: 3.0L L6 Turbocharged | V20540005 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Control | View on Amazon |
| VNE Fits: 3.0L L6 Turbocharged | 4022002 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Actuator | View on Amazon |
| VNE Fits: 3.0L L6 Turbocharged | 4022005 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | Oil Pump Control Valve | View on Amazon |
This table covers the oil-control solenoids that command the cam phasers. Typical signs include a door or range that will not move, or a click with no motion. Confirm the command signal before replacing the actuator — a failed module looks the same.
16 Variable Valve Timing (VVT) Solenoid / Actuator parts for the 2021 BMW X7 come from 7 brands — VAICO, WELLS, GATES and 4 other brands. The "Popular" part is GATES VVS229.
The Economy section: 8 options from WELLS, GATES, ÜRO PARTS and 3 other brands. GATES VVS229 is listed in this group.
Standard Replacement: 1 part, from VAICO. A representative part number is VAICO V203994.
7 further parts sit outside the graded sections, with the same engine-level match.
Variable Valve Timing (VVT) Solenoid Gasket / Seal
| Brand | Part Number | Markets | Notes | Buy |
|---|---|---|---|---|
| AJUSA Fits: all 2021 X7 engines | 01907000 | 🇺🇸 US 🇨🇦 CA 🇲🇽 MX | View on Amazon |
This table covers the seals at the Variable Valve Timing (VVT) Solenoid Gasket. Typical signs include a wet housing, a drip after sitting, or fluid flung off a rotating shaft. Fix the surface the seal rides on. A new seal on a grooved shaft will leak again.
One part is listed for the 2021 BMW X7 — AJUSA 01907000.
Buying Engine Parts for a 2021 BMW X7
On this vehicle, the engine covers the internals and hard parts that build compression and keep oil where it belongs — gaskets, bearings, camshafts, lifters, seals and timing components.
- Match the engine first. Some engine parts fit every engine; others are engine-specific. Each row shows which engine(s) it fits.
- Read the notes on each row for position, trim and spec qualifiers before you order.
- Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
- Cross-reference the manufacturer part number against your old part or a service-manual listing.
Start with the largest groups on this page: Oil Filter and Variable Valve Timing (VVT) Solenoid / Actuator .
Frequently Asked Questions
How many engine parts fit the 2021 BMW X7?
Our catalog currently lists 196 engine parts for the 2021 BMW X7 across 48 subcategories and 46 brands, covering both the 3.0L L6 Turbocharged and the 4.4L V8 Turbocharged. Each part is matched to the engine(s) it fits.
Do engine parts differ between 2021 BMW X7 engines?
Some do. 9 parts fit every engine; the other 187 are engine-specific. Each row (and the filter at the top) shows which. If you're unsure which engine you have, check the emissions label under the hood or the 8th character of your VIN.
What are the signs of engine problems on a 2021 BMW X7?
Common symptoms include oil spots under the vehicle, blue or white exhaust smoke, ticking from the valvetrain, or coolant mysteriously disappearing. If you notice any of these, identify the affected subcategory above and cross-reference the part numbers listed.
What oil viscosity is listed for the 2021 BMW X7?
Oil rows on this page include SAE 0W-20, SAE 0W-30 and SAE 5W-30. Confirm the engine and the weight on the filler cap before you buy — high-mileage and standard fills can differ.
What should I replace at the same time?
Where labor overlaps, replace the seals and gaskets for anything you open up; a timing job should always include the tensioner and guides, not just the belt or chain.
What do the market flags (US, CA, MX) on each part mean?
They show the market for which the manufacturer published application data for that part — where the vehicle was first sold, not where the part was made. If your 2021 BMW X7 was originally sold in the US, the safest choice is a part marked for the US market.
How do I make sure a part fits my 2021 BMW X7?
First match the engine — each row shows which engine(s) the part fits. Then engine hard parts are unforgiving of guesswork — confirm the casting or engine code before ordering, because one model year can hide two different blocks. The notes column carries position and trim qualifiers where they apply.
Other Parts for the 2021 BMW X7
Engine Parts for Other BMW X7 Years
Switch vehicle or jump to a subcategory
Manufacturer names, model designations and part numbers are used for identification and fitment reference only. AutoFactsDB is an independent catalog and is not affiliated with, endorsed by, or sponsored by any vehicle manufacturer displayed on this page.